|
|
Re: Horizon Link 1.3
Maybe it’s a case of choose your battles. It doesn’t seem like Janome is very responsive. Maybe there is a work around someone has found.
|
Maybe it’s a case of choose your battles. It doesn’t seem like Janome is very responsive. Maybe there is a work around someone has found.
|
By
Helen Aarness
·
#28187
·
|
|
Horizon Link 1.3
I copied a link from a previous post.
Faviola, my question is: Are you using HLS Ver 1.2 or do you have the upgrade on your 15000, which should have given you the new version 1.3 of HLS as well?
|
I copied a link from a previous post.
Faviola, my question is: Are you using HLS Ver 1.2 or do you have the upgrade on your 15000, which should have given you the new version 1.3 of HLS as well?
|
By
Cheryl Paul
·
#28186
·
|
|
Re: Horizon Link Ver 1.2 not printing design onto template
Whenever I print templates using the Layout mode of HLS I have the problem where it won’t print all the pieces. Generally it’s the center sections in the Layout. I’ve reported it to Janome and
|
Whenever I print templates using the Layout mode of HLS I have the problem where it won’t print all the pieces. Generally it’s the center sections in the Layout. I’ve reported it to Janome and
|
By
favymtz
·
#28185
·
|
|
Re: Horizon Link Ver 1.2 not printing design onto template
I have it fixed, thank you!
|
I have it fixed, thank you!
|
By
Therese Kaun
·
#28184
·
|
|
Re: Horizon Link Ver 1.2 not printing design onto template
Please help. Having an issue on my Jenome Memory Craft 6500. The feed dogs message is saying the feed dog is down, but it isn't. I have taken apart and cleaned, but can't get the feed dog up.
Also,
|
Please help. Having an issue on my Jenome Memory Craft 6500. The feed dogs message is saying the feed dog is down, but it isn't. I have taken apart and cleaned, but can't get the feed dog up.
Also,
|
By
Therese Kaun
·
#28183
·
|
|
Re: Horizon Link Ver 1.2 not printing design onto template
Have you tried printing out some other document that doesn’t go thru horizon link that has designs and text that uses both color and black ink? Maybe your printer cartridges need to be replaced. I
|
Have you tried printing out some other document that doesn’t go thru horizon link that has designs and text that uses both color and black ink? Maybe your printer cartridges need to be replaced. I
|
By
Vikki Youngmeyer
·
#28182
·
|
|
Re: Horizon Link Ver 1.2 not printing design onto template
Judy,
Never had this happen. Do you see your design in print preview? If you select Printer properties, does it have outline checked?
|
Judy,
Never had this happen. Do you see your design in print preview? If you select Printer properties, does it have outline checked?
|
By
Ceil J
·
#28181
·
|
|
Horizon Link Ver 1.2 not printing design onto template
I have used Horizon Link on my MC12000 for 7 years printing out color designs on vellum paper. Then yesterday, when printing, it will print the header and footer, gridlines and crosshairs but no
|
I have used Horizon Link on my MC12000 for 7 years printing out color designs on vellum paper. Then yesterday, when printing, it will print the header and footer, gridlines and crosshairs but no
|
By
Judy Albert
·
#28180
·
|
|
Re: Thread loops on bottom of fabric
Jim, as always, I very much appreciate your assistance (and love your humor). It will be a month or so before I can take my 15000 in for maintenance and until then, I will be sewing on a slower
|
Jim, as always, I very much appreciate your assistance (and love your humor). It will be a month or so before I can take my 15000 in for maintenance and until then, I will be sewing on a slower
|
By
Sheri-A
·
#28179
·
|
|
Re: Thread loops on bottom of fabric
Thank you.
Sent from the all new Aol app for iOS
|
Thank you.
Sent from the all new Aol app for iOS
|
By
ladybug35186
·
#28178
·
|
|
Re: Thread loops on bottom of fabric
I was having the same problem and it turned out that some small spring was broken and it was causing the thread to catch and make a loop.
Diane Bacon
|
I was having the same problem and it turned out that some small spring was broken and it was causing the thread to catch and make a loop.
