Date   
Re: Current through the soldering iron tip

Dennis Cherry
 

No matter how good your soldering is and has all the safety features needed, if you use a 3 prong to 2 prong adapter then it is no better than a cheap soldering iron. 

The Safety ground has a purpose, your house wiring has to have the 3rd wire (Ground) also and have a copper stake in the ground connected to the third wire.

The White wire is called neutral and is only used as the return wire for 110/120 VAC not a safety ground.

Dennis

Re: Current through the soldering iron tip

JBJudy
 

This comment causes me to ask for a clarification ............

"Thank you for the heads up.  I will test my Weller ( a 51 if memory serves – or fails) tomorrow.  If it fails, I will continue to use for general soldering – ie working on turnouts and general wiring, but will have to find a substitute for decoder work.

Greg"


Very interesting topic. Sounds like the issue is only when soldering the decoders. Is the "leaking voltage" not harming an engine on the track when soldering feeders?
JB Morrow

Re: Current through the soldering iron tip

Charles Brumbelow
 

An older house, originally wired with two rather than two plus ground, may have some/all outlets with three prongs where inside the box the ground terminal is connected to the white (neutral) wire. And the three to two adapter which fastens to the screw holding the cover on is worse than useless unless metal conduit was used throughout the building. 

Charles 




On Wednesday, June 12, 2019, 7:27 AM, Dennis Cherry <dbcherry@...> wrote:

No matter how good your soldering is and has all the safety features needed, if you use a 3 prong to 2 prong adapter then it is no better than a cheap soldering iron. 

The Safety ground has a purpose, your house wiring has to have the 3rd wire (Ground) also and have a copper stake in the ground connected to the third wire.

The White wire is called neutral and is only used as the return wire for 110/120 VAC not a safety ground.

Dennis

Re: Current through the soldering iron tip

Denny Anspach
 

 ESD SAFE reportedly is the sign that the iron is grounded and labeled to be safe for CMOS and similar electronic work. My current Weller is so labeled, and apparently it is the same iron also  commonly used in the nearby gigantic Intel   plant (California location).

Denny

Denny S. Anspach MD
Okoboji, IA

Denny S. Anspach MD
Sacramento CA 




Re: Current through the soldering iron tip

Greg Smith
 

Thank you for the info.  Still, I will test it the next time I fire it up.  Has generated some conversation on the forum.  My shop, wired by myself, does have a separate ground wire and all receptacles are new three prong plugs.  So that should not be an issue.
 

From: Denny Anspach
Sent: Wednesday, June 12, 2019 3:31 PM
To: w4dccqa@groups.io
Subject: Re: [w4dccqa] Current through the soldering iron tip
 
ESD SAFE reportedly is the sign that the iron is grounded and labeled to be safe for CMOS and similar electronic work. My current Weller is so labeled, and apparently it is the same iron also  commonly used in the nearby gigantic Intel   plant (California location).
 
Denny
 
Denny S. Anspach MD
Okoboji, IA
 
Denny S. Anspach MD
Sacramento CA



 

Power Boosters

Obeeone
 

Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Current through the soldering iron tip

Mark Cartwright
 

As from a previous thread...(deleted by management)
>>> I am a big proponent of a properly wired AND Grounded (with pound in ground 10' spikes) 
BEFORE 
Beginning any phase of DCC ...
be it wiring the layout.
plugging in the DCC controller..
And YES...
Using a Three Prong Ground Receptacle which has Not just been hung on the wall for looks
> Even for soldering.
====
In this old house...I found many an outlet which was out of phase (and out of gauge).
:)) Mark

OT...
I just spent more than three grueling days running a new line out to the AC Compressor in 100+ heat.
The wire to that location ?
I don't know....I had cut it previously as I began to simply rip out what I saw as a potential fire hazard.
Since my last posting however...I found a hidden Circuit Breaker Box hidden behind a built in cabinet...only accessible by removing a drawer.
Whose to know?
The wires leading to it...were under gauged and aluminum.  Didn't bother to figure out what it went to...
I removed it immediately.
Oops! It may have connected to the AC Compressor.
I only became seriously motivated when the heat was about to top 99 degrees.
All now successfully replaced. I got AC Again !

Re: Power Boosters

Mark Gurries
 


On Jun 12, 2019, at 5:35 PM, obeeone@... wrote:

Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Simple Answer: They are not designed to be mixed.  There was no DCC standard covering booster compatibility when the standards were developed.  Although there is a standard today, it is to little to late.

It is possible to mix them.  Some, but is gets complicated, special wiring, rules, not supported by manufactures and your on your own for any consequences.

Best Regards,

Mark Gurries
Electrical Engineer
DCC Website & NMRA DCC Clinics: www.markgurries.com



DCC Power Boosters - Mix or Match

ROBERT HULTMAN
 

There's an article in the July 2019 Model Railroader reviewing several different DCC systems.  Suggest reading thru it for some basics.  In general, my impression form the article was No, but refer to the specs for the system-systems under consideration.

