Hello All, I have a Peco SL-U8363 and (2) PECO PL-10 On the back of the Double Slip package They show one PL10 having Track Power IN To Right Hand Frog Track Power In the other PL10 To Left Hand Frog

Greetings, Does anyone know where to buy DPDT latching push button switches, preferably in bulk? Thanks, Michael Boyle

I am installing a Walthers 90’ Cornerstone Turntable on my third level. I have the turntable placed. Leveled off. I have the wiring on the turntable done so my turn table now has power. I added the se

As I build out my layout with the great help from these forums, I've run into the problem of having too few Switch 8 MK2 decoders. So far my system is 95% NCE with the 5amp Power-Pro, 3 AIU's, 3 Switc

--I have an older Walthers 130' dc turntable received as a gift 12 years ago, brand new, just now installed in new layout. The indexing is not working well at all, moves a bit then stops. I'd prefer t

HELP!! I am a newbie and have a question about how to properly connect and layout buss wires when there are electrical blocks or districts on the layout. I have two tracks on my layout and a buss wire

Are there any pros or cons for using Speaker Wire vs using individual wires twisted together, 3 turns per foot, for long runs of your power busses. These would not be the Power Buss wires that track f

Hello all. What are your thoughts on using Romex for the bus wires? Pros and Cons. I like the fact that it's solid copper vs stranded. Thanks.

Hi, I'm getting ready to wire the AR-1 as follows: AR-1 INPUT +/-: BLUE POWER DISTRICT FOR ALL TT RAYS AR-1 OUTPUT +/-: TABLE TRACK INPUTS Will the AR-1 reverse the polarity of the TT TRACK to match t

I finally just finished installing my two HO tracks and associated buss lines and the connections to the Digitrax controller. Three of my four electrical blocks are operating fine but one of the block

I found an AC-DC wall wart in the garage. It's 120V, 11W and output is 12V, 400mA. It's from an old phone charger. What can I use it for? Thanks for suggestions. Richard

Our club needs to purchase additional NCE ProCab wireless units (4) and wired units (3). the wireless units we purchased previously I converted to rechargeable batteries and also purchased a charging

I am looking for someone in the East Dallas, Richardson, Garland, and/or Mesquite Texas area that is into N Scale and would help me out to finish my N Scale Layout. I can be contacted at joannplano200

Hi all. I.m a complete novice to dcc. My question is; on a layout with two separate loops, can you connect two droppers, from the outside rails together before conneccting them to the main bus? I have

A friend of mine bought a loco at a swap meet that looks like it has a decoder, but I can't wake it up. There is only one identifying mark on it--'CVP'. Can anybody help identify? Thanks, Greg Harter

I am building a relatively simple O scale layout where I have a reversing loop within a circular mainline. It currently reverses trains in one direction using a PSX-AR in the reversing section. Ideall

The following photos have been uploaded to the One reversing loop to support reversing in both directions off the mainline? album of the w4dccqa@groups.io group. SharedReversingLoop3.jpg By: wyantj01@

Good Morning, I have a reverse loop (picture uploaded) that is not working correctly. I am using a Digitrax PM42 with district 2 setup as a reversing loop. The train is traveling right to left on the

The following files and folders have been uploaded to the Files area of the w4dccqa@groups.io group. /Reverse Loop.pdf By: Tom Anderson <tanderson@...>

Don Weigt <dweigt47@...> updated the album Car lighting keep alive cap: Greg Harter's passenger car lighting board with added capacitor. Greg reports lighting is constant for more than five seconds af