Diane Bacon
|
By
Diane
·
#28177
·
|
|
Re: Thread loops on bottom of fabric
Coincidentally we just went through a similar problem with Diane's 15000. There were 3 small problems, the final solution being to service the machine. It had not been done in the past 4 years or
|
Coincidentally we just went through a similar problem with Diane's 15000. There were 3 small problems, the final solution being to service the machine. It had not been done in the past 4 years or
|
By
Jim Stutsman
·
#28176
·
Edited
|
|
Thread loops on bottom of fabric
I started seeing small loops on the bottom side of my fabric. I have changed the following with no luck: thread, bobbin, needle, and bobbin holder. I have thoroughly cleaned my machine. I have
|
I started seeing small loops on the bottom side of my fabric. I have changed the following with no luck: thread, bobbin, needle, and bobbin holder. I have thoroughly cleaned my machine. I have
|
By
Sheri-A
·
#28175
·
|
|
Re: Horizon Link Suite 1.31 confusion
There is a slight disconnect in the version numbers. The "suite" top app does not show the same version as EmbLink, but as long as it is 1.3x (x can be 0 or higher), you are updated to the correct
|
There is a slight disconnect in the version numbers. The "suite" top app does not show the same version as EmbLink, but as long as it is 1.3x (x can be 0 or higher), you are updated to the correct
|
By
Jim Stutsman
·
#28174
·
|
|
Horizon Link Suite 1.31 confusion
Hi. I watched a new video today from Anne Hein in the Janome sewing classroom and wanted to do what she was doing on her 15000 in HLS. I really didn't see all the options she was using on the
|
Hi. I watched a new video today from Anne Hein in the Janome sewing classroom and wanted to do what she was doing on her 15000 in HLS. I really didn't see all the options she was using on the
|
By
Ceil J
·
#28173
·
|
|
Re: MC15000 beeping at me
Thank you for your help. Although I tried turning the machine off and on again a couple of times, and it did not help, leaving it overnight seems to have fixed the problem. Thanks for the tip about
|
Thank you for your help. Although I tried turning the machine off and on again a couple of times, and it did not help, leaving it overnight seems to have fixed the problem. Thanks for the tip about
|
By
Pat
·
#28172
·
|
|
Re: Skipped stitches
Have you tried the “Purple” tip needle? I’ve never sewed cork, so I’m not sure what needles are recommended for it, but my friend has sewed many on her 12000, 15000, and probably most on her
|
Have you tried the “Purple” tip needle? I’ve never sewed cork, so I’m not sure what needles are recommended for it, but my friend has sewed many on her 12000, 15000, and probably most on her
|
By
Cheryl Paul
·
#28171
·
|
|
Skipped stitches
I have been trying to make a phone bag using cork and a fabric lining. When I am sewing on cotton fabric, my Janome Horizon stitches beautifully but when I add layers of cork and fabric, the
|
I have been trying to make a phone bag using cork and a fabric lining. When I am sewing on cotton fabric, my Janome Horizon stitches beautifully but when I add layers of cork and fabric, the
|
By
ladybug35186
·
#28170
·
|
|
Re: Janome Compulock 888 Serger
Cynthia, I'm glad it helped! You may be replacing the needle again (on a new plate or your original one) if you have a tendency to bunch up your stitches on the stitch finger and then pull hard to
|
Cynthia, I'm glad it helped! You may be replacing the needle again (on a new plate or your original one) if you have a tendency to bunch up your stitches on the stitch finger and then pull hard to
|
By
Andrea LaVergne
·
#28169
·
|
|
Re: continual high pitched squeal on 15000 while embroidering
Pat is right. If it only happens while embroidering, remove the carriage. If still happens when sewing normally, then it's in the machine. That's about as far as you can go for diagnosis, and you'll
|
Pat is right. If it only happens while embroidering, remove the carriage. If still happens when sewing normally, then it's in the machine. That's about as far as you can go for diagnosis, and you'll
|
By
Jim Stutsman
·
#28168
·
|
