Date   
Re: Ody II ANP 1.11 IP /Thetis configuration

AA6I Stan
 

I just looked at mine as I also use Thetis. Mine is uses Anan 10E . I did a lot of fiddling to get mine going but as I recall I used a static address also on the PC adapter. You also need to be running at Gigabit speeds as I understand ODY II does not do 100Mbps .


AA6I

On 2/19/2019 2:43 PM, Jan Verduyn wrote:

I am attempting to configure a new Ody II for a friend on a Windows 7 PC.  Despite many hours of trying this has not been successful. 
This Ody II  has ANP 1.11 installed in slot 1 and when switching on it shows it's IP address is 192.168.2.160  
The PC runs windows 7 OS. Software is Thetis v2.6.0.   

A direct Ethernet cable connection between PC and Ody II is used.  The Ethernet adapter is configured for 100 Mbps  and link enabled.   LAN status shows that packets are being sent but no packets are being returned.
Thetis setup screen is configured  "Enabled Static IP Address"  "Anan-100D"  with IP address 192.168.2.160 entered.

When starting up Thetis  an error is shown  "Unhandled exception has occurred in your application"
A socket operation was attempted to an unreachable network.  
Changing Thetis configuration to "Use last IP address" and restarting Thetis shows

Pinging Ody's IP address gives response "unreachable network".
Can somebody please provide a screenshot what the correct configuration is for Thetis on Windows 7 for  ANP1.11.

 Many thanks  Jan

Ody II ANP 1.11 IP /Thetis configuration

Jan Verduyn
 

I am attempting to configure a new Ody II for a friend on a Windows 7 PC.  Despite many hours of trying this has not been successful. 
This Ody II  has ANP 1.11 installed in slot 1 and when switching on it shows it's IP address is 192.168.2.160  
The PC runs windows 7 OS. Software is Thetis v2.6.0.   

A direct Ethernet cable connection between PC and Ody II is used.  The Ethernet adapter is configured for 100 Mbps  and link enabled.   LAN status shows that packets are being sent but no packets are being returned.
Thetis setup screen is configured  "Enabled Static IP Address"  "Anan-100D"  with IP address 192.168.2.160 entered.

When starting up Thetis  an error is shown  "Unhandled exception has occurred in your application"
A socket operation was attempted to an unreachable network.  
Changing Thetis configuration to "Use last IP address" and restarting Thetis shows

Pinging Ody's IP address gives response "unreachable network".
Can somebody please provide a screenshot what the correct configuration is for Thetis on Windows 7 for  ANP1.11.

 Many thanks  Jan

Re: Odyssey-2 in Linux, some progress

Neoklis Kyriazis
 

Hello, Neoklis
Hello David

According to openHPSDR protocol, programs will search Odyssey with
non-direction broadcast packets and this will not to work trough Wi-Fi
and non-Wi-Fi routers.
Well, actually for me it worked the other way round: I have the Ody as it
was shipped, with the AOP 1.10 firmware and I could not get it to work with
a direct connection to my PC. Of course it could have been my mistakes to
blame. But when I connected the Ody to my ISP's router, I was able to access
Ody with the HPSDRProgrammer_v2_nopcap and gave Ody the default static
IP of 192.168.2.160. I could also access Ody with both ghpsdr and linhpsdr, via
the router and through the WIFI connection of my PC to the router.

Now with the static IP I was able to access Ody with the ping command, after
I followed your instructions: I gave the PC's Ethernet port a static IP of
192.168.2.100/24 and 100Mb/Full Duplex setting. ping 192.168.2.160 now
works well but the other apps don't discover Ody. I think ping works because
I specify the IP address but other apps have to do discovery and this is where
I have the problem, I don't know what else I have to do to make discovery
work over the direct Ethernet connection.

Anyhow, I have learned a few things about LANs at least!

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 in Linux, some progress

David Fainitski
 

Hello, Neoklis

According to openHPSDR protocol, programs will search Odyssey with non-direction broadcast packets and this will not to work trough Wi-Fi and non-Wi-Fi routers.

For approach the result you should connect your Odyssey directly to your PC.

