fldigi can be resized if viewing is difficult for a person who is sight disabled. This technique is primarily for Windows. I have tested only on Windows 7. Select fldigi as the active

I have been using FLDIGI 4.1.09.18 in the CQ WPX contest and have been experiencing macros that repeat by them selves every once and a while. Has anyone else seen this happen? Thanks, Larry 

I have found that every time FLDIGI is closed and reopened, I have to go to the contest screen and reset the counter to the proper number that N3FJP is at, it will show the proper number in

It works fine as before in fldigi 4.1.09.05 alpha with chars such as Å Ä Ö. With 4.1.09.18, sending ABC-ÅÄÖ-DEF results in ABC-pause-DEF, but all chars are written in red in both TX and RX

Funny, as an observation, if I run the USB CAT virtual com port via VSPE com port splitter to IC-7300, instead of direct to IC-7300, CW chars seems good again with DTR keying. Thus, instead of RigCAT

Thanks, that works Haris. With mode CW-R the tone follow VFO direction, and I switch modes (and swap macro file also) with a macro button. Seems I can skip the IC-7300.xml file change as you say. 73

I have a <LOG><INCR> macro and it saves the contact and increase the counter. No problems for years. Haris SV1GRB Στις Κυρ, 9 Φεβ 2020 στις 6:45 μ.μ., ο/η Jim Ruff via Groups.Io

I'm running the WPX RTTY contest and every time I log a contact the serial # won't advance. I've tried logging using the logging button, the macros that I created "log/increase" and "increase". None

One minor addendum/info to the below.  When I start up the log fresh the S# is 000.  If I send a qso from this then I send 000 as the serno.  But once I save the contact with <LOG>, FLDIGI

Last year, I tried using FLDIGI with N3FJP's CQ WPX contest log.  I had a problem where sometimes the serial number of the RTTY contact would increment in the N3FJP log but not in FLDIGI.  The next

Did you try to set "USB" in "SET/Function/CW Normal side" menu? This reverses the logic without changing anything in the xml file. Haris SV1GRB Στις Κυρ, 9 Φεβ 2020 στις 4:51 μ.μ.,

Is there a logic that reverses the QSY button freq change direction for mode CW-R compared to CW mode (on IC7300)? - And is that correct? 7300 mode CW seems to use lower sideband (suitable for hand

While looking for a solution to the CW DTR keying problem with IC-7300, I use WinKeyer usb stick to key the rig in CW mode. That works fine, but can not get Farnsworth keying to work, neither from

Greg! MANY THANKS for all the testing and thinking on my topic! The latest macro you crafted works flawlessly! I think I get the logic too... only one TX command and the use of the ! to keep the

Since .18 worked for you, I'd go back to it. I always keep the previous version available just in case the new one has bugs.

Hi Bo, First of all, are you using the latest alpha version, 4.1.09.18? If not then I suggest you do and see if it helps. Some important changes were made that may make a difference for you.

What I have noticed, Is that when I get above about 20 words per minute the spacing between letters is longer. It all sounds good from about 12 to 19 words a minute above that seems like there’s an

With my former rig FT-991, DTR CW keying worked so good with well formed Morse sent (fldigi 4.1.09.05) with rig in CW mode. With my IC-7300, DTR CW transmission is uneven with incomplete or skipped

That’s good news. There may be a lack of sigs other than RTTY this weekend for sure. I won’t be doing the contest, but would love to see you Thursday eve. on the net if you can work it

Hi all. Does anyone have a FT-891 XML file for Rigcat? I know the FT991 is on Source Forge. I know the FT991 can be modified for the FT 891. Just wondered if anyone has a copy of the xml xml . Thanks