I am sorry guys, I forgot that for correct bootloader's version indication you must to programm MCU with new hex files. Sid, you can write to 0 slot only bootloader.rbf and to slots 1-3 only

Hi David, Writing the .rbf file to slot 0 with BootLoader_2.0.pyw results in having to use quartus to restore with the .pof file. After that I use BootLoader_2.0.pyw which says the .rbf file should

Using BootLoader_2.0.pyw and selecting slot 0 only the rbf file is presented. Is that correct or should it be the .pof file? Not clear as to what slot the .pof file goes and where .rbf goes. 73 ...

David, I programmed the BL 2.1 too: 1st - by the BL2.1.pyw to slot 0. 1st time it succceeded, but when started - it displayed Bootloader 2.0. Then I tried again - this time it failed. Then I used

"bootloader 2 3" on the display ??? It should be " bootloader 2.1" Next step try to use old 2.0 Bootloader.pyw People are say that new one does not work reliability. Will see. It works with mine.

Active Serial Programming worked and Bootloader displayed on LCD. Bootloader 2 3 192.168.10.89         Slot 1 What next?    In Bootloader mode - BootLoader_2.1.pyw to load Bootloader.rbf

Because you are using JTAG mode. Use serial programming. JTAG mode uses for access to FPGA memory directly. Our goal - to flash dedicated EEPROM memory.

I get this error with or without bootloader mode when I try Add File. I am using altera 15.0. Intel 18.1 has a problem which I have raised with Intel - libpng12 is what it's looking for but all recent

Thanks David. I'll do that. 73 ... Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Senior Staff Specialist,

Hello, Sid It looks like the bootloader was accidently spoiled. You have to write bootloader.pof manually with byte blaster and Quartus. If something went wrong you need to keep the power of the

I selected slot 0 and used Odyssey_BL_2.1/Bootloader.rbf As it complained of a timeout it either didn't erase slot 0 or it partially erased slot 0 and timed out. 73 ... Sid. -- Sid Boyce ...

I do not have a direct connection, it is connected to a 16-port Gigabit switch. It finds the device but times out during erase. Increased one timeout value to 4 seconds, powered off and it won't power

Thanks David, AOK. 73 ... Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Senior Staff Specialist, Cricket

Hello, Sid. Yes, it is correct. But before change the bootloader by the same method with using bootloader 2.1 .rbf from this topic, flash to zero's slot. New firmware flash to needed slot 1 to

Hi David, Checking the procedure for upgrading is correct. 1. Power up in Bootloader mode. 2. ./BootLoader_2.1.pyw    (Address of my ODY-2 changed to 192.168.10.89) 3. select Odyssey_2_1.20_ANP.pof

Hello, people Small update our bootloader to 2.1 ver. Improved stability, "FPGA ERROR" message on the display when FPGA did not started, possibility to make a reset device after change a firmware by

Sorry, rbf file is here

Hello, people. There is new firmware based on the latest 12.0 firmware for Angelia (K5SO is autor). It should to work fine with new version of Thetis 2.6.7 Link for downloading Thetis -

Thank you David. That was not obvious😊 That’s clear now. I used to protect my receivers with such a trick when I was SWL… many years from now >The bulbs located close to RF connectors

Hello, Mark These two bulbs work here like fuses. If 100W from transmitter would go to RF input, the bulb will burned. Or, if power level will be around 20-50W, the bulb will to glow. You can short