You may remember a struggle I was having with some traces shorting out. As it turns out, I had converted a library file for a 28 pin DIP from having little round pads to the elongated type which I fin

[pcbgcode:master] New Comment on Issue #1 Use small endmill to mill holes of various sizes By MARIOBASZ: This is good. I think a good option is to choose one (or more than one) tool diameter to drill,

[pcbgcode:master] New Issue Created by MARIOBASZ: #2 Milling with 3 bits I John, here I show you what I have done using 3 bits: 0.10 - 0.7 - 3.0 and here I have implemented: I have run pcb gcode 3 tim

[pcbgcode:master] New Issue Created by MARIOBASZ: #2 Milling with 3 bits I John, here I show you what I have done using 3 bits: 0.10 - 0.7 - 3.0 and here I have implemented: I have run pcb gcode 3 tim

Hi, I'm new here, I think it would be a good option. Can you implement it? I have little knowledge of programming, although I have advanced with a complement to implement it in BCNC, but it is not the

Hi! I have to make a pcb where are power traces also beside signal traces. The power traces are for the main AC/230v which are going into a relay then out on two outputs. Everything is fine, but! I wi

I now have a couple of years and dozens of successful boards cut on my 6040 router - and some bad ones too. Boards are all cut from 2 1/2 x 4 inch single side pcb stock. I made a jig for drilling hole

Hi! I'm new here, so pls forgive me if I post this into the incorrect place... Here is my problem: I used Eagle 9.2.0 until a few days. After AutoDesk released the new update 9.2.2 of Eagle I updated.

Just installed eagle 7.6 and PCBgcode on win10. The PCBgcode files are in c:\users\jim\documents\ulp\pcb-gcode-3_6_0_4 The directories are set as below. When I try to run PCBgcode I get the message as

hi, i have some problems when i'm running my project. after do the pcb desing i puted to run the ulp and upload to mach 3, this is the problem, because the trajectory not is nothing compare with the d

Hi All, Getting better at my board cutting and soon will make my first board. I have a question I was wondering is there a way I can start up my gcode at a place further into the code ? I have found t

I thought I was getting an understanding of pcbgcode. Attached is a photo of my closest attempt yesterday at the bottom of the copper. I decreased the sizes so that the traces should have been cut cor

Made a schematic and then tried the board. Gave autoroute a go and got a reasonable board. Problem is there are areas I have made errors on both the board and schematic. Trying to undo and go back I n

I have ground planes on both sides of the board. Rtch tool size set to o.3mm. As you can see below there are multiple isolation passes around the drilled hole but only a single pass around the tracks

I have been using Eagle and PCB-Gcode for many years now with good results using a cutter to engrave the PCB traces. For the past couple of days I have been trying a slightly different way of using PC

Hello to group I have been following the milling layer thread and I would like some help. I have never been able to use the milling layer. I place text on my pcb using milling layer 46 I believe I che

hi everyone i'm new at both pcb design and getting print it out. I have a mini cnc plotter to use for printing the layout of pcb design. I have seen videos on youtube guys doing the printing job. But

OK, Got my first board made and all ok. Still need to iron out a few bits but after running the etch file I got my tracks. Thanks to all who offered help with other posts After the first run I had my

I am very familiar with Eagle going clear back to 4.09..I want to use Eagle to make design in .sch for plexiglass cutting and then somehow make Gcode from that..Should I use symbol for the lines/circl

Not sure if this is the correct place or tag, apologies if I am wrong. I feel confident with a little more work ?I can get the boards I design made but there are still some very good boards out there