Date   

Re: FLDigi in LSB mode

 

When I downloaded the then latest alpha of flrig, AVG wanted to send both the installer and the installed flrig away for further analysis. I overrode both without a problem. When my licenses run out I am going to try Windows Defender instead. Mind you on another machine Defender moaned about them occasionally.

 

73 Phil GM3ZZA.

 

Sent from Mail for Windows 10

 

From: Rodney via groups.io
Sent: 11 January 2021 09:56
To: winfldigi@groups.io
Subject: Re: [winfldigi] FLDigi in LSB mode

 

Dave,
I was able to download the two programs without the "message".

Thanks - 73,
Rodney - N3QLB

 


Re: FLDigi in LSB mode

Rodney
 

Dave,
I was able to download the two programs without the "message".

Thanks - 73,
Rodney - N3QLB


Re: Carrier before data sent #fldigi

 

Doug,

For my Icom IC-7300 I use either Hamlib or Flrig. The FT-DX5000 is listed in the drop downs so it should work. Make sure that you have the correct driver from Yaesu and the other settings like the baud rate matches the radio settings. Maybe someone with that radio can share their settings.

73, Ron NY3J

On 1/10/21 8:29 PM, DOUGLAS FRIEDT via groups.io wrote:

Hi Ron,

Thank you very much, that was the fix!

Might I ask another question?

I also have an FT-DX5000 and have been able to get it to work with HRD and SDR UNO, but can’t get it to work with fldigi.  I set it up just like the FT-991, but used the profile for the 5000.  I suspect it is something with the menu settings in the 5000, but I have not found any setups for it on the internet.

Thanks again, and take care

Doug
N8FRJ


On Jan 10, 2021, at 12:49 PM, Ron NY3J via groups.io <rwenig@...> wrote:

 Doug,

Check the setting in Configure, IDs, RsID, Pre-Signal Tone. This will send a tone before the data is sent. Set it to zero for no tone.

<heanbpfkjfgkdifc.png>


73, Ron NY3J

On 1/10/21 10:37 AM, DOUGLAS FRIEDT via groups.io wrote:
Good Morning

I started using fldigi about a month ago with an FT-991.  When I transmit in RTTY, CW or PSK, there is a four second carrier before any data is sent.  I am using a PC with an i7 chip 2.2Ghz, 6 cores and 16GB of RAM.  I close all applications except fldigi so as not to overburden the processor.  I have not found any settings to adjust.

Any help would be greatly appreciated.

Thanks
Doug
N8FRJ



Re: Carrier before data sent #fldigi

DOUGLAS FRIEDT
 

Hi Ron,

Thank you very much, that was the fix!

Might I ask another question?

I also have an FT-DX5000 and have been able to get it to work with HRD and SDR UNO, but can’t get it to work with fldigi.  I set it up just like the FT-991, but used the profile for the 5000.  I suspect it is something with the menu settings in the 5000, but I have not found any setups for it on the internet.

Thanks again, and take care

Doug
N8FRJ


On Jan 10, 2021, at 12:49 PM, Ron NY3J via groups.io <rwenig@...> wrote:

 Doug,

Check the setting in Configure, IDs, RsID, Pre-Signal Tone. This will send a tone before the data is sent. Set it to zero for no tone.

<heanbpfkjfgkdifc.png>


73, Ron NY3J

On 1/10/21 10:37 AM, DOUGLAS FRIEDT via groups.io wrote:
Good Morning

I started using fldigi about a month ago with an FT-991.  When I transmit in RTTY, CW or PSK, there is a four second carrier before any data is sent.  I am using a PC with an i7 chip 2.2Ghz, 6 cores and 16GB of RAM.  I close all applications except fldigi so as not to overburden the processor.  I have not found any settings to adjust.

Any help would be greatly appreciated.

Thanks
Doug
N8FRJ


Re: FLDigi in LSB mode

Rodney
 

Dave,
I am trying to download the setup.exe for flrig and fldigi but I am getting "can't be downloaded securely" message.
I have tried this within groups.io and also the email. Same message.
I do have the option to keep, but I want to make sure that it is ok.  I am using Google Chrome.