At least for the first time.

David 

Re: Odyssey-2 in Linux, some progress

Sid Boyce
 

Glad you have it running.
I use mine with linhpsdr on x86_64 openSUSE at 1536K samplerate with ANP firmware. I used pihpsdr on aarch64 nanoPi Fire3 as linhpsdr crashed.
If and when quisk supports Gigabit Ethernet, it would be my preferred application for Hermes, Hermes-Lite2 and ODY-2.
73 ... Sid.

On 17/02/2019 07:20, Neoklis Kyriazis via Groups.Io wrote:
Hi all,

Looks like my home work has paid off some, but not all! ;-)

With the help from this group and my distro's forum, I was able to connect
with Ody-2 and to give it a static IP of 192.168.2.160/24, the default. I
got this far by connecting Ody into my ISP's router and accessing it via my
WIFI connection. I used HPSRProgrammer_v2_nopcap to discover Ody and to give
it its default static IP address, which is now permanently stored in it.

I was also able to comm with it using both ghpsdr and linhpsdr apps which
discovered it OK but I didn't try to work Ody because ghpsdr crashes with
a segfault, apparently due to some bug in the GUI, and the streaming rate
apparently not high enough via my WIFI.

Anyhow, the important thing is that I got somewhere! :-)

I then tried a direct connection to my computer's Ethernet port. After some
experimentation with settings, I can ping Ody OK and it is also listed by:

# nmap -sT 192.168.2.100/24
Starting Nmap 7.70 ( https://nmap.org ) at 2019-02-17 09:09 EET
Nmap scan report for 192.168.2.160 (192.168.2.160)
Host is up (0.00013s latency).
All 1000 scanned ports on 192.168.2.160 (192.168.2.160) are filtered
MAC Address: 00:1E:C0:A5:F4:7E (Microchip Technology)

Nmap scan report for 192.168.2.100 (192.168.2.100)
Host is up (0.00035s latency).
Not shown: 999 closed ports
PORT   STATE SERVICE
22/tcp open  ssh

Nmap done: 256 IP addresses (2 hosts up) scanned in 31.27 seconds

Also by:
# ping 192.168.2.160
PING 192.168.2.160 (192.168.2.160) 56(84) bytes of data.
64 bytes from 192.168.2.160: icmp_seq=1 ttl=128 time=0.101 ms
64 bytes from 192.168.2.160: icmp_seq=2 ttl=128 time=0.190 ms
64 bytes from 192.168.2.160: icmp_seq=3 ttl=128 time=0.194 ms
64 bytes from 192.168.2.160: icmp_seq=4 ttl=128 time=0.165 ms
64 bytes from 192.168.2.160: icmp_seq=5 ttl=128 time=0.166 ms
64 bytes from 192.168.2.160: icmp_seq=6 ttl=128 time=0.192 ms
^C
--- 192.168.2.160 ping statistics ---
6 packets transmitted, 6 received, 0% packet loss, time 143ms
rtt min/avg/max/mdev = 0.101/0.168/0.194/0.032 ms

However, alas, all above apps (HPSRProgrammer, ghpsdr, linhpsdr) will not
discover Ody so again I am stuck.

So, any new hints/advise will be much appreciated, I just can't give up on
this!
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Odyssey-2 in Linux, some progress

Neoklis Kyriazis
 

Hi all,

Looks like my home work has paid off some, but not all! ;-)

With the help from this group and my distro's forum, I was able to connect
with Ody-2 and to give it a static IP of 192.168.2.160/24, the default. I
got this far by connecting Ody into my ISP's router and accessing it via my
WIFI connection. I used HPSRProgrammer_v2_nopcap to discover Ody and to give
it its default static IP address, which is now permanently stored in it.

I was also able to comm with it using both ghpsdr and linhpsdr apps which
discovered it OK but I didn't try to work Ody because ghpsdr crashes with
a segfault, apparently due to some bug in the GUI, and the streaming rate
apparently not high enough via my WIFI.

