Hi John, I just see, that the code you uploaded to Github seems to actual be V3.6.0.1, as stated in the header portion of "pcb-gcode.ulp". The version I have on my machine is of 2014 (plus my

Hi John, I compared the files on Github to the files I have on my computer, both denoted as V3.6.2.4. I found, that "my" "pcb-gcode.ulp" is at least heavily commented, compared to the one in your

Personally, I'm on some Discourse forums, and on some Discord channels, and they work well, but are a lot of work (well, I know they are non-zero) and I don't know how much return you'd see. Now

I find that I'm doing 2 and 4 layer boards with 100+ pin processors. I'm not sure how pcb_gcode would help in this situation, although if I wanted to, I could at least make

Hi Art, Thanks for checking that out! Happy Birthday! That's quite a milestone. Must be all those years of living right, plus a liberal application of cutting fluid now and then :-) Rest assured, if I

OK, downloaded the zip file and loaded the dir into eagle 6.1 that I useand seems to work just fine. Did some poking around and all seemedfine. Country At 3/2/2022 02:01 PM, John Johnson wrote:

JJ, Will do as soon as I can setup Eagle on my new machine. Had a crash andhave to start all over again. You know how that goes! Country At 3/2/2022 02:01 PM, John Johnson wrote:

1 New Commit: [pcbgcode:master] By John Johnson <john@...>: 0d990f9637d0: This should be 3.6.2.4. Added: docs/.texpadtmp/pcbgcode.aux Added: docs/.texpadtmp/pcbgcode.idx Added:

2 New Commits: [pcbgcode:master] By John Johnson <john@...>: ab618f41ca6e: Not sure why these jars have been removed. Added: .gitignore Removed:

1 New Commit: [pcbgcode:master] By John T. Johnson <JohnAtl@...>: d5f7f8f3ee76: Update README Modified: README 1 New Commit: [pcbgcode:master] By John T. Johnson <JohnAtl@...>: 00a6b58d99bc:

I've been using other forums that run on Discourse.I think they are easier to navigate than groups.io (and Discord), as everything here seems to run together.I think I could set one up on Digital

I just uploaded what should be version 3.6.2.4 to GitHub, and would appreciate anyone who can verify that it works.I had some older files on there, 3.6.0.x. I don't currently have anything set up to

Write it down so next time , if there is, you can see how you solved it.

Hi Bruce Thanks very much for the reply. It seems to be solved and something to do with the GND polygon. I deleted the polygon that was there- redid it and it was back to how I intended..

I believe you need to go into pcb-gcode-setup and tell it which layer to etch, top or bottom only.

Hi Guys This is my first attempt at using Eagle and PCB_Gcode. I have a very simple 12 keypad with smt resistor network. All was going well and Eagle looks good with top layer as expected

Can someone remind me what java I need to run the viewer. Could not find docs on this. I'm using Eagle 7.7 on OSX Big Sur. Eagle works fine and pcb-gcode runs and generates files. just no

The answer is in the pcb-gcode-setup ulp. See below This is my setup for a 0.2mm milling tool (no chemical etching in my work). I set the minimum to less than the cutting tool diameter to ensure a

I am new to Mach 3 setup and commands and I have a question.. Is there a G-code command I can use to populate Tool Table in Mach3 in a way that every tool change the operator can see TOOL DIAMETER in