Thanks,
Rodney - N3QLB


Re: FLDigi in LSB mode

Kenneth G. Gordon
 

On 10 Jan 2021 at 11:00, Dave wrote:

Just my opinion, but virus protection software is like buying arson
insurance from the mafia.

Dave
Agreed. In addition, McAfee and Norton's are notorious for false-positives. I was an IT Pro at
the University of Idaho for over 30 years. At one time, Norton's even "decided" that MS-Word
was a virus.

Ken W7EKB


Re: MinGW Runtime Assertion - Assertion failed

Dave
 

Thank you both for your reports of successful trouble shooting.  The usual cause of the error is a device driver that is not responding iaw specifications.

David

On 1/10/21 4:19 PM, NoName via groups.io wrote:

Good fix here too.  I have a virtual audio device associated with another software package that when disabled allows fldigi to start up error free.  Thanks to Greg for posting what you found!

Chris

----------------------------------------
In God We Trust
All who call on the name of the Lord will be saved - Romans 10:13
A Prudent man sees danger and takes refuge, but the simple keep going and suffer for it - Proverbs 22:3
On 1/10/2021 11:57 AM, Greg Hidley via groups.io wrote:
Solved the problem!  It was a sound card interfering ... in my case it turned out to be "C-Media PCI Audio Device". Disabling it allowed fldigi to startup error free.

Did this by opening device manager, opening sound devices, and go down the list disabling one at a time until you find the culprit. Obviously you should not disable the sound card device that fldigi is set use! In my case, I was fortunately not using the C-Media device. 

greg

Virus-free. www.avast.com


Re: MinGW Runtime Assertion - Assertion failed

NoName
 

Good fix here too.  I have a virtual audio device associated with another software package that when disabled allows fldigi to start up error free.  Thanks to Greg for posting what you found!

Chris

----------------------------------------
In God We Trust
All who call on the name of the Lord will be saved - Romans 10:13
A Prudent man sees danger and takes refuge, but the simple keep going and suffer for it - Proverbs 22:3
On 1/10/2021 11:57 AM, Greg Hidley via groups.io wrote:
Solved the problem!  It was a sound card interfering ... in my case it turned out to be "C-Media PCI Audio Device". Disabling it allowed fldigi to startup error free.

Did this by opening device manager, opening sound devices, and go down the list disabling one at a time until you find the culprit. Obviously you should not disable the sound card device that fldigi is set use! In my case, I was fortunately not using the C-Media device. 

greg

Virus-free. www.avast.com


Re: Need some help

Greg Hidley
 

Your recommendation solved the problem!  It was a sound card interfering ... in my case it turned out to be "C-Media PCI Audio Device". Disabling it allowed fldigi to startup error free.

Did this by opening device manager, opening sound devices, and go down the list disabling one at a time until you find the culprit. Obviously you should not disable the sound card device that fldigi is set use! In my case, I was fortunately not using the C-Media device. 

greg


Re: FLDigi in LSB mode

Philip Salley
 

LOL Dave, couldn't have said it better.  Regards, Phil / K4PO


Re: MinGW Runtime Assertion - Assertion failed

Greg Hidley
 

Solved the problem!  It was a sound card interfering ... in my case it turned out to be "C-Media PCI Audio Device". Disabling it allowed fldigi to startup error free.

Did this by opening device manager, opening sound devices, and go down the list disabling one at a time until you find the culprit. Obviously you should not disable the sound card device that fldigi is set use! In my case, I was fortunately not using the C-Media device. 

greg


log data question

jim crisco WA4YIZ
 

hi all...
have not been on fldigi for a while...just updated to latest...
used to...when i clicked on a call in rt panel..would place call in
field at top...and would add state...county...location-grid...etc..
does not load that data now...
also..i and sending each log to ACL
have i missed something..??

thanks
jim
wa4yiz

fldigi screen shot.jpgfldigi screen shot 2.jpg


Re: http://www.w1hkj.com/flrig-help/ft991a_how_to_page.html

Dave
 

I'll check the help source files.

