Today, an OM was here because his Ody has a strange pulse on the output also in MOX with mic gain closed. All few seconds irregulary we measured a peak like in the picture. The signal is about 1/3 of

Hi people. Finally, I can introduce you to an amplifier as a complete design. I will draw a schematic and prepare a BOM in near future. http://ody-sdr.com/2018/09/03/hfpu-100-the-amplifier-for-odyssey

Hi I tried today the Zeus Software with Odyssey-2. It should be compatible, but I cat't start it I allways get "Device not found. Please check Ethernet connection. I also ask Yan Alexeenko and he gave

The display is garbled but it looks like Bootloader mode displays Bootloader 2.2. This is how it was returned from David after fixing a problem where it was bricked. Nmap scan report for 192.168.10.89

Hi, i have succesfully installed again bootloader but display indicate "FPGA ERROR" all LEDs remain fixed on. All power voltages are correct. I have replaced resistor array close to memory from 4K7 to

Hi David Maybe you have an idea. If I use pure signal I have this effect in the video. **Video deleted*** It switches between Feedback level and Correcting. In the video is also the spectrum of the si

Hello, people. I suggest paying attention to the SDR Spark program. Works with Odyssey and AOP firmware, has a minimum of settings, but the most necessary things are there. An important difference fro

David, what is the difference between the two files: ODYSSEY-2_BOM_SA_board.odt, and ODYSSEY-2_BOM_22012018.odt? Thanks, Steve KA6S

Hi all After several months of waiting (since January 2020!) I at last received the PICkit and USB blaster that are needed to re-flash my ODY-2, which I bricked last year. I ordered from Ali Express b

Hi David Are this OC Pins everywhere availlable on the Ody? I think the first 3 OU_0 to OU_2 are for the PA (LPF Switching) and OU3 is for any use. But for Transverter Operation (2m and 70cm) I need a

Hello, people. The original article is here, use the translator on the top of page: http://www.sdr-deluxe.com/publ/cifrovoj_radiotrakt_transivera_ddc_module_2/1-1-0-78 Shortly, I have designed very sm

We have here 6 Ody2 built. 2 works perfect, and 4 has an issue in TX. We did much trouble shooting but have no idea what causes this issue. The output power of this 4 odys is not adjustable by thetis.

Hi All, i have implemented the Odyssey II PCB V12, using componets, indicated in BOM, purchased at Digikey. Please refer to the attached picture. Following the Reto's document procedure i have success

Does anybody uses the Andromeda controller with Ody2 I will try it, but I'm not sure it works. But after some discussion with the author LA2NI it should work. So I let produce boards for the controlle

hi all The magic tee pcb have L1-L3 C1-C3 and 2+2:3 core and 1pcs diode , but i can't find the value and how to make the L1-L3 may I have some tips? yours bg2kkq

hi all I'm not sure the back of FPGA cap value so I use 0603 100nf cap.Is my capacitor installed correctly? Yours BG2KKQ

Hi, the memory W25Q64FW is obsolete and it is no more available at Digikey and Mouser. I have found on Ebay only W25Q64JVS. I would like to know if JVS version is compatible and there is a new memory

A firend soldered 3 PC's of Ody2. Becasue he has no programmers he broght them to me. All the programming was successful. Also the Firmware with the programmer (python) cluld be programmed into slot 1

Hello, I would like to share my project about Odyssey 2 hopping that can be useful to someone else. I wrote from scratch a new programmer, a new MCU firmware, and made changes to the Bootloader and to

HI all this smt of ODYSSEY II 1W SMA , it's 340R 2512 of bom? I'm not sure yours bg2kkq