Hello! I would like to inform Odyssey folk about possible modification which was made by Yuri EU2AV ;-) He modified Odyssey firmware and it is recognized as Anan7000 now. It was made to work together

If anyone has a no-longer-used Odyssey 2 they’re willing to release for a reasonable price, I would appreciate an email. Thanks, 73, Randy, K7RAN ( k7ran@... )

the new version ody2 100w pa was done use lager relay for LPF use 7PLOE LPF AND N7DDC 7*7 ATU all board based on n7ddc's hfpu-100 ,thanks for his great job de bg2kkq

Hi All I've just initiated my Odyssey-2 build, PCB ordered via eBay, fpga ordered and now going through my junk box to start collecting parts. I have never attempted to solder a BGA before, and intend

Hi all, i'm interested in buy this board https://www.ebay.co.uk/itm/334172684076?hash=item4dce3e7f2c:g:7MkAAOSwjb1hXh4J but it is the board only. Does anyone have a bom and component placement diagram

Does anybody uses the Andromeda controller with Ody2 I will try it, but I'm not sure it works. But after some discussion with the author LA2NI it should work. So I let produce boards for the controlle

Hello all, This may be a bit of a ramble - but I feel I need to give a bit of back story. I have one of the earlier odyssesys, and it has worked fine for a long time. Last week when I turned it on - i

Hi, I went to the website, and the "buy" module is disabled. Is this still available?

Hi, My Ody2 just died today. Impossible to turn on. My initial search for faults ended with the self-resettable fuse next to the power cord gets extremely hot upon inserting the power cord (and natura

Hi, i have succesfully installed again bootloader but display indicate " *FPGA ERROR* " all LEDs remain fixed on. All power voltages are correct. I have replaced resistor array close to memory from 4K

The Ethernet PHY KSZ9031RNXCC is not availlable at the Moment and it seems that is availlable in late 2022 again. So my Question: Is there a replacement part witch can be used 1:1 in the ody2? There a

According to the SW, I can programm in Transmit setting Tab "TX inhibit" How can I programm this option to the DB15 Connector. I would need this so I can use a sequencer. Help is very much appreciated

Hi All, i have successfully tested my Odyssey II wih SDR Console V3 , using new protocol, , PowerSDR using old protocol and Thetis, using old protocol. With new protocol i have configured Thetis, last

HI David It is possible to modify 7*7 ATU hardware and software for odyssey pa unit includ TUNE and PTOTECT singal? Original HFPU-100 5*5 ATU was poor performance，and all unit only output only 50w. so

The display is garbled but it looks like Bootloader mode displays Bootloader 2.2. This is how it was returned from David after fixing a problem where it was bricked. Nmap scan report for 192.168.10.89

Today, an OM was here because his Ody has a strange pulse on the output also in MOX with mic gain closed. All few seconds irregulary we measured a peak like in the picture. The signal is about 1/3 of

Hi people. Finally, I can introduce you to an amplifier as a complete design. I will draw a schematic and prepare a BOM in near future. http://ody-sdr.com/2018/09/03/hfpu-100-the-amplifier-for-odyssey

Hi I tried today the Zeus Software with Odyssey-2. It should be compatible, but I cat't start it I allways get "Device not found. Please check Ethernet connection. I also ask Yan Alexeenko and he gave

Hi David Maybe you have an idea. If I use pure signal I have this effect in the video. **Video deleted*** It switches between Feedback level and Correcting. In the video is also the spectrum of the si

Hello, people. I suggest paying attention to the SDR Spark program. Works with Odyssey and AOP firmware, has a minimum of settings, but the most necessary things are there. An important difference fro