Hi David With other receiver I have to test it. In spectrum I don't found it, maybe I don't find the frequency or the sweep is too slow. I can see Realtime signals online in a span of 250kHz. Maybe Hb

Hi Sid Seems I didn't read this file. But bl 2.1 is the correct one. Because I use windows (I know you not) I use the new programmer for windows, works well. Before I had troubles with the python file

Hi Sid Use bootloader 2.1 from the GITHUB. https://github.com/Dfinitski/Odyssey-2_2017_TRX/blob/master/Odyssey_BL_2.1.zip And use the new mcu file David attached here. https://groups.io/g/ody-sdr/mess

Today, an OM was here because his Ody has a strange pulse on the output also in MOX with mic gain closed. All few seconds irregulary we measured a peak like in the picture. The signal is about 1/3 of

Hi David, It works!! Thanks for fixing it. vy 73 Reto

Today I did some experiments. And it seems, that I have to restart thetis after configuration of the transverter settings. After restart also the frequency of the transverter will be shown in the vfo

Hi David Thanks for the explanation. This seems a complicated experiment. I think we will try that in the group. For the moment I understand that our current PA is capable for 50W. So we can't make a

Hi David, Transformer is 1:3 And the 100 Ohms I mean for lienarity of Thetis Power Slider not feedback. https://groups.io/g/ody-sdr/message/1226 I use 270 Ohms at the moment for feedback an 100mA Ody2

@BG6RDF HI Weiwei I yesterday tested my Ody for output and also IM3. All values now are fine. I set PA gain to 38.8dB and make the measure. Conditions are Feedback resistor 270 Ohms, Bias 100mA and th

Oh.. I found it under Setup/F/W Set ! And it works as I expected. vy 73 Reto

Hi David, Thanks for your report. The Size is really nice. BUt your right, I have in the meantime too much devices. Also A KX3 which I sometimes use for SOTA. But also the Sparrow is useable for Sota.

Hi David, Dither Option: I search since yesterday for that opton, but it could also be an easy solutiuon ;) Is the dither option the following: I activate the Pins 4, 5 and 6 in the picture I send in

HI David, Thanks! Could be that I have different versions in the Slots. But slot on is reserved for the "productive" version. Slot 2 and 3 for experimental things and protocol 1 file. I think, i synch

Here a picture

Hi David Are this OC Pins everywhere availlable on the Ody? I think the first 3 OU_0 to OU_2 are for the PA (LPF Switching) and OU3 is for any use. But for Transverter Operation (2m and 70cm) I need a

The ic-705 seems to be a very interesting device. I also interested of your experience with this small device. Vy 73 Reto

Hi David, I tested it today, and it works. Now I have a good linear behavior of the Thetis slider from 1 to 100. ) With my actual Setup I have 3mW at 1 and 340mW at 100. Perfect! (270 Ohm Feedback and

Hi David, Ok, I also think that all new BGA's have solderballs preapplied. So, I also don't understand what Artur makes there ;) Artur has a new SParrow UI I think Where a DDC Module can be placed or

Hello David I read a bit in the i40 forum about the ddc2 board and i40 project. I also see that Artur made a new ui for his Sparrow and also a ddc2 design which fits to this board. Does your ddc2 boar

Hi David Thanks, I'll test this out and report here. Vy 73 Reto