Anyhow, the important thing is that I got somewhere! :-)

I then tried a direct connection to my computer's Ethernet port. After some
experimentation with settings, I can ping Ody OK and it is also listed by:

# nmap -sT 192.168.2.100/24
Starting Nmap 7.70 ( https://nmap.org ) at 2019-02-17 09:09 EET
Nmap scan report for 192.168.2.160 (192.168.2.160)
Host is up (0.00013s latency).
All 1000 scanned ports on 192.168.2.160 (192.168.2.160) are filtered
MAC Address: 00:1E:C0:A5:F4:7E (Microchip Technology)

Nmap scan report for 192.168.2.100 (192.168.2.100)
Host is up (0.00035s latency).
Not shown: 999 closed ports
PORT   STATE SERVICE
22/tcp open  ssh

Nmap done: 256 IP addresses (2 hosts up) scanned in 31.27 seconds

Also by:
# ping 192.168.2.160
PING 192.168.2.160 (192.168.2.160) 56(84) bytes of data.
64 bytes from 192.168.2.160: icmp_seq=1 ttl=128 time=0.101 ms
64 bytes from 192.168.2.160: icmp_seq=2 ttl=128 time=0.190 ms
64 bytes from 192.168.2.160: icmp_seq=3 ttl=128 time=0.194 ms
64 bytes from 192.168.2.160: icmp_seq=4 ttl=128 time=0.165 ms
64 bytes from 192.168.2.160: icmp_seq=5 ttl=128 time=0.166 ms
64 bytes from 192.168.2.160: icmp_seq=6 ttl=128 time=0.192 ms
^C
--- 192.168.2.160 ping statistics ---
6 packets transmitted, 6 received, 0% packet loss, time 143ms
rtt min/avg/max/mdev = 0.101/0.168/0.194/0.032 ms

However, alas, all above apps (HPSRProgrammer, ghpsdr, linhpsdr) will not
discover Ody so again I am stuck.

So, any new hints/advise will be much appreciated, I just can't give up on
this!

Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

The default IP of Odyssey is 192.168.2.160
Thanks David. I will be trying again later once I am better prepared about
networking and finishing seasonal chores, and nursing my dog. Had an
operation to clear that large abscess on its cheek.

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

David Fainitski
 

The default IP of Odyssey is 192.168.2.160

Re: Odyssey-2 on Linux

Sid Boyce
 

OK. After using ethtool, check
ifconfig -a
ifconfig <interface> 192.168.100.1 up
ping 192.168.100.1   --- should show pings working.

ifconfig -- which should display something like this.
enp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.10.238  netmask 255.255.255.0  broadcast 192.168.10.255
        inet6 fe80::490f:3a27:6ac1:7f00  prefixlen 64  scopeid 0x20<link>
        ether 1c:6f:65:9f:5c:9e  txqueuelen 1000  (Ethernet)
        RX packets 32439609  bytes 41896916150 (41.8 GB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 14351411  bytes 9296515806 (9.2 GB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
73 ... Sid.

On 10/02/2019 07:11, Neoklis Kyriazis via Groups.Io wrote:
# ethtool -s <port> speed 100 duplex full autoneg off
73 ... Sid.
Thanks Sid, but still it didn't work. I think one problem is that I never had to do
much work on networking, save setting up WiFi, so I can't see what is wrong or
what I am doing wrong. And even if I could, I can't find the solution myself. So
giving up for now, I have a lot of chores waiting for me, so next time I have
spare time I will teach myself some networking and try again.

My thanks to all that chipped in help.

73's

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

# ethtool -s <port> speed 100 duplex full autoneg off
73 ... Sid.
Thanks Sid, but still it didn't work. I think one problem is that I never had to do
much work on networking, save setting up WiFi, so I can't see what is wrong or
what I am doing wrong. And even if I could, I can't find the solution myself. So
giving up for now, I have a lot of chores waiting for me, so next time I have
spare time I will teach myself some networking and try again.

My thanks to all that chipped in help.

73's

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

Sid Boyce
 

In Linux

# ethtool -s <port> speed 100 duplex full autoneg off
73 ... Sid.

On 09/02/2019 20:20, David Fainitski wrote:
Hello, Neoklis

For now you should set up your PC Ethernet connection to Static IP with 192.168.2.100 address and 255.255.255.0 subnet mask.

