I think G4ZFQ is the only site transmitting on both 60M bands during the same WSPR cycle. Perhaps he too doesn't know that 1/2 of such spots are being rejected by wsprnet.org -- Rob

If you send me a list of rejected spots I will try to enhance the filtering I already do on spots before uploading them thanks -- Rob Robinett AI6VN rob@... mobile: +1 650 218 8896

I have started tracking which spots get rejected on wsprnet uploads. The wsprdaemon.sh -le command in v3.02 is useful for doing this. I have found 2 categories so far bad decodes

I almost always execute 'wd -a' to start WD and 'wd -z' to stop it. However if you want to have WD start automatically after power-up or reboot, then execute 'wd -A'. It configures Linux to run WD at

Hi Gerhard, I think you may need to stop your WD 2.10 before starting WD 3.0.2 If you are already doing that, then I would need ssh access to your odroid to further debug the problem. PM me if you

I have just checked in a revision of that file which (I hope) fixes a few errors and adds a much more detailed explanation of the settings in your wsprdaemon.conf For those of you already running

Hi Rob, What I did since: Installed WD 2.10 on clean Odroid XU4 without problems and was runing 14 chanals over night. Now changed to v3.0 and the problem with reconnection to the SDR happend

with CHU close by to NY.... we might find similar of use here On 5/21/22 14:17, Rob Robinett wrote:

In response to a user request, have tested and checked in enhancements to 3.0.2.4 which add support for the feature you requested which runs the quickest wsprd on those 'noise level only' bands like

Thanks dear Rob, OK all I'm looking forward to apply RTL-SDR. 73, Hidehiko JA9MAT

I'm sorry but it is a completely untested feature and I was unable to find a driver which could tune the RTL with sufficient accuracy for WSPR decoding. -- Rob Robinett AI6VN rob@... mobile: +1 650

Hello, I'd like to test RTL-SDR on WD 3.0 beta version. Is this avairable now? Hidehiko JA9MAT

run 'wsprdaemon.sh -l e' and you will see all log lines with "ERROR ..." they might give you a clue as to why your system isn't working. -- Rob Robinett AI6VN rob@... mobile: +1 650 218 8896

Hi, Have installed V3.0 first on the odroid XU4 (Ubuntu). Istallation seems to be OK, but did not work. The connection to the SDR is allways broken right after 2 minutes. Therefore no decoding and

Look in wd_template.conf for explanations of the format. During startup WD now checks that there is enough space in the tmpfs /tmp/wsprdaemon file system for the wav files recordings ### Following the

Hi Rob 3.0.2 has been running drama-free on my Pi4 here. I will look to see what is needed to enable FST4W. Is there a sample config or a README to help? John K5MO

I know that in the recent past Jim WA2ZKD has installed WD on his odroid systems. WD 3.0 includes the option for you to configure it to give me remote access if you need installation help. -- Rob

Hello Rob, great news! I am running the monitor at OE3XOE, at the moment using DigiSkimmer for WSPR and FT8. I will try V3, but I would like to use a Odroid XU4 instead a RPI4. Do you have

Hi Bryan, In the latest 3.0.2 I have disabled some excessive internal validation code which might have contributed to the additional CPU load. But in your case the much bigger problem is a memory leak

The new Wsprdaemon version 3.0 software running on 20 sites from Maui to Europe is configured to simultaneously decode and report to wsprnet.org WSPR-2 and all of the FST4W-xxx modes on 630M and 160M.