The display is garbled but it looks like Bootloader mode displays Bootloader 2.2. This is how it was returned from David after fixing a problem where it was bricked. Nmap scan report for 192.168.10.89

Today, an OM was here because his Ody has a strange pulse on the output also in MOX with mic gain closed. All few seconds irregulary we measured a peak like in the picture. The signal is about 1/3 of

Hi people. Finally, I can introduce you to an amplifier as a complete design. I will draw a schematic and prepare a BOM in near future. http://ody-sdr.com/2018/09/03/hfpu-100-the-amplifier-for-odyssey

Hi David Are this OC Pins everywhere availlable on the Ody? I think the first 3 OU_0 to OU_2 are for the PA (LPF Switching) and OU3 is for any use. But for Transverter Operation (2m and 70cm) I need a

Hello, people. The original article is here, use the translator on the top of page: http://www.sdr-deluxe.com/publ/cifrovoj_radiotrakt_transivera_ddc_module_2/1-1-0-78 Shortly, I have designed very sm

We have here 6 Ody2 built. 2 works perfect, and 4 has an issue in TX. We did much trouble shooting but have no idea what causes this issue. The output power of this 4 odys is not adjustable by thetis.

Hi All, i have implemented the Odyssey II PCB V12, using componets, indicated in BOM, purchased at Digikey. Please refer to the attached picture. Following the Reto's document procedure i have success

Does anybody uses the Andromeda controller with Ody2 I will try it, but I'm not sure it works. But after some discussion with the author LA2NI it should work. So I let produce boards for the controlle

hi all The magic tee pcb have L1-L3 C1-C3 and 2+2:3 core and 1pcs diode , but i can't find the value and how to make the L1-L3 may I have some tips? yours bg2kkq

hi all I'm not sure the back of FPGA cap value so I use 0603 100nf cap.Is my capacitor installed correctly? Yours BG2KKQ

Hi, the memory W25Q64FW is obsolete and it is no more available at Digikey and Mouser. I have found on Ebay only W25Q64JVS. I would like to know if JVS version is compatible and there is a new memory

A firend soldered 3 PC's of Ody2. Becasue he has no programmers he broght them to me. All the programming was successful. Also the Firmware with the programmer (python) cluld be programmed into slot 1

Hello, I would like to share my project about Odyssey 2 hopping that can be useful to someone else. I wrote from scratch a new programmer, a new MCU firmware, and made changes to the Bootloader and to

HI all this smt of ODYSSEY II 1W SMA , it's 340R 2512 of bom? I'm not sure yours bg2kkq

Hi All, i have purchased on Ebay the Odyssey II PCB and the infrared *reflow oven T962* ( http://www.tech168.cn/en/Item/Show.asp?m=2&d=584 ) I have seen on youtube the following interesting tutorial h

Hello David, I did some tests with the Andromeda Controller and Thetis. After a few minutes, sometins half an hour, the audio breaks on the Ody2 headpohne/speaker connector. The signal in Thetis is al

Hi all Today I tried out PIHPSDR. Installation on raspian os and rPI 4 model B worked fine. After start The Ody2 was recognized as Angelina Protocol 2. But after press on Start, the software runs with

I purchased a PC board for this project, and have all the components yet to be placed on the board. I've looked around for a schematic for this design, and found only a block diagram. It's going to be

A HAM friend has finished his ody-2 last week. It seems to work, I programmed it for him, because he has no porgrammes for mcu and fpga. All worked fine. After that the ody works with sdr-console (Fir

Hello David, Can I get the value of the ferrite beads on the pcb? Thanks! Peter, DG2NPE David Fainitski <rolin791@...> schrieb am Mo., 23. Nov. 2020, 15:50: Hi, Retro. 4 LEDs will explain you what is