Date   

Re: reverse bobbin work

Anna C Simon <rbs11739@...>
 

I have not tried it yet. But what I would like to know is where did you get the designs. I am using a MC11000 machine.
 
TIA
 
 
 
 
 
Ann Simon
Our Etsy store

-------Original Message-------
 
From: st1b
Date: 2/14/2012 10:19:15 AM
Subject: [janome12000] reverse bobbin work
 
 

Has anyone tried reverse bobbin work (where the decorative thread is in the bobbin, the right side of the fabric is down in the hoop, you sew on the wrong side of the fabric) on the 12000?

I'm looking for suggestions on the tension. I tried just laying the bobbin thread on top of the bobbin, not using the either tension disc, and I was not pleased with the result. The decorative thread bunched up in some areas. I am using designs digitized for this type of stitching. While I do not want to mess with the tension screw in the bobbin case at all, has anyone changed the upper thread tension? Yes I can experiment on my own but perhaps one of you has the secret and I don't have to reinvent the wheel.

 


Re: 11000 thread holder

lmsoriginals1@sbcglobal.net <lmsoriginals1@...>
 

Could you post a picture. I am just not able to "see" this in my mind. Thanks!

Linda

--- In janome12000@yahoogroups.com, me2sew@... wrote:

I use a bendable straw to thread thru before going into the thread path
and it works. I cut the straw off an inch or so from the bendy part. Punch
small hole in other end and put thread thru that. Make a bend in the straw,
put on thread spindle, then thread machine as usual. I've done this for
several years. Grace


Re: 11000 thread holder

me2sew@...
 

I use a bendable straw to thread thru before going into the thread path and it works. I cut the straw off an inch or so from the bendy part. Punch small hole in other end and put thread thru that. Make a bend in the straw, put on thread spindle, then thread machine as usual. I've done this for several years. Grace


Re: reverse bobbin work

vicki chrobak
 

I haven't tried it yet. However, maybe the new FMQ bobbin holder might work when it comes out.

--
Vicki Jo

Has anyone tried reverse bobbin work (where the decorative thread is in the bobbin, the right side of the fabric is down in the hoop, you sew on the wrong side of the fabric) on the 12000?

I'm looking for suggestions on the tension. I tried just laying the bobbin thread on top of the bobbin, not using the either tension disc, and I was not pleased with the result. The decorative thread bunched up in some areas. I am using designs digitized for this type of stitching. While I do not want to mess with the tension screw in the bobbin case at all, has anyone changed the upper thread tension? Yes I can experiment on my own but perhaps one of you has the secret and I don't have to reinvent the wheel.


reverse bobbin work

Barb Stone
 

Has anyone tried reverse bobbin work (where the decorative thread is in the bobbin, the right side of the fabric is down in the hoop, you sew on the wrong side of the fabric) on the 12000?

I'm looking for suggestions on the tension. I tried just laying the bobbin thread on top of the bobbin, not using the either tension disc, and I was not pleased with the result. The decorative thread bunched up in some areas. I am using designs digitized for this type of stitching. While I do not want to mess with the tension screw in the bobbin case at all, has anyone changed the upper thread tension? Yes I can experiment on my own but perhaps one of you has the secret and I don't have to reinvent the wheel.


Re: My 12000

Judy <judyjanome@...>
 

Sorry to hear you are under the weather. I spent the greater part of the day at the hospital with my husband as I will tomorrow. I can't find to get to machine. I am sure Janome will make it right for you. Judyjanome

Sent from my iPhone


My 12000

Anne <csarina43@...>
 

My 12000 is on its way back to Janome. My dealer tried the machine on Saturday and it did exactly what I said it would do. I guess it will be a couple of days before I hear anything.

I am crook just now, have a throat infection so spent most of the day in bed.......


