what type antenna do you use on 40M? -Jim WA2ZKD

For info, just checked WSPR: I could receive at OE3XOE several DX stations using powers of 5 and 10 mW: 73 de Gerhard OE3GBB Am 05.10.2021 05:08, schrieb Bruce KX4AZ:

Thanks Gwyn, Fascinating plots. I just lowered my RF output power to -13 dBm (50 microwatts)....i.e. effective 1527 UTC on 5 October 2021. I've attached a screen shot for the past 24 hours at -10 dBm

Hi Bruce, that is a great idea! Will have to try this also. I once have done a similar test to see the minimal power to reach a DX station. That would be an indication on how good the antenna is at

Hello Bruce Nice to read of your experiments, and I look forward to seeing the results of your 50 microwatts and below transmissions. The attachment is a screenshot of three plots from the WsprDaemon

One of my favorite pastimes over the past few years has been playing a WSPR "game" I have taken to calling "radio limbo", i.e how low in RF output power can I go and still be spotted. Since about

Hi, thanks for letting me know. Its fixed by now. Regards

This issue is more for Arne, but I do not have his e-mail adres. Perhaps someone can forward to him ? -------------- so: For Arne ---------------- Problem: Page: WSPR Daemon/ Station Noise stats This

To all: the reason of the problem has been identified and solved. No need for vers 1.461 anymore... I updated in the meantime to the most recent version Ulli

I ssh'ed into my dead Kiws at KPH and KFS and ran: 'cdp;up' from the command line to upgrade them to 464 -- Rob Robinett AI6VN rob@... mobile: +1 650 218 8896

Hi Tom. I only have original 8 channel kiwis, no AI version... I just made a flash card with Vers 1.464, but it doesn't install reliably. Only 2 kiwis work with that card... So better to get back with

Ulli, Do you need a backup for kiwi with BBAI, or a backup from a standard beaglebone green kiwi? Tom WA2TP

Ulli, My radios are off and still at 1.461 but I am in Iceland until the 5th of October. If you have not resolved this by then I will make a backup before I upgrade them. I would think that John on

My kiwis are all offline, as latest kiwi version 1.464 upgrade don't work Has someone a backup of Vers. 1.461 and can offer this for download ? I have older backups, but not 1.461 Version 1.461 was

Hi Stefan, Thanks for that information. I am deep into implementing WD 3.0 and the first new feature is support for FST4W up to all lengths at the same time. I was aware of the mode number issue

Hi Rob & group, WSJT-X currently reports FST4W-120 as mode "3", you might want to use that, too. But it isn't supported by wsprnet yet. (Wsprnet rewrites all other values than 2, 5, 15 and 30 to

Thanks Bill, I'll set up KPH to listen on 160M FST4W overnight. If KPHsuccessful you will see those spots in the wspr.live report pages. Rob -- Rob Robinett AI6VN rob@... mobile: +1 650 218 8896

Rob - I just saw this - I was checking the wrong email earlier this AM. Please disregard my earlier email of today. I have added the standard WSPR frequency of 1.836600 MHz to my WSJT-x instance for

Reading the FST4 Quick Start Guide at: https://physics.princeton.edu/pulsar/k1jt/FST4_Quick_Start.pdf I see it suggested that FST4 transmissions occupy the same 1400-1600 Hz bands as WSPR signals. So

Hi Bill, I posted questions about the FST4W bands and frequencies to the WSJT-x forum and heard back in this thread: https://wsjtx.groups.io/g/main/topic/85595606#28773 This is my first exploration of