Dave

On 1/9/21 12:21 PM, Tom - K5EIS via groups.io wrote:

Hi Dave;
The subject "FT991a how to page" apparently contains an invalid picture link as follows:
flirig-fldigi.png
since no picture displays for it. Probably the extra "i" between "fl" and "rig".
Thought you might like to know about it and correct it.







Re: http://www.w1hkj.com/flrig-help/ft991a_how_to_page.html

Dave
 

Not seeing that in the Wiki:


Dave

On 1/9/21 12:21 PM, Tom - K5EIS via groups.io wrote:

Hi Dave;
The subject "FT991a how to page" apparently contains an invalid picture link as follows:
flirig-fldigi.png
since no picture displays for it. Probably the extra "i" between "fl" and "rig".
Thought you might like to know about it and correct it.







Re: Carrier before data sent #fldigi

 

Doug,

Check the setting in Configure, IDs, RsID, Pre-Signal Tone. This will send a tone before the data is sent. Set it to zero for no tone.



73, Ron NY3J

On 1/10/21 10:37 AM, DOUGLAS FRIEDT via groups.io wrote:

Good Morning

I started using fldigi about a month ago with an FT-991.  When I transmit in RTTY, CW or PSK, there is a four second carrier before any data is sent.  I am using a PC with an i7 chip 2.2Ghz, 6 cores and 16GB of RAM.  I close all applications except fldigi so as not to overburden the processor.  I have not found any settings to adjust.

Any help would be greatly appreciated.

Thanks
Doug
N8FRJ


Carrier before data sent #fldigi

DOUGLAS FRIEDT
 

Good Morning

I started using fldigi about a month ago with an FT-991.  When I transmit in RTTY, CW or PSK, there is a four second carrier before any data is sent.  I am using a PC with an i7 chip 2.2Ghz, 6 cores and 16GB of RAM.  I close all applications except fldigi so as not to overburden the processor.  I have not found any settings to adjust.

Any help would be greatly appreciated.

Thanks
Doug
N8FRJ


http://www.w1hkj.com/flrig-help/ft991a_how_to_page.html

Tom - K5EIS
 

Hi Dave;
The subject "FT991a how to page" apparently contains an invalid picture link as follows:
flirig-fldigi.png
since no picture displays for it. Probably the extra "i" between "fl" and "rig".
Thought you might like to know about it and correct it.


Re: FLDigi in LSB mode

Dave
 

Just my opinion, but virus protection software is like buying arson insurance from the mafia.

Dave

On 1/10/21 10:49 AM, Rory Bowers wrote:

The links posted in your email... don't know why they are bouncing but Chrome refuses to go to the site.  Hmmm.  I wonder if my McAfee is preventing it?  No biggie Dave, like I said I know where to find it.
73,
Rory, K5CKS

On Sun, Jan 10, 2021 at 10:46 AM Dave <w1hkj@...> wrote:
I can open the links from the winfldigi.groups.io page.  Which one(s) are giving you trouble?  Did you refresh your browser page?

Dave

On 1/10/21 10:40 AM, Rory Bowers wrote:
The links are bouncing Dave, but I know where to find them.  Thanks!
Rory, K5CKS

On Sun, Jan 10, 2021 at 10:36 AM Dave <w1hkj@...> wrote:
Please download, install and test:

Sun Jan 10 10:19:00 2021 -0600  alpha  1.3.53.17

  FT847
    * add get_modetype

  macOS serial ports
    * update serial port detection function

  PowerSDR
    * Added PowerSDR transceiver
      * compatible with Thetis

  Version 1.3.53

Also suggest you use the latest alpha posting for fldigi (4.1.15 is a bit out of date).

73, David, W1HKJ


On 1/10/21 9:58 AM, Rodney via groups.io wrote:
I have been helping my brother set up FLDigi on his FT-847. We recently noticed that his rig was not suppressing the USB carrier. While trying to solve this, I decided to have him try the program in LSB mode and the carrier is suppressed. 
 
