
Re: @help
#development
It can be found at:
<https://github.com/johnatl/pcbgcode>
Good luck and welcom aboard.
Country
It can be found at:
<https://github.com/johnatl/pcbgcode>
Good luck and welcom aboard.
Country

By
Art Eckstein
·
#8037
·


@help
#development
merhabalar programı indirebilmem için bana yardımcı olabilirmisiniz?
merhabalar programı indirebilmem için bana yardımcı olabilirmisiniz?

By
can.ct200@...
·
#8036
·


Re: Best size end mill for milling perimeter of PCB?
#mill
Hola Mario,
las velocidades son
para trazas 20 (IPM) pulgado por minuto XY, 10 pulgado por minuto in Z
cortar 8 (IPM) pulgado por minuto XY, 6 pulgado por minuto in Z
Hola Mario,
las velocidades son
para trazas 20 (IPM) pulgado por minuto XY, 10 pulgado por minuto in Z
cortar 8 (IPM) pulgado por minuto XY, 6 pulgado por minuto in Z

By
John Ferguson
·
#8035
·


Re: Best size end mill for milling perimeter of PCB?
#mill
John, ¿qué velocidad de alimentación utilizas para las trazas y para cortar?
John, ¿qué velocidad de alimentación utilizas para las trazas y para cortar?

By
mariob_1960@...
·
#8034
·


Re: Best size end mill for milling perimeter of PCB?
#mill
EM3E8010015V 0.0100in. (0.254mm) tip dia., 3flute 15° tapered stub traceisolation bit, 0.020 in. DOC, 1.42 in. (36mm) OAL
This is what I use for routing traces on my 6040. I get them from
EM3E8010015V 0.0100in. (0.254mm) tip dia., 3flute 15° tapered stub traceisolation bit, 0.020 in. DOC, 1.42 in. (36mm) OAL
This is what I use for routing traces on my 6040. I get them from

By
John Ferguson
·
#8033
·


Re: Best size end mill for milling perimeter of PCB?
#mill
We used TULON 3/32" P/N 44093803 when I was employed.
(NEW) Tulon Pacific PCB Router Bits 53300938 Series 5330 3/32" x .405" 39pcs  eBay
$42.95
(NEW) Tulon Pacific PCB Router Bits 53300938 Series
We used TULON 3/32" P/N 44093803 when I was employed.
(NEW) Tulon Pacific PCB Router Bits 53300938 Series 5330 3/32" x .405" 39pcs  eBay
$42.95
(NEW) Tulon Pacific PCB Router Bits 53300938 Series

By
Stephen Muscato
·
#8032
·


Re: Best size end mill for milling perimeter of PCB?
#mill
Later. john
By
John Ferguson
·
#8031
·


Re: Best size end mill for milling perimeter of PCB?
#mill
Thanks all! Appreciate the quick responses.
Thanks all! Appreciate the quick responses.

By
Terry Gray
·
#8030
·


Re: Best size end mill for milling perimeter of PCB?
#mill
John, could you send me the details?
John, could you send me the details?

By
Terry Gray
·
#8029
·


Re: Best size end mill for milling perimeter of PCB?
#mill
Sorry, I missed that fact :)
I use precisebits.com router bits for routing perimeters and internal channels. https://www.precisebits.com/
Dan Staver
Tave Tech Corp.
3130 Hollycrest Dr.
Colorado
Sorry, I missed that fact :)
I use precisebits.com router bits for routing perimeters and internal channels. https://www.precisebits.com/
Dan Staver
Tave Tech Corp.
3130 Hollycrest Dr.
Colorado

By
Dan.Staver
·
#8028
·


the perimeter cutter question
#mill
 Forwarded Message 
Subject: the perimeter cutter question
Date: Sun, 22 Dec 2019 23:19:29 0500
From: john <jferg977@...>
To: pcbgcode@groups.io
Oops,'
There is a photo of
 Forwarded Message 
Subject: the perimeter cutter question
Date: Sun, 22 Dec 2019 23:19:29 0500
From: john <jferg977@...>
To: pcbgcode@groups.io
Oops,'
There is a photo of