Re: MBX

Donna Morton
 

You can create the hoop but MBX will not automatically split the design.   Creating a 200 X 360 hoop and saving each part as a vp3 file would work better.  That way you could load them into you big hoop at the machine and line them up there.
 
Donna M
Canada
 

From: Grace
Sent: Sunday, February 12, 2012 7:18 PM
Subject: [janome12000] MBX
 
 

I know this is a silly question, but here goes. Is it possible to create a new hoop for a larger design (approx. 14x14) that would be used on a Pfaff machine. Or can you only create a new hoop for the Janome machines? Thanks.


Re: 11000 thread holder

lmsoriginals1@sbcglobal.net <lmsoriginals1@...>
 

I too am using my 11000 thread holder. However, I am having a problem with the thread jumping out of the first of the threading path. What are you using as a thread guide to lead the thread from the top of the thread holder to the beginning of the thread path?

Linda

--- In janome12000@yahoogroups.com, "thistlebug" <pegijane39@...> wrote:

Hi, I did use the screws that were in back of the 12000 to support my 11000 thread holder without any problems. Did not have to get a larger size screw. What was on there worked just fine. I just screwed them in a little more after I attached the stand to make it sturdy. It doesn't take much to make me happy. Also went to my first class on creating my own stitches and loved it. Plan to do more on my own. Every day something new and exciting. Peg in cold FL


Stupendous Stitching/cording discovery

vicki chrobak
 

Quite by accident i noticed that Satin stitches #1 & 2 are listed as cording stitches on our machine. FWIW.

--
Vicki Jo


Re: MBX

Bea Rosier <bearosier@...>
 

The only time I created a different hoop, I defined it's parameters and then named it and it worked just fine.  You should be able to do it too.  What you will discover is that when you are ready to save the stitch file, it will only save if you are using the suffix for the pfaff or whatever... In other words, it will not save as .jef if you have the user defined hoop designated..


On Feb 12, 2012, at 9:18 PM, "Grace" <me2sew@...> wrote:

 

I know this is a silly question, but here goes. Is it possible to create a new hoop for a larger design (approx. 14x14) that would be used on a Pfaff machine. Or can you only create a new hoop for the Janome machines? Thanks.


MBX

Grace <me2sew@...>
 

I know this is a silly question, but here goes. Is it possible to create a new hoop for a larger design (approx. 14x14) that would be used on a Pfaff machine. Or can you only create a new hoop for the Janome machines? Thanks.


Re: MBX and design gallery

gbmko
 

I never had Digitizer Pro, so this was a new install. Also, as I'm going through the wonderful instructional video by Trevor, and realized I didn't have those folders showing on the left side like on his screen, I discovered the "hide/show folders" button. DUH! What a difference that made. It's all so easy now!

I'm REALLY enjoying this software, even if my Corel is all messed up. I sent questions to both Janome and Corel about the issue, so I'll let you know what I find out.

--- In janome12000@yahoogroups.com, "Jim_Stutsman" <jim@...> wrote:

Apparently Design Gallery was installed with MBX, but you were still looking at where the Embroidery Gallery used to be. MBX moves it from Drive C to the My Documents folder (aka Documents Library in Windows 7).

--- In janome12000@yahoogroups.com, "gbmko" <gbmko@> wrote:

Woo hoo! I accidently figured this one out! I discovered where on my computer that the embroidery album had installed. Then opened design gallery, hit view, browse location, and then opened it from the folder on my computer...so now all the pictures open in design gallery. So, I think that is the solution if anyone else has this problem. Barbara Jean


Re: MBX and design gallery

Jim_Stutsman <jim@...>
 

Apparently Design Gallery was installed with MBX, but you were still looking at where the Embroidery Gallery used to be. MBX moves it from Drive C to the My Documents folder (aka Documents Library in Windows 7).