Also you should set the 100M Full Duplex  mode on your network card ( I don;t know how to in Linux).

After that your Odyssey will be visible for SDR programs with 192.168.2.160 IP (Static IP)

Read this document https://apache-labs.com/downloadsfiles/1003_ANAN-100-Users-Guide.pdf

If you have changed firmware to ANP version, this manual will be helpful
https://apache-labs.com/download_file.php?downloads_id=1010

David
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks

Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

Thanks David! I will try that tomorrow and see what happens. For now
I am watching over my little dog - she got a sting from something and
she has a huge bulge on her cheek. Luckily  my vet agreed to an
emergency call and she is getting better! :-)

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

David Fainitski
 

Hello, Neoklis

For now you should set up your PC Ethernet connection to Static IP with 192.168.2.100 address and 255.255.255.0 subnet mask.

Also you should set the 100M Full Duplex  mode on your network card ( I don;t know how to in Linux).

After that your Odyssey will be visible for SDR programs with 192.168.2.160 IP (Static IP)

Read this document https://apache-labs.com/downloadsfiles/1003_ANAN-100-Users-Guide.pdf

If you have changed firmware to ANP version, this manual will be helpful
https://apache-labs.com/download_file.php?downloads_id=1010

David 

Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

Isaac

I already tried the boot loader under different settings etc but no joy.
There must be some fundamental problem that I don't understand
because of limited knowledge of networking.

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

Isaac
 

Sorry, I forgot to mention that the Bootloader_2.0 is written in Pyton,
which of course runs on Linux as well as Windows.

Isaac

-----Original Message-----
From: ody-sdr@groups.io <ody-sdr@groups.io> On Behalf Of Sid Boyce
Sent: Saturday, 9 February 2019 0:15
To: ody-sdr@groups.io
Subject: Re: [ody-sdr] Odyssey-2 on Linux

Another thing to try, instal isc-dhcp-server so you can get an IP address
for the PC and hopefully the ODY-2 when you reboot.
https://help.ubuntu.com/lts/serverguide/dhcp.html.en

Wow! Back then we had lots of rain during the Winter only but nothing that
disruptive.
OK, you are North of Erimi village.
73 ... Sid.


On 08/02/2019 17:29, Neoklis Kyriazis via Groups.Io wrote:
That's weird as the first time I set mine up it was laptop Gigabit
port --> ODY-2.
Hmm, in that case I will have to try some more. I used my desktop
(only a Compulab fitPC4) but with dhcpcd disabled. I will try my
laptop too, in case there is some hardware issue.

I remember the winter downpours there back in the 1966 - 1969,
Yes, in those days it was more rainy. In fact many people feel that
this winter reminds them of that era, we had (have!) a really rainy
weather. But frequent thunderstorms force me to cut off electricity
and unplug everything. Lost some gear including my old computer,
Yaesu power supply, laser printer, roof fans, garage door motor etc
after a direct hit on power cables. And one pine tree in my garden!
( I live in Souni, a few km north of Episkopi).

73's

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/



Re: Odyssey-2 on Linux

Isaac
 

Guys, why don't you use David's Bootloader 2.0
(https://github.com/Dfinitski/Odyssey-2_2017_TRX/blob/master/BootLoader_2.0.
pyw.zip) ? It will find Odyssey-2 and it's IP for you (if it's on the same
network).
It also allows you to set the IP you wish (static IP). And BTW it allows you
to program the Ody bootloader and 2 firmware versions (e.g.
Odyssey_2__1.11_ANP for new (1Gbs) protocol and Odyssey_2__1.11_AOP_100 for
the old one (100Mbs).

73 Isaac 4Z1AO

-----Original Message-----
From: ody-sdr@groups.io <ody-sdr@groups.io> On Behalf Of Sid Boyce
Sent: Saturday, 9 February 2019 0:15
To: ody-sdr@groups.io
Subject: Re: [ody-sdr] Odyssey-2 on Linux

Another thing to try, instal isc-dhcp-server so you can get an IP address
for the PC and hopefully the ODY-2 when you reboot.
https://help.ubuntu.com/lts/serverguide/dhcp.html.en

Wow! Back then we had lots of rain during the Winter only but nothing that
disruptive.
OK, you are North of Erimi village.
73 ... Sid.


