Continuing the discussion of the <TUNE:NN> macro: I can not get the proposed macro to work, even after studying the macro order text file, and trying variants. RIGCAT commands get sent at wrong time

One of the methods I use to decrease the periodic resource hogging is to disconnect the Ethernet and/or Wireless Connectivity. On several occasions on Windows 7 and Windows 10 boxes I have severed

Have you looked at the Windows Resource Monitor? Just type in Resource Monitor in the search window in the lower left of the Windows screen. Then take a look at what is consuming all the CPU, disk

It’s squelch for the signal browser. Check out the manual, section 6.18. 73, Cliff, AE5ZA

Question about winfldigi: At the bottom of the Signal Browser window, there is a slider bar. What is it's purpose? I couldn't find it in the manual. Ken

OH.... try this. Set the waterfall speed to PAUSE (That stops it and frees up memory that would be needed to paint the waterfall). Barry k3eui

Questions: How much memory is available for FLDIGI with an older Win 7 computer with Win 10 installed? Win10 can bog down an older computer with insufficient memory and slow processor. Is the

Posted at http://www.w1hkj.com/alpha/flrig/ README.txt flrig-1.3.48.04.tar.gz flrig-1.3.48.04_i386.dmg flrig-1.3.48.04_setup.exe

A member of our disaster communications group has done a clean install on a Win 7 laptop was updated to Win 10. He's got FLDIGI, FLWRAP and FLMSG running fine...but. Though he's sending and receiving

Hi All, FLDigi 4.1.00 transferred the state to N3FJP fine, but I have been able to duplicate the problem with FLDigi 4.1.08. FLDigi is writing United States in the Country field (my software expects

Hi All, I just ran a test with FLDigi 4.1.00 and I could not duplicate the problem of the state not transferring to CQ WW RTTY. As always, you do have to log the contact in FLDigi before it transfers

Yeah the 991a is really well supported. I’ve defined a few Cmd buttons for doing things like sending the command to change microphone source from mic to rear (so i can use my pc microphone and

These are the settings I use without any problems.. Make sure your port speed is the same in the radio and use the lesser of the two port numbers from Silicon Labs in the port pulldown. Hit INIT,

Doesn't the FT-991 entry work? What version of FLRig are you running? de Mike W9MDB On Tuesday, October 1, 2019, 10:46:29 PM CDT,

Hi Dave, As a new owner of an FT-991A, I was a little curious as to why my rig is not supported in the FLRIG rig list.?? Also, can you give me a clue as to why I can't key the rig through the USB

Echostar 9 So, there is a proposal out from ORI (Open Resource Institude) for rented bandwidth on Echostar 9 at 121 deg West. All the FLdigi modes will be able to be repeated by it. The uplink is via

Frank, The one cool thing about Fldigi is how W1HKJ gave us shortcuts to the file system from within the program :-) 73, Ron NY3J On 9/30/19 8:04 PM, Frank wrote:

Thanks, Ron. I did a little searching and found that, at least on my Win 7 system, the path is: c:\Users\[username]\fldigi.files\temp\analysis.csv

Frank, In Fldigi select File, Folders, Fldigi config. Then double click the temp folder and the alnalysis.csv folder should be there. 73, Ron NY3J On 9/30/19 7:42 PM,

I've seen it mentioned that the analysis.csv file saved in Frequency Analysis mode is stored in the \temp directory. However, I don't find a \temp directory under either c:\ or under the fldigi