Hi, I'm testing tlf during OM/OK contest. And I noticed that when I'm in S&P mode and when I press Enter to confirm qso, IT always sent <my call> and the message defined in contest rules as S&P_TU_MSG

http://www.w1hkj.com/alpha/flrig/ flrig-1.4.7.45.tar.gz 2022-11-12 11:44 1.0M flrig-1.4.7.45_BS.dmg 2022-11-12 11:44 3.9M flrig-1.4.7.45_HS.dmg 2022-11-12 11:44 2.3M flrig-1.4.7.45_LI.dmg 2022-11-12 1

at http://www.w1hkj.com/alpha/flrig/ flrig-1.4.7.43.tar.gz 2022-11-11 14:24 1.0M flrig-1.4.7.43_BS.dmg 2022-11-11 14:24 3.9M flrig-1.4.7.43_HS.dmg 2022-11-11 14:24 2.3M flrig-1.4.7.43_LI.dmg 2022-11-1

Hi friends, fellow hams, and HamPi / HamPC users! I am pleased to announce that HamPi 3.1.1b2, the comprehensive award-winning ham radio software distribution for the Raspberry Pi Inovato Quadra SBC i

I have set up the following macro to (what I think) is QSY to 7.095 MHz at 2300: <SKED:2300><QSY:7095><RIGMODE:PKTUSB> While I *think* it does all that, it also starts transmitting ("Macro 'ARRL Sked'

Hi all, I thought it would be beneficial to have a groups.io for Inovato Quadra owners using them for ham radio, so I created this group: https://groups.io/g/Inovato-Quadra-4-HamRadio Please consider

I just received a DVMEGA Globetrotter ( https://www.dvmega.nl/globetrotter/ ) a remarkable device that contains an AMBE chip, enabling DMR, and with their recommended free BlueDV software ( http://www

the functionality is pretty good apart from a few minor annoyances the SWR displayed is way off, the radio shows SWR of 1.0-1.3 and the display in FLRig show 5:1 or more, the scaling just don't get ev

Hello all, I am new to the board and want to say Hello. I live in Connecticut and a long time ham, I am getting back into the hobby. I have a G90. I use it for digital modes (WSPR and JS8) with Ubuntu

Hi all Names Peter, I am in the southeast UK, and love to tinker with electronics, raspberry pi’s and radio (but not a programmer other than a bit of python on a Pi) Joined the group as I have a coupl

Hi Guys I have a new Xiegu X6100, and I have tried both the FLRig 1.4.7 GA, and the alpha releases The issues I have are Power slider don’t seem to work (setting or reading power level) Unable to init

Friends and fellow hams, I will be at the Stone Mountain Hamfest tomorrow at 11AM in the big forum room with a MAJOR ANNOUNCEMENT for HamPi. I'll drop one hint: four See you tomorrow! 73, -Dave P.S. A

I haven't use flrig for a while, so I downloaded and installed it today hoping to use Olivia. My setup is a MacBook Air M1 running Ventura. The radio is a Yaesu FT-891. In flrig Config > Xcvr I can co

I am having a problem getting flrig / fldigi to work on my iMac HS and Ten Tec Eagle. It will not revert to Rx from ‘tune’ or sending a text macro and the Tx light stays on. 73 de John K7JHM

Is there anyone in the Group using a RigBlaster Advantage and ICOM 7300 combination for PSK31 The Problem I am having is I don't see any output on the screen I'm sure it has to do with the Settings If

Anyone have any luck with software to upload qso’s from fldigi to Maclogger DX. Was using one by K3DCW with apple script but quit working after a crash and have no luck getting it to work again. Thank

http://www.w1hkj.com/alpha/flrig/ flrig-1.4.7.40.tar.gz 2022-10-19 11:03 1.0M flrig-1.4.7.40_BS.dmg 2022-10-19 11:03 3.9M flrig-1.4.7.40_HS.dmg 2022-10-19 11:03 2.3M flrig-1.4.7.40_LI.dmg 2022-10-19 1

Alright, team...this one really has me stumped... Fldigi 4.1.23 built from source using KM4ACK's Build-A-Pi script on a RPi4 4GB coupled with a Digirig audio interface (but same problem with both an E

uBitX v6 flrig failure uBitX v6.1 will not connect to flrig 1.3.49 emulating a Yaesu FT-817 under Ubuntu 20.04 I see comments about this failure but no solutions on groups.io. I am posting it on both

I am getting the following error in FLrig when i try to run WSJTX: Hamlib error: Invalid parameter rig_get_freq(2294): freqMainB=0, modeMainB=, widthMainB=0 rig_get_freq: elapsed=0ms rig.c(2297):rig_g