The following photos have been uploaded to the Charles updated layout album of the w4dccqa@groups.io group. 72D93B91-FE5C-4885-8DEC-A60889B1BD50.jpeg By: Charles Cauble <drbeetlebaum@...>

Hello, I've purchased a new Bachmann C-19 G-Scale DCC wired locomotive. From what I've read, the loco is DCC plug-n-play wired. I would like to get advice & options for both the DCC controller & decod

The following photos have been uploaded to the CROSSOVER AUTO REVERSE album of the w4dccqa@groups.io group. XOVR 1 AR1 .jpg By: Lawrence Varady <mrmrsv5049@...>

Like many others seem to be i am pretty new to DCC, having been in G scale for many years and then inactive for a number of years. I think i have read the answer to my question several times. Unfortun

I discovered recently that a Walthers E7 diesel that had been running without issue suddenly was shorting out a power district. Close inspection showed no obvious problem in either of the 3-axle truck

Hello Everyone, I would like to have an on off switch on my control panel for my storage tracks. Is there a way I can have green LED on for power and red LED showing track is not powered. With many so

I realize that in a previous discussion we covered most of the questions about auto-reversing segments in DCC. And I apologize if this is redundant. I understand that an AR segment must be longer than

I have to apologize cause this is a bit long, but here goes. So, here is my multi attempt frustration. I just recently purchased a used Proto 2000 GP30 DC locomotive. Nothing wrong with it running. It

Lawrence Varady 2:32pm #196094 I will post photos and would like help on determining how to wire AR1'(s) for my layout. I am using an Atlas 2564 DEAD FROG crossover. I will not be running any lighted

Hi I am currently planning a new layout with a large, off-scene, double ended staging yard. I am using DCC Concepts Cobalt Alpha products - switch machines, control panel switches etc. My layout will

I want to put "soft" Styrofoam base under single track mainline on my around the room 2' shelf HO layout. All I can find w/in 100 miles is 3/4" insulation board wrapped on both sides w/foil. Can't use

The following photos have been uploaded to the DBL XVR AUTO REVERSERS album of the w4dccqa@groups.io group. TT AR1 10-21-21 .jpg By: Lawrence Varady <mrmrsv5049@...>

Is this wiring correct for the dbl xvr shown? Any comments appreciated. Thx

Hello All, I have one feeder for both loops Each Loop has a TAM Valley Dual Frog Juicer setup as a Auto reverser. The reverse loops are working fine. My question is On my one reverse loop I have a tur

I rebuilt one of my single crossovers using peco unifrog turnouts. The switch machine is a tortise and the controller is a digitrax ds 64. After installing the cross over, I test ran several locos. Th

All, I have made a couple of additions to the Wiring for DCC Website: 1. Link to Evan Designs. They provide a wide variety of miniature LEDs useful to the model railroader. 2. The new Walthers DCC Fri

I just read Allan's column in MRR sept. I am gald I did. What blow to my plans. Now I have a cunundrum. I have laid all my track. I am using DCC specialties PSX, PSX-AR and Frog -ARs. I also planned t

Hi - On this one-line diagram Jim shows the autoswitch wired to a programming track with an isolation track. I understand that the purpose of the isolation track is to keep you from accidentally drivi

Hello All I have a reverse Loop and I setup two blocks in the Loop for signaling All trains can run in either direction thru the loop with now problem. Today on the two feeders I connected my NCE BD20

Tom Grassi <trgrassijr@...> added the album BD20 Reverse Loop: Need help with wiring a Reverse Loop for block detection The following photos have been uploaded to the BD20 Reverse Loop album of the w4