On 08/02/2019 17:29, Neoklis Kyriazis via Groups.Io wrote:
That's weird as the first time I set mine up it was laptop Gigabit
port --> ODY-2.
Hmm, in that case I will have to try some more. I used my desktop
(only a Compulab fitPC4) but with dhcpcd disabled. I will try my
laptop too, in case there is some hardware issue.

I remember the winter downpours there back in the 1966 - 1969,
Yes, in those days it was more rainy. In fact many people feel that
this winter reminds them of that era, we had (have!) a really rainy
weather. But frequent thunderstorms force me to cut off electricity
and unplug everything. Lost some gear including my old computer,
Yaesu power supply, laser printer, roof fans, garage door motor etc
after a direct hit on power cables. And one pine tree in my garden!
( I live in Souni, a few km north of Episkopi).

73's

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/



Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

Hello, Neoklis.
Hello David

It would be good idea to change the Bootloader to new Bootloader 2.0. This >allows you to flexibly manage parameters with the simple Pyton's program
OK, this is something I should do eventually, but what I am trying to do now
is to communicate with the Ody-2 over the Ethernet connection, using linhpsdr or ghpsdr or some compatible software (I have both compiled OK but they don't communicate with Ody).

What I like to know is, can this be done with a direct connection to my computer, with no Ethernet switch, and with the Ody-2 in its original state
that it was when I bought it? So far any attempts have failed.

Thanks for joining in the discussion!

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

David Fainitski
 

Hello, Neoklis.

It would be good idea to change the Bootloader to new Bootloader 2.0. This allows you to flexibly manage parameters with the simple Pyton's program under Linux.

Also you will to have the possibility write 2 different firmwares (up to 3) and change them fast after restart Ody.

You will need ALTERA USB Blaster for downloading Bootloader 2.0 firmware.

Read here about this  http://ody-sdr.com/2018/05/06/the-bootloader-2-0-for-odyssey-2/

Also you will need to use Pickit 3 from Microchip for flashing PIC processor with new firmware.

David

Re: Odyssey-2 on Linux

Neoklis Kyriazis
 

Another thing to try, instal isc-dhcp-server so you can get an IP
address for the PC and hopefully the ODY-2 when you reboot.
https://help.ubuntu.com/lts/serverguide/dhcp.html.en
OK, I will try that too. This may also be relevant although its for
Windoze and ANAN rigs:
http://www.w1aex.com/anan/anan.html#network

OK, you are North of Erimi village.
Wow!, you know my geography better than me...;-)

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/

Re: Odyssey-2 on Linux

Sid Boyce
 

Another thing to try, instal isc-dhcp-server so you can get an IP address for the PC and hopefully the ODY-2 when you reboot.
https://help.ubuntu.com/lts/serverguide/dhcp.html.en

Wow! Back then we had lots of rain during the Winter only but nothing that disruptive.
OK, you are North of Erimi village.
73 ... Sid.

On 08/02/2019 17:29, Neoklis Kyriazis via Groups.Io wrote:
That's weird as the first time I set mine up it was laptop Gigabit
port --> ODY-2.
Hmm, in that case I will have to try some more. I used my desktop
(only a Compulab fitPC4) but with dhcpcd disabled. I will try my
laptop too, in case there is some hardware issue.

I remember the winter downpours there back in the 1966 - 1969,
Yes, in those days it was more rainy. In fact many people feel that
this winter reminds them of that era, we had (have!) a really rainy
weather. But frequent thunderstorms force me to cut off electricity
and unplug everything. Lost some gear including my old computer,
Yaesu power supply, laser printer, roof fans, garage door motor etc
after a direct hit on power cables. And one pine tree in my garden!
( I live in Souni, a few km north of Episkopi).

73's

--
Best Regards
Neoklis - Ham Radio Call:5B4AZ
http://www.5b4az.org/