|
SNMP value for KEEPALIVED-MIB::vrrpInstanceWantedState 3 messages
Hi: I’m playing around with the SNMP values reported in the MIB for the state of VRRP instances, and I’ve noticed in the master LB that: If the master LB is OK and the associated vNIC of a VRRP instan
Hi: I’m playing around with the SNMP values reported in the MIB for the state of VRRP instances, and I’ve noticed in the master LB that: If the master LB is OK and the associated vNIC of a VRRP instan
|
By
Viton, Pedro (Nokia - ES/Madrid)
·
|
|
SCTP with multihoming 5 messages
Hello, All! Does anybody know if keepalived supports SCTP multihoming in load balancing scenarios? I try SCTP traffic balancing and it works ok, but while disabling some IPs traffic is routed to anoth
Hello, All! Does anybody know if keepalived supports SCTP multihoming in load balancing scenarios? I try SCTP traffic balancing and it works ok, but while disabling some IPs traffic is routed to anoth
|
By
here.be.dragonz@...
·
|
|
Correct way to configure IPv4 + IPv6 VRRP 2 messages
What will be the best way to configure both IPv4 and IPv6 VRRP in the same interface in case I want to be able to have interoperability between keepalived and devices with proprietary VRRP realisation
What will be the best way to configure both IPv4 and IPv6 VRRP in the same interface in case I want to be able to have interoperability between keepalived and devices with proprietary VRRP realisation
|
By
tad1866@...
·
|
|
Can IPv6 be labled? 4 messages
Is there any way for IPv6 in 'virtual_address' to be labled is such way that it would be visable via 'ip address show' but without acutally using IPv6 label functional (RFC3484). I want some kind of i
Is there any way for IPv6 in 'virtual_address' to be labled is such way that it would be visable via 'ip address show' but without acutally using IPv6 label functional (RFC3484). I want some kind of i
|
By
tad1866@...
·
|
|
Where is the official installation documentation of Keepalived software
Where is the installation documentation for the Keepalived2.2.* version
Where is the installation documentation for the Keepalived2.2.* version
|
By
滕可鑫
·
|
|
VRRP track_interface failover when system has multiple interfaces 4 messages
Hi, I have HA pair with interfaces eth0, eth1, eth2 and eth3, I have created VRRP instances for each interface and grouped them in VRRP sync group. I have also added track_interface with all the inter
Hi, I have HA pair with interfaces eth0, eth1, eth2 and eth3, I have created VRRP instances for each interface and grouped them in VRRP sync group. I have also added track_interface with all the inter
|
By
rasileti@...
·
|
|
ipvs rule not been cleanup when keepalived enter FAULT state
hi,i'm useing snat+keepalived to deploy a HA system, but found that keepalived does not cleanup ipvs rule when it enter FAULT state. it that normal? here is log,after i reload keepalived with kill -HU
hi,i'm useing snat+keepalived to deploy a HA system, but found that keepalived does not cleanup ipvs rule when it enter FAULT state. it that normal? here is log,after i reload keepalived with kill -HU
|
By
q1875486458@...
·
|
|
Is posibble to route all outgoing traffic from servers over VIP? 3 messages
Hi, I'm running a process on both master and backup, which sends periodically a test data over UDP, but I want to let go out the data only from master. on the test server I'm receiving data from both,
Hi, I'm running a process on both master and backup, which sends periodically a test data over UDP, but I want to let go out the data only from master. on the test server I'm receiving data from both,
|
By
fpinilla@...
·
|
|
SMTP alert issue after upgrade
I run keepalived on and between two Debian Linux hosts. Recently upgraded both hosts from Debian 9, running keepalived v1.3.2, to Debian 10, running keepalived v2.0.10 (versions supplied by Debian) Af
I run keepalived on and between two Debian Linux hosts. Recently upgraded both hosts from Debian 9, running keepalived v1.3.2, to Debian 10, running keepalived v2.0.10 (versions supplied by Debian) Af
|
By
keepalived@...
·
|
|
Keepalived: Both servers are set to master 3 messages
I am carrying out a project that requires failover management to guarantee the high availability of a process running on two servers. I decided to use Keepalived due to its apparent ease of configurat
I am carrying out a project that requires failover management to guarantee the high availability of a process running on two servers. I decided to use Keepalived due to its apparent ease of configurat
|
By
fpinilla@...
