Hello, the TIMEOUT function in the ModuleParrot dosen't seem to work with high number. From what I see, the value is in seconds. If I set the value at 60s, the TIMEOUT will proceed correctly after a m

Hello Tobias! SvxLink can not play audio files for the Reflector logic This happens if another language localization is set. For example, Ukrainian "uk_UA". English "en_US" - not installed. It is poss

Hi Group, I have an SVXLink card installed into an Icom IC-RP1510 VHF repeater. I have managed to get it to transmit it's ID as I wanted both long and short. I am struggling with getting the 77Hz tone

Hello! I want to make a Bridge with EchoLink in SvxReflector. How to make Reflector remain in the assigned group "TG #112", and not go to "TG #0"? Regards, Volodymyr

I am running SVXLINK on a raspberry PI 2. Setting it up was a pain, but I finally got everything to work by using an optocoupler relay on a GPIO pin to control the PTT. When I tested the link over a s

Dear group, I am hunting a bug with latest svxlink when used with alsa plugequal plugin. The svxlink service is started (and stopped) by systemd at boot time. Svxlink starts fine and does not complain

I've finally got echolink working for svxlink. But people are complaining that the "repeater" part isn't working. People can do echolink on the raspberry pi, but when then just talk simplex on the rad

Hi, G4KLX adds support for FM Analog to MMDVM and MMDVMHost. We need in future add small part program SVXGateway which will allow connecting MMDVMHost with SVXReflector. https://groups.io/g/OpenDV/top

hi group, I upgraded my internetspeed a litte. But unfortuneatly my ISP cut of IPv4. So my question is. Does svxlink especially echolink support IPv6? Or is there something I need to do to get v6 work

Hello Tobias, I use SVXLink with TG's. What I see is that also with TG with different priority if an highter priority TG is request from local RF receiver while one with lower priority is active the r

Hello! Does anyone use SvxPortal v.2.1? How to configure it correctly? Regards, Volodymyr

Hi Tobias, I asked myself why the ToneDetector for CTCSS is initialized with fixed parameters within the RepeaterLogic in contrast to the initialization within the Rx object. In RepeaterLogic: if (! r

Hi, If you have multiple SvxLink nodes to maintain it may require a lot of time to maintain them all when the number grows. Using manual methods also can be very error prone. The answer to this is to

Hello! I want to use individual files to the actual time of SvxLink. How to change "locale.tcl" so that time files are in folder "Time"? Regards, Volodymyr

Hi all, I'd like to be able schedule announcements at set times (like a cron job) say at 1925 before the 1930 net starts .... much the same way I can play a wav with the long ID message at the top of

REJECT_INCOMING=^(.*-[LR])$ ACCEPT_INCOMING=LIST OF CALLSIGNS SEPERATED BY A PIPE REJECT_OUTGOING=^()$ #ACCEPT_OUTGOING= REJECT_CONF=1 People not on the ACCEPT_INCOMING are still able to use the repea

DEFAULT_TG=112 TG_SELECT_TIMEOUT=3600 60min. Is this a normal solution? --- Оригінальне повідомлення --- Від кого: "Volodymyr" Дата: 16 квітня 2020, 13:34:06

hello guys, I would like to stream my local svxlink station according to this : https://github.com/sm0svx/svxlink/wiki/StreamingAudioToInternet I dit all but when I start svxlink I've got this : Sun A

Hallo, in the man page of svxlink.conf 19.09 there is a PTT_HANGTIME conf variable. It says: ..."When the transmitter is ordered to stop transmitting, the tone is immediately turned off, causing the s

I have just put up svxlink, on a Raspberry Pi, with a USB-Signalink, using VOX. The echolink is working ok, but there is one lingering problem with a radio keying up on the frequency. According to som