Hey Rob-- Thanks for the tips on decreasing the "-o" flag if I run out of cycles. My current KF6ZEO spotting station is actually running on a Ubuntu 20.04 VM with 2 threads of a i3-5010U, so it's got

The memory leak is in the Bash version 5.1.4 included in bullseye. Gwyn has compiled Bash 5.1.16 on his bullseye Pi 3b and that fixes the problem. I have no insight into if/when they will update the

Rob mentions: in your case the much bigger problem is a memory leak in the Bash 5.1.4 included in bullseye. Gwyn G3ZIL identified that problem which leads the Pi to run out of memory in 1-5 days. I

Thanks Rob, looking forward to hearing how well it works. I ordered one as well from Aliexpress - the one with five SMA filter inputs. The main difference versus the single input with the DIP

First of all these are clones of the way outdated version RSP1, not the later RSP1a. And also the "designer" tells it is a simplified design. So I would not be to hopeful on performance. If it will

Perhaps I could tune the RP1/2 to a carrier generated by a GPSDO on the bench next to the RP and then use the measured tuning error to adjust the WSPR tuning frequency. That isn't nearly as good as

Unfortunately upon surveying  > 30 OTA HDTV broadcasts here on Colorado 's Front Range with my GPSDO referenced 0-2 GHz Frequency Extender, hearing HDTV ATSC pilot carriers from well South of Denver

Hi Bruce, Thanks for that post. I have ordered one of those clones from ebay if only to compare it against my RP2. I had my RP2 working with WD 3.0 last year, and I will check to see if that code is

Hi Bryan, I see from http://wspr.rocks/livequeries/ that you are still running 3.0.2.3. You would benefit from updating your WD by running: git pull wd -z wd -a I have just installed Wd 3.0.2 at many

to date, nearly every misformed spot has been missing a grid, so that would be an easy filter I think

I informed him.... and he is going to revise his scheme at some point

I happened to notice on Aliexpress (search for 'RSP1') there are a ton of RSP1 clones based on the msi2500 chip, that have either a single input with DIP switches for input filtering, or are equipped

I think G4ZFQ is the only site transmitting on both 60M bands during the same WSPR cycle. Perhaps he too doesn't know that 1/2 of such spots are being rejected by wsprnet.org -- Rob

If you send me a list of rejected spots I will try to enhance the filtering I already do on spots before uploading them thanks -- Rob Robinett AI6VN rob@... mobile: +1 650 218 8896

I have started tracking which spots get rejected on wsprnet uploads. The wsprdaemon.sh -le command in v3.02 is useful for doing this. I have found 2 categories so far bad decodes

I almost always execute 'wd -a' to start WD and 'wd -z' to stop it. However if you want to have WD start automatically after power-up or reboot, then execute 'wd -A'. It configures Linux to run WD at

Hi Gerhard, I think you may need to stop your WD 2.10 before starting WD 3.0.2 If you are already doing that, then I would need ssh access to your odroid to further debug the problem. PM me if you

I have just checked in a revision of that file which (I hope) fixes a few errors and adds a much more detailed explanation of the settings in your wsprdaemon.conf For those of you already running

Hi Rob, What I did since: Installed WD 2.10 on clean Odroid XU4 without problems and was runing 14 chanals over night. Now changed to v3.0 and the problem with reconnection to the SDR happend

with CHU close by to NY.... we might find similar of use here