By
John Ferguson
·
#8027
·


Re: Best size end mill for milling perimeter of PCB?
#mill
This is what I use for the permiterw,
Amana Tool 51515 SC Spiral 'O' Single Flute, Plastic Cutting 1/16 D x
1/4 CH x 1/8 SHK x 2 Inch Long DownCut CNC Router Bit with Mirror Finish
I use pcbcode
This is what I use for the permiterw,
Amana Tool 51515 SC Spiral 'O' Single Flute, Plastic Cutting 1/16 D x
1/4 CH x 1/8 SHK x 2 Inch Long DownCut CNC Router Bit with Mirror Finish
I use pcbcode

By
John Ferguson
·
#8026
·


Re: Best size end mill for milling perimeter of PCB?
#mill
0.0625 inches equals 1.6mm, I'm going to try, I usually use 2mm.
Vaughn, are you using vacuum table?
I am close to finishing my smart vacuum table version, for low cost, high vacuum and low flow
0.0625 inches equals 1.6mm, I'm going to try, I usually use 2mm.
Vaughn, are you using vacuum table?
I am close to finishing my smart vacuum table version, for low cost, high vacuum and low flow

By
mariob_1960@...
·
#8025
·
Edited


Re: Best size end mill for milling perimeter of PCB?
#mill
Hi Gerry, I use V point mills. 60 Degree normally, but there are also 30 and 15 degree I think. After milling the board, my mill, mills a border. This I then follow to cut the board to size. If I mill
Hi Gerry, I use V point mills. 60 Degree normally, but there are also 30 and 15 degree I think. After milling the board, my mill, mills a border. This I then follow to cut the board to size. If I mill

By
Vaughn
·
#8024
·


Re: Best size end mill for milling perimeter of PCB?
#mill
He was asking about cutting the perimeter.
He was asking about cutting the perimeter.

By
keith3125
·
#8023
·


Re: Best size end mill for milling perimeter of PCB?
#mill
I use the largest size bit I can while keeping it 23 mils smaller than the smallest gap between traces.
Dan Staver
Tave Tech Corp.
3130 Hollycrest Dr.
Colorado Springs, CO 80920
+17193595352 
I use the largest size bit I can while keeping it 23 mils smaller than the smallest gap between traces.
Dan Staver
Tave Tech Corp.
3130 Hollycrest Dr.
Colorado Springs, CO 80920
+17193595352 

By
Dan.Staver
·
#8022
·


Re: Best size end mill for milling perimeter of PCB?
#mill
I use the Precise Bits,Diamond cut router bit, .0625"
Carbide Diamondcut Router Bits
Carbide Diamondcut Router Bits
Solid carbide, diamondcut, router bits. For cutting and shaping of ceramics,
I use the Precise Bits,Diamond cut router bit, .0625"
Carbide Diamondcut Router Bits
Carbide Diamondcut Router Bits
Solid carbide, diamondcut, router bits. For cutting and shaping of ceramics,

By
keith3125
·
#8021
·


Best size end mill for milling perimeter of PCB?
#mill
Maybe a bit off topic but can someone recommend the best size and type of end mill for milling out the perimeter of a PCB?
Maybe a bit off topic but can someone recommend the best size and type of end mill for milling out the perimeter of a PCB?

By
Terry Gray
·
#8020
·


Re: PCB  GCODE ICAN'T OPENPERMISSION DENIED
#eagle
#gcode
put pcbgcode in the documents folder and follow the instructions when you open the script.
put pcbgcode in the documents folder and follow the instructions when you open the script.

By
med2004@...
·
#8019
·


Viewer on Mac
#pcbgcode
Is anyone able to run the viewer on Mojave?
This is what I get if I try to run it by hand.
MacBookPro:~ greg$
Is anyone able to run the viewer on Mojave?
This is what I get if I try to run it by hand.
MacBookPro:~ greg$

By
Gregory Wood <greg@...>
·
#8018
·