·
|
|
watchdog restart of keepalived_vrrp makes snmp unqueriable 4 messages
Hi all, Running keepalived 2.2.7 in CentOS7 upgrdaded. Compiled with: ./configure --enable-snmp --enable-snmp-rfc --enable-sha1 --prefix=/usr --sysconfdir=/etc Running with: KEEPALIVED_OPTIONS="-D -x"
Hi all, Running keepalived 2.2.7 in CentOS7 upgrdaded. Compiled with: ./configure --enable-snmp --enable-snmp-rfc --enable-sha1 --prefix=/usr --sysconfdir=/etc Running with: KEEPALIVED_OPTIONS="-D -x"
|
By
Spiros Ioannou
·
|
|
Keepalived flushing ips before executing stop scripts
Hi, I am currently running Keepalived under debian bullseye : - linux kernel version 5.10.103-1 - keepalived version 2.1.5 Here is the config used global_defs { notification_email { READACTED } notifi
Hi, I am currently running Keepalived under debian bullseye : - linux kernel version 5.10.103-1 - keepalived version 2.1.5 Here is the config used global_defs { notification_email { READACTED } notifi
|
By
shirenn
·
|
|
vrrp_sync_group one instance failure doesn't trigger group STATE change. 2 messages
When Instance1 in my BACKUP machine vrrp group fails to receive VRRP packets from active peer, it logs the error message "Receive advertisement timeout" but it is not triggering the group fail-over to
When Instance1 in my BACKUP machine vrrp group fails to receive VRRP packets from active peer, it logs the error message "Receive advertisement timeout" but it is not triggering the group fail-over to
|
By
jayadev.kumar@...
·
|
|
Received advert with lower priority, forcing new election 5 messages
Hello. I'm trying to configure a primary-standby pair of nodes for postgresql. The master node seems to work fine on its own, but when the backup comes online it steals the master role despite having
Hello. I'm trying to configure a primary-standby pair of nodes for postgresql. The master node seems to work fine on its own, but when the backup comes online it steals the master role despite having
|
By
danieleb@...
·
|
|
Updating from v2.0.10 to v2.2.7 11 messages
Hi there, I have been running Keepalived to allow my Pi-hole DNS server to be HA… it’s worked amazingly well without fail but I realised I am quite some version behind now. I am running v2.0.10 on 2x
Hi there, I have been running Keepalived to allow my Pi-hole DNS server to be HA… it’s worked amazingly well without fail but I realised I am quite some version behind now. I am running v2.0.10 on 2x
|
By
Jack Carter
·
|
|
Warning - script is not used 7 messages
Hi. My track_script doesn't seem to be getting used. The log I'm getting is `Warning - script chk_adguard is not used`. I'm sure this is a misconfiguration, but don't know how to fix. Here's my config
Hi. My track_script doesn't seem to be getting used. The log I'm getting is `Warning - script chk_adguard is not used`. I'm sure this is a misconfiguration, but don't know how to fix. Here's my config
|
By
Anthony Nash
·
|
|
Weight is 0, But the Realserver Gets New Connections Anyway... What? 2 messages
We have been using LVS + keepalived for a long time successfully until today. Suddenly we have realservers where we set the weight to 0 and people can still connect to them. We have to remove the real
We have been using LVS + keepalived for a long time successfully until today. Suddenly we have realservers where we set the weight to 0 and people can still connect to them. We have to remove the real
|
By
Eric Robinson
·
|
|
Is it possible to manually force a failover when the versions don't match? 8 messages
Is it possible to force a failover between a primary node currently running Keepalived v1.3.9 and a secondary node running Keepalived v2.2.2? I'm upgrading my load balancers to new OS and software ver
Is it possible to force a failover between a primary node currently running Keepalived v1.3.9 and a secondary node running Keepalived v2.2.2? I'm upgrading my load balancers to new OS and software ver
|
By
Chaffy
·
|
|
Get list of nodes in a cluster 2 messages
Hello, I am new to keepalived. May i know if there is a notify script which tells me when a node is added/removed from a cluster with all details? My use case is below: 1)Initially add a node as MASTE
Hello, I am new to keepalived. May i know if there is a notify script which tells me when a node is added/removed from a cluster with all details? My use case is below: 1)Initially add a node as MASTE
|
By
linga.kartheek@...
·
|
|
Keepalived v2.0.10 not setting IP as secondary 2 messages
Hi guys, new to this group. We are using keepalived in multiple pair of servers forming multiple pair of clusters. Just today I added on an existing cluster a new HA IP on a different interface than t
Hi guys, new to this group. We are using keepalived in multiple pair of servers forming multiple pair of clusters. Just today I added on an existing cluster a new HA IP on a different interface than t
|
By
liormmm@...
·
|