I have loaded a file named U_Turn=20190511a_1.pdf into the files section. I believe the gaps and the connection using a PSX-AR reverser will function as expected. One train at a time is the anticipate

I have been told that when gaping rails for isolation that the left rail gap should be in line with the right rail gap. However, the documentation for the reversers, PSX-AR say that they should be off

Greetings all! I just finished the the benchwork and beginning the track laying and wiring on my new layout. HO Scale, using NCE DCC (PH-PRO 5AMP). In the photo linked I've marked with red lines where

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the w4dccqa@groups.io group. File: U_Turn=20190511a_1.pdf Uploaded By: emrldsky Descripti

I have a DC loco that has 4 LEDs front and rear. There are two white LEDs and two red LEDs at each end. When running forward in DC mode the two white LEDS light up and two red LEDs in the rear light u

In other posts & forums, I had participated in discussions involving this subject. And although not directly related to newbies/nocices, is of importance to modelers. Radio Shack may be hard to locate

I'm working on a Genesis F3A with Highliners shell that had a screwed up decoder. In fixing it, I needed to pull out the Athearn board to put in a new Tsunami decoder. This leaves me with the question

well i give up on bachmann its to much to try and make it dcc i was looking at peco tracks and turnouts code 75 i dont know much about it and atlas tracks code 75 ho sccale can i mixed atlas and peco

Hi Gang: Model Railroad Hobbyist Magazine just published my article about Jim Behling's Drop Bridges. You can view the video here: https://www.youtube.com/watch?v=UeSBft9nRDo&feature=youtu.be Hope you

All, I have recently added more rail anchors to my website. If you want to refer someone to a specific topic in my website and you see a rail cross section, just click on it. At the top of your browse

Sending Back to Bachmann... Over and Over Again...Expecting a Different Result..is my definition of Insanity in Model Railroading. Yet it is done all the time. Not Me... I purchased several N Scale At

I am new to this group. Just have a simple question. If a buss wire "should" be AWG14. Would two AWG 20's twisted/soldered together be sufficient. All the stuff I see is so complicated and overwhelmin

i was wondering is it possable to run dcc on my ez track (silver/nickle) and what i need to buy

>>> DCC especially Sound DCC requires Clean and perhaps bright and shiny to that upper quadrant between the rails where the flanges glide over. ==== So.... Here is what you may not agree with...but is

This may be the dumbest question I've ever had. The PECO Insulfrog. I have them not wired, not in any way. They are connected to flex track only by joiners. (I may solder them in the future, but for n

I just finished a new layout and am a novice at best. I have had trouble with shorts but thought I had it finished when the command light went on. However, I cannot get either of my engines to run or

I am new to your group and to model railroading. I am currently laying track, N scale, and need help with the multitude of Peco turnouts. As typed int he subject, I am using all Peco N Scale Code 55 e

Don Vollrath's advice for a simple test light for DCC can now be found on my website at: http://www.wiringfordcc.com/track.htm#a29 Allan Gartner Wiring For DCC

Hi All, I'm new to DCC (never used before and haven't yet) and new to N Scale using Kato Unitrack and #6 turnouts. I plan to use Digikeijs DR5000 (https://www.digikeijs.com/en/dr5000-adj-dcc-multi-bus