The Kickstarter offering is now gone, if I understand well. I read the following, also, “In the future, I'll present also an amplifier(15W), VHF transverter and autotuner ih the similar housing and th

Disconnected power until this evening. Pressed power switch, reconnected power, hit power on and it's up. 73 ... Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdah

Hello, people. You didn't hear about me a long time, I am sorry. This time I made the first preorder for my russian-language customers. I have made 6 pcs of Odyssey-2 boards and some of them work in a

Hi people. I find a couple mistakes in Thetis 2.5.3. If you find something too - write here. 1) Alex Enable bit (General CC byte 59 bit 0) is always in 1, because of wich pins DATA, CLOCK, EN don't wo

David, I've had my top off recently - and started noticing the issues with power on/off others have mentioned. I wanted to make a suggestion as to what might be the issue - first what I noticed. I had

Thank you very much!! I was looking at Protocol2 - and indeed it looks like it SHOULD be bit 0! For each Alex that you add you should index the bit. I think the original use of this was likely to cont

David, Saw SPI once - not sure why I'm not seeing it more - In ANY case - I had to modify PiHPSDR code to see it. There are a couple of issues - First - here is the C Code in PiHPSDR if(filter_board==

1. I went looking for the SPI bus to see if it was working - I don't see a SPI clock when I believe PiHPSDR is telling it to change bands. Is the SPI port functional yet? 2. I compiled the Odyssey 1.1

I can connect to my ODY 1 using OpenHPSDR mRX v3.4.7, Thetis v2.5.3 and cuSDR64Beta v).3.3.0. With fixed IP. Using the same setup my Gigabit router DHCP assigns an IP to my ODY 2. I can see the asignm

Something I had yesterday. Power switch pressed nothing on the LCD. Removed front panel and saw 4 green LEDS lit solid. Put the cover back on and recycled power by removing the input plu and inserting

Gigabit connection to laptop. HPSDRBootloader --> Test for bootloader� gets no further than Reading MAC address. 73 ... Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus

LCD displays ODYSSEY and it's stuck on Read MAC address. Should bootloader mode be indicated on the LCD display? I tried powering up with my keyer sending alternate dot/dash and I also tried with a st

David, I don't believe being able to WRITE a MAC is required. I would think the MAC is assigned by the device manufacturer?? If NOT the case -then you as the manufacturer would be expected to supply a

David, Thanks! I will give it a try. Wound up spending the weekend working on packaging...so still have debug to do on my ptt circuit. It is identical to your suggestion but not switching.... thinking

This sounds like my issue to. I have tried on a switch as well as router and no luck with DHCP so far. Steve ka6s

David, I don't get much chance to look at this during the week. I am not seeing PTT either as far as I can tell. I don't know if I blew the FPGA or cockpit error on my part yet. Still have some starin

Hi. There is a schematic with relay commutation, you can assembly this on Prototyping PSB board https://www.ebay.com/itm/1pc-6x8cm-Double-Side-Protoboard-Circuit-Universal-DIY-Prototype-PCB-Board-G/13

Hi David My Odyssey-II has arrived and I collected it from the customs. I had to pay also 217 euro customs duty + VAT so this is more or less what would be expected in european countries. The package

So that seems to be the last thing I needed to do - the Synth/placement is continuing. I hope to be able to install this Saturday and try to see if I can get the IOs to wiggle. I wanted to be able to

In version 1.1 I found the .mif files down in the Polyphase directory. I moved them up a level and had to rename one as found below. The compile then continued. mv coefi8_1024.mif coefI8_1024.mif Stev