--- In janome12000@yahoogroups.com, "gbmko" <gbmko@...> wrote:

Woo hoo! I accidently figured this one out! I discovered where on my computer that the embroidery album had installed. Then opened design gallery, hit view, browse location, and then opened it from the folder on my computer...so now all the pictures open in design gallery. So, I think that is the solution if anyone else has this problem. Barbara Jean


Re: corel and MBX

Jim_Stutsman <jim@...>
 

If you installed MBX as an update "on top" of Digitizer Pro, and didn't check the Design Gallery box during installation, the shortcut on your desktop will be pointing to the old Design Gallery from Digitizer Pro. Run the MBX installer again and make sure the Design Gallery option is checked.

--- In janome12000@yahoogroups.com, "gbmko" <gbmko@...> wrote:

I guess the good news is that I never tried to uninstall corel essentials! I put the CD back in and did a "repair". Neither of the "corels" were working before I tried anything. that's when I tried putting the plug in into x5...at least it got rid of the message, and I thought I had "fixed" it, until I realized it still didn't work! I'll try doing a repair with my x5 CD, and if that doesn't work, will leave everything alone and contact janome.

This is the part of computer software stuff I don't like!

Any idea why nothing but black line boxes shows in designer gallery? Sorry for the headache emails! I sure appreciate your wisdom! Barbara Jean


MBX and design gallery

gbmko
 

Woo hoo! I accidently figured this one out! I discovered where on my computer that the embroidery album had installed. Then opened design gallery, hit view, browse location, and then opened it from the folder on my computer...so now all the pictures open in design gallery. So, I think that is the solution if anyone else has this problem. Barbara Jean


11000 thread holder

thistlebug <pegijane39@...>
 

Hi, I did use the screws that were in back of the 12000 to support my 11000 thread holder without any problems. Did not have to get a larger size screw. What was on there worked just fine. I just screwed them in a little more after I attached the stand to make it sturdy. It doesn't take much to make me happy. Also went to my first class on creating my own stitches and loved it. Plan to do more on my own. Every day something new and exciting. Peg in cold FL


Re: corel and MBX

gbmko
 

I guess the good news is that I never tried to uninstall corel essentials! I put the CD back in and did a "repair". Neither of the "corels" were working before I tried anything. that's when I tried putting the plug in into x5...at least it got rid of the message, and I thought I had "fixed" it, until I realized it still didn't work! I'll try doing a repair with my x5 CD, and if that doesn't work, will leave everything alone and contact janome.

This is the part of computer software stuff I don't like!

Any idea why nothing but black line boxes shows in designer gallery? Sorry for the headache emails! I sure appreciate your wisdom! Barbara Jean

--- In janome12000@yahoogroups.com, "Jim_Stutsman" <jim@...> wrote:

That warning message is one of the more misleading that I've ever seen. The Corel plugin that MBX uses is very different from the standard Corel 5, and even if they were compatible (they aren't), you cannot simply copy files from one to the other. As in all Windows programs, there are myriad entries in the Registry that have to be updated through an installation process. But it gets much, much worse.

Uninstalling the Corel from MBX is NOT recommended because it is incomplete and once attempted, will not allow a successful installation to occur. I suspect that the attempt to uninstall damaged the existing Corel installation, which is why it will not open now. Again we're back to registry entries, and it's likely that some of those entries where shared between the existing Corel 5 and the Essentials installed with MBX. The Windows Registry is like a house of cards made of tissue paper between a fire and a fan. It takes only the slightest breeze to collapse it into a pile of burnt rubble.

I'm not at all optimistic on the possibility of recovery. I have been told by MBX support folks that reinstallation of MBX is not possible after an attempted uninstall of Corel Essentials. My advice would be to try to install Corel 5 from your original CD, even though it did not fully uninstall. That would rebuild the Registry entries. Be sure to install the latest of any updates that may be available for Corel 5.

