Thanks Neoklis, Looks great, I'll do that mod. 73 ... Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Senior

Hi Sid, also no problems here with the MH31. Good modulation and normal power output at the 1W PA from Ody-2. vy 73 Reto

Hello, Sid. My MH-31 mic was tested with PowerSDR Wich has "mic 20db preamp" settings and also program mic amplification settings. No any problems. Dynamic microphones like MH-31 required 20db preamp

No, but I found this article that may confirm your problems. https://www.iarc.org/~4x1mk/modifying_the_MH-31_Yaesu_microphone.html -- Best Regards Neoklis - Ham Radio

Has anyone experienced low microphone level from the MH-31? With the ODY-2's 1W I get no movement with the SWR meter set to 5W PEP full scale. My setup ODYSSEY-2 --> 100W PA ex-IC737. At first I

Hi David, Thanks for the Input. I'll check this. I solder the transformers by iron and with some flux. But it could be that the solderwork is not perfect. DO you think that the currend of arround

Hello, Reto. For test the amp, touch each the input ports with a screwdriver, the signal streight should be identical. The SMD transformers can not to be soldered with hot air. If some drop of flux

Hi David, I built the AML-30 Antenna, without success at the Moment. I think there's something wrong and I have to check it. What is the current, de AMP consumes if the antenna is powered on? I

Hello David Thanks for the link. I'll look there and reading also in future. A question, is the firmware in master mode available? I think in the GITHUB is only the firmware in slave mode. Uhsdr:

Hello, Reto I have started a conversation about DDC Module 2 here on this group. I will update all the info about Sparrow 4 DDC overhere

Hello, Steve First of all you have to update the bootloader to actual version. Program MCU programmer with MCU.hex file from ANP firmware folder "Odyssey_ANP_2.1.2.zip" using PICkit 3

Hi Steve, If found some time I simulate your problem on my ody. Because I have all programmers, I finde a way out if it fails ;) vy 73 Reto

Reto, Thanks very much for the suggestions - I hope Dave will be able to chime in and deliver a few words of wisdom. Thanks for doing the instructions too. 73 Steve

Maybe not, I think it's possible to load only the firmware with the python script corresponding to your bootloader version. I think it's also possible to upgrade the bootloader to the newest if you

The question really is do I need to do those upgrades to update a working board to the latest version or do the old tools still work? Note...my board is working as built by David.

Hi Steve, 1. For programming the MCU you need a pickit 3 programmer 2. For programming the bootloader (.pof) you need a USB Blaster or Bit Blaster 3. For programming the Firmware you need a network

David, I've tried looking at email traffic for clear instructions - and I recall doing this with the Iambic keys being shorted (still have that fixture). What I don't recall was which program to use

Hi David, No more tests needed, it works now. I made a mistake with the Antenna connections. Very impressive the diversity function with two ADC! I tested in thetis. vy 73 Reto

Hello David Thanks for the links. Very impressive and diversity seems to work fine. I tried this yesterday, and if I press enable, rx1 stops working. Spectrum freezing and waterfall shows the last

I 've found https://www.youtube.com/watch?v=w7DFKCzNjlM https://www.youtube.com/watch?v=GLPzjPjHfsE https://www.youtube.com/watch?v=2ichrLZN7JI https://www.youtube.com/watch?v=7fXVgxM3J_0