I am able to have a QSO with him in LSB, but his waterfall frequency and Freq: (above the call) is showing carrier frequency plus 1500. But he is correctly transmitting on carrier frequency minus 1500. He is using FLRig for rig control.
 
So I am not sure if there is a setting that I am missing for him or what. I have an IC-7100 and do not have this issue.
 
We are both using FLDigi ver 4.1.15 and FLRig ver 1.3.50.
 
Thanks
73 - Rodney - N3QLB




Re: FLDigi in LSB mode

Rory Bowers <k6cks01@...>
 

The links posted in your email... don't know why they are bouncing but Chrome refuses to go to the site.  Hmmm.  I wonder if my McAfee is preventing it?  No biggie Dave, like I said I know where to find it.
73,
Rory, K5CKS

On Sun, Jan 10, 2021 at 10:46 AM Dave <w1hkj@...> wrote:
I can open the links from the winfldigi.groups.io page.  Which one(s) are giving you trouble?  Did you refresh your browser page?

Dave

On 1/10/21 10:40 AM, Rory Bowers wrote:
The links are bouncing Dave, but I know where to find them.  Thanks!
Rory, K5CKS

On Sun, Jan 10, 2021 at 10:36 AM Dave <w1hkj@...> wrote:
Please download, install and test:

Sun Jan 10 10:19:00 2021 -0600  alpha  1.3.53.17

  FT847
    * add get_modetype

  macOS serial ports
    * update serial port detection function

  PowerSDR
    * Added PowerSDR transceiver
      * compatible with Thetis

  Version 1.3.53

Also suggest you use the latest alpha posting for fldigi (4.1.15 is a bit out of date).

73, David, W1HKJ


On 1/10/21 9:58 AM, Rodney via groups.io wrote:
I have been helping my brother set up FLDigi on his FT-847. We recently noticed that his rig was not suppressing the USB carrier. While trying to solve this, I decided to have him try the program in LSB mode and the carrier is suppressed. 
 
I am able to have a QSO with him in LSB, but his waterfall frequency and Freq: (above the call) is showing carrier frequency plus 1500. But he is correctly transmitting on carrier frequency minus 1500. He is using FLRig for rig control.
 
So I am not sure if there is a setting that I am missing for him or what. I have an IC-7100 and do not have this issue.
 
We are both using FLDigi ver 4.1.15 and FLRig ver 1.3.50.
 
Thanks
73 - Rodney - N3QLB



Re: FLDigi in LSB mode

Dave
 

I can open the links from the winfldigi.groups.io page.  Which one(s) are giving you trouble?  Did you refresh your browser page?

Dave

On 1/10/21 10:40 AM, Rory Bowers wrote:

The links are bouncing Dave, but I know where to find them.  Thanks!
Rory, K5CKS

On Sun, Jan 10, 2021 at 10:36 AM Dave <w1hkj@...> wrote:
Please download, install and test:

Sun Jan 10 10:19:00 2021 -0600  alpha  1.3.53.17

  FT847
    * add get_modetype

  macOS serial ports
    * update serial port detection function

  PowerSDR
    * Added PowerSDR transceiver
      * compatible with Thetis

  Version 1.3.53

Also suggest you use the latest alpha posting for fldigi (4.1.15 is a bit out of date).

73, David, W1HKJ


On 1/10/21 9:58 AM, Rodney via groups.io wrote:
I have been helping my brother set up FLDigi on his FT-847. We recently noticed that his rig was not suppressing the USB carrier. While trying to solve this, I decided to have him try the program in LSB mode and the carrier is suppressed. 
 
I am able to have a QSO with him in LSB, but his waterfall frequency and Freq: (above the call) is showing carrier frequency plus 1500. But he is correctly transmitting on carrier frequency minus 1500. He is using FLRig for rig control.
 
So I am not sure if there is a setting that I am missing for him or what. I have an IC-7100 and do not have this issue.
 
We are both using FLDigi ver 4.1.15 and FLRig ver 1.3.50.
 
Thanks
73 - Rodney - N3QLB