If Digitizer MBX will still open, use it that way without the Corel plugin. The alternative would be to reinstall Windows 7, or if your system came with a recover CD, to use that. Either option will remove EVERYTHING from your computer, so it's essential that you back up all of your data first. Before you take this very radical step, I would suggest that you contact Janome Tech Support for advice. This may take several days, because they don't have a very big support staff, and they are often overwhelmed. If there is a non-destructive way to recover from this, they may be able to guide you step by step. To increase the probability of success in this, you should not do anything more to try to fix it yourself.

--- In janome12000@yahoogroups.com, "gbmko" <gbmko@> wrote:

Dear Jim,I added a screen shot in files of the message I received when I tried to use the embroidery to graphics feature. I tried copying that plug in from essentials to graphics suite 5, and it did come up with the embroidery to graphics window...which never went away...and went to Corel...unuseable, and even when I went back to embroidery, the window was still sitting there.

I have windows 7, 64 bit. My corel graphics suite 5 will not even open now, and I tried uninstalling it, as I guessed the corel from MBX was interferring, but it wouldn't uninstall.

Also, when I open the design gallery, there is nothing there, like on the video by Trevor.

Any suggestions? Thanks so much! Barbara jean


Re: corel and MBX

Jim_Stutsman <jim@...>
 

That warning message is one of the more misleading that I've ever seen. The Corel plugin that MBX uses is very different from the standard Corel 5, and even if they were compatible (they aren't), you cannot simply copy files from one to the other. As in all Windows programs, there are myriad entries in the Registry that have to be updated through an installation process. But it gets much, much worse.

Uninstalling the Corel from MBX is NOT recommended because it is incomplete and once attempted, will not allow a successful installation to occur. I suspect that the attempt to uninstall damaged the existing Corel installation, which is why it will not open now. Again we're back to registry entries, and it's likely that some of those entries where shared between the existing Corel 5 and the Essentials installed with MBX. The Windows Registry is like a house of cards made of tissue paper between a fire and a fan. It takes only the slightest breeze to collapse it into a pile of burnt rubble.

I'm not at all optimistic on the possibility of recovery. I have been told by MBX support folks that reinstallation of MBX is not possible after an attempted uninstall of Corel Essentials. My advice would be to try to install Corel 5 from your original CD, even though it did not fully uninstall. That would rebuild the Registry entries. Be sure to install the latest of any updates that may be available for Corel 5.

If Digitizer MBX will still open, use it that way without the Corel plugin. The alternative would be to reinstall Windows 7, or if your system came with a recover CD, to use that. Either option will remove EVERYTHING from your computer, so it's essential that you back up all of your data first. Before you take this very radical step, I would suggest that you contact Janome Tech Support for advice. This may take several days, because they don't have a very big support staff, and they are often overwhelmed. If there is a non-destructive way to recover from this, they may be able to guide you step by step. To increase the probability of success in this, you should not do anything more to try to fix it yourself.

--- In janome12000@yahoogroups.com, "gbmko" <gbmko@...> wrote:

Dear Jim,I added a screen shot in files of the message I received when I tried to use the embroidery to graphics feature. I tried copying that plug in from essentials to graphics suite 5, and it did come up with the embroidery to graphics window...which never went away...and went to Corel...unuseable, and even when I went back to embroidery, the window was still sitting there.

I have windows 7, 64 bit. My corel graphics suite 5 will not even open now, and I tried uninstalling it, as I guessed the corel from MBX was interferring, but it wouldn't uninstall.

Also, when I open the design gallery, there is nothing there, like on the video by Trevor.

Any suggestions? Thanks so much! Barbara jean


Re: Stupendous Stitching projects

Pinguin
 

Hello Vickym
this article appeared in an older issue of QA, I sent you the link of the digital magazine (a legal feature of it) off list.
Gerda

Op 11-02-12 17:14, vicki chrobak schreef:

 

Thank you for the links Gerda. I look forward to getting my next issue
of QA now! I had a project on the back burner similar to this but in
black & white. Now I know what the technique is called;-)

--
Vicki Jo