Bob Hultman in Brentwood TN

On Wednesday, June 12, 2019, 10:06:38 PM CDT, obeeone@... <obeeone@...> wrote:

Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Current through the soldering iron tip

Max Maginness
 

I did a census of soldering irons on hand

 

Type     

Tip voltage relative to ground

WLC 100 

26 volts

Weller WES D51  ESD

<0.1 volts   (3 wire)     

Archer (Radio Shack )

3 volts

Ungar (about 40 watts)  

6 volts

Weller (35 watts)

40 volts

 

 

 

All were two wire except the WES D51

In no case was the leakage current to ground more than 20 microamps. There is no personal shock hazard but you might not want to touch a hot tip for other reasons anyway.

 

Max

 

From: w4dccqa@groups.io <w4dccqa@groups.io> On Behalf Of Greg Smith
Sent: Wednesday, June 12, 2019 1:18 PM
To: w4dccqa@groups.io
Subject: Re: [w4dccqa] Current through the soldering iron tip

 

Thank you for the info.  Still, I will test it the next time I fire it up.  Has generated some conversation on the forum.  My shop, wired by myself, does have a separate ground wire and all receptacles are new three prong plugs.  So that should not be an issue.

 

From: Denny Anspach

Sent: Wednesday, June 12, 2019 3:31 PM

Subject: Re: [w4dccqa] Current through the soldering iron tip

 

ESD SAFE reportedly is the sign that the iron is grounded and labeled to be safe for CMOS and similar electronic work. My current Weller is so labeled, and apparently it is the same iron also  commonly used in the nearby gigantic Intel   plant (California location).

 

Denny

 

Denny S. Anspach MD

Okoboji, IA

 

Denny S. Anspach MD
Sacramento CA


 

Re: Power Boosters

ronmerrill69
 

No, would not be good 


On Wed, Jun 12, 2019 at 11:06 PM, obeeone@...
<obeeone@...> wrote:
Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Power Boosters

dennisedgar7
 

Hi, I have mixed Lenz and Digitrax.
Just read the instructions.

Dennis

On Thu, 13 Jun 2019 at 05:06, <obeeone@...> wrote:
Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

--
Dennis G Edgar
Lead Auditor  133839
mobile: 083 6470569

Re: Power Boosters

scott toro
 

Yes you can add Bachmann power boosters I’m not sure about other




On Wednesday, June 12, 2019, 5:35 PM, obeeone@... wrote:

Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Power Boosters

vincent marino
 

Theorectically you should be able to because all up to date manufacturers use national standards. However if the boosters you're using have any age and considering how tempimental DCC is, I would recommend single source manufacturer for a new layout. Think about it, if you tracking down a problem you're not going to know if it's a short or a manufacturer conflict. I like to say "never enough time (or money) to do it right always enough time to do it over".


On Wed, Jun 12, 2019, 11:06 PM <obeeone@...> wrote:
Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Power Boosters

whmvd
 

Hi Obie-wan,

Even if you get it working technically (and some combinations should be workable), think of the nightmare when you need advice from a manufaturer because one day something doesn't want to play anymore. As soon as you admit to mixing brands, each will point to the other, and you will be left with no help except for the internet (which isn't bad, but having the manufacturer jump ship *is*).


So my response: better not.
Wouter


On Thu, 13 Jun 2019 at 04:06, <obeeone@...> wrote:
Can anyone help me with this question? I'm re-entering the train scene but I'm asking if I am able to "mix-n-match" brands of power boosters. In other words, say I have an NCE DCC system. Can I add a Bachmann or Digitrax or any other brand as a power booster, or must the power booster be of the same brand system? Can I mix them? Thanx.

Re: Current through the soldering iron tip

 

When soldering feeders on you layout and large circuit boards there is enough leakage to ground to take care of the problem.  Also the track connections of the decoder is the least susceptible to this problem because of the power capacitor that is on the board. The smaller the decoder the greater the risk.

Best Regards,
Ken Harstine

Re: Current through the soldering iron tip

JBJudy
 

I am looking for clarification as I have this Weller unit & it is NOT MARKED ESD SAFE!

Re: Current through the soldering iron tip

Craig Zeni
 

On Jun 13, 2019, at 9:33 AM, JBJudy wrote:

I am looking for clarification as I have this Weller unit & it is NOT MARKED ESD SAFE!
Then don't do decoder or electronic work with it. I wouldn't risk smoking a decoder with a non-ESD safe iron.

Craig Zeni
Cary NC

Re: Current through the soldering iron tip

Don Vollrath
 

ESD Safe is not the exactly the same as current leakage or as simply grounding the tip of a soldering iron. There is as special spec and requirements for it to protect sensitive electronic equipment.... like microprocessors and amplifiers used inside decoders. Remember seeing sparks from your fingers when handling wool sweaters in dry humidity conditions?  See https://en.wikipedia.org/wiki/Electrostatic_discharge.
BTW - When you use a grounded soldering iron make sure that whatever thing you are soldering to is NOT energized. Otherwise you are creating a direct path for current to flow from whatever source it is connected to by touching it with a grounded soldering iron.
DonV 
  

Re: Current through the soldering iron tip

Michael Rozeboom
 

On 2019-06-13 9:33 a.m., JBJudy wrote:
I am looking for clarification as I have this Weller unit & it is NOT MARKED ESD SAFE!


Then it is not.  ESD safe units are identified with the ESD safe symbols.  Older units have the three prong plug, and they are not ESD safe.



--




Michael Rozeboom