Date   
Re: Mmr 40

Wm David Collins
 

I saw it on Hendricks web site but it was discontinued. I emailed him and he had one more laying around that he sold to me. I've yet to build it. Maybe I'll  bring it out and build it up!
David, N4WDC


Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: "dyerhard1972 via Groups.Io" <Dyerhard1972@...>
Date: 5/8/19 16:23 (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mmr 40

It's a ssb/cw transceiver designed by steaven.  It's on his web page you should check it out. You can build it dead bug style or make a pcb or get a kit. It's out put is about 5 watts and it has a pto instead of a vfo.
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/8/19 2:25 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mmr 40

Please excuse the stupid question: what is a MMR 40?
  - 73, John

On 5/7/2019 7:34 PM, dyerhard1972 via Groups.Io wrote:
Has anyone built the mmr 40 qrp transceiver dead bug style and if so what were your thoughts about it when finished?  I'm thinking of taking on the project. Thanks
Jeff ke4fwe 

Re: Mmr 40

Norm. N7NSD
 

I have an unbuilt kit that I would be willing to sell if you are interested. 

Re: Mmr 40

dyerhard1972
 

It's a ssb/cw transceiver designed by steaven.  It's on his web page you should check it out. You can build it dead bug style or make a pcb or get a kit. It's out put is about 5 watts and it has a pto instead of a vfo.
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/8/19 2:25 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mmr 40

Please excuse the stupid question: what is a MMR 40?
  - 73, John

On 5/7/2019 7:34 PM, dyerhard1972 via Groups.Io wrote:
Has anyone built the mmr 40 qrp transceiver dead bug style and if so what were your thoughts about it when finished?  I'm thinking of taking on the project. Thanks
Jeff ke4fwe 

Re: Mmr 40

 

John,

https://www.qrpkits.com/mmr40.html

Its a tough build but it was fun.
--
73

David

N8DAH

Shop.Kit-Projects.com

Re: Mmr 40

John N0TA
 

Please excuse the stupid question: what is a MMR 40?
  - 73, John

On 5/7/2019 7:34 PM, dyerhard1972 via Groups.Io wrote:
Has anyone built the mmr 40 qrp transceiver dead bug style and if so what were your thoughts about it when finished?  I'm thinking of taking on the project. Thanks
Jeff ke4fwe 

Re: Mmr 40

dyerhard1972
 

How did the dds vfo work out I have the parts to make one. I didn't think of it as an option. I bet it makes a big difference making use easy. 
Thanks jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: ajparent1/kb1gmx <kb1gmx@...>
Date: 5/8/19 12:04 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mmr 40

You can get the manual from QRPkits as that will be more complete and updated from the QST article.

Good radio!  I deadbugged one for 20M but didn't use the VFO as I had the si5351 from generating
the LO

Allison

Re: Mmr 40

ajparent1/kb1gmx
 

You can get the manual from QRPkits as that will be more complete and updated from the QST article.

Good radio!  I deadbugged one for 20M but didn't use the VFO as I had the si5351 from generating
the LO

Allison

Mmr 40

dyerhard1972
 

Has anyone built the mmr 40 qrp transceiver dead bug style and if so what were your thoughts about it when finished?  I'm thinking of taking on the project. Thanks
Jeff ke4fwe 

Re: Mtr3b kit problem

dyerhard1972
 

Yes I have tried several different paddles. I think it's the chip. Thanks
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Bill Noyce <wbnoyce@...>
Date: 5/2/19 11:09 AM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Did you try it with your paddle plugged in?  Maybe there's an issue with the jack, the plug, or the paddle itself.

On Thu, May 2, 2019, 10:54 AM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.

AGC mod for ATS4A

Lloyd K3ESE
 

has anyone documented one?

Re: Mtr3b kit problem

John N0TA
 

In that case, it would probably be best to wait until Steve is back.
  - John

On 5/2/2019 4:03 PM, dyerhard1972 via Groups.Io wrote:
I think I can manage to change it out but I have no way to program the chip. My computer skills are less than marginal. Hopefully I can Grace someone's paypal and I can get a programmed chip. Thanks for the help and info.
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 3:58 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
I have always used a small nozzle, and kept it directed at the component I need to remove - has worked for me. You probably will not need to add too much (if any) new paste for the new chip.

The processor is available from Mouser, and probably the other suppliers, too; however, you will still need to upload the firmware. I have fixed another MTR with a similar problem, so it is not too unusual.

Good Luck!
  - John


On 5/2/2019 10:13 AM, dyerhard1972 via Groups.Io wrote:
John that would be great. It will be difficult to remove but I have done similar things before I'll just cut a hole in a peace of aluminum foil and tape it over the part so I don't blow other parts off with the hot air. Thanks
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 11:52 AM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
Sounds like you need a new processor. This involves a new chip AND installing the firmware.

When Steve returns, he can probably prepare a processor for you with firmware. If this doesn't work out, please contact me, and I'll try to help. There are others on the list that can do this as well.
Good luck,
  - John, N0TA


On 5/2/2019 8:54 AM, dyerhard1972 via Groups.Io wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.



ATS4A v ATS4B

Lloyd K3ESE
 

... what is the difference?

thanks, in advance.

Re: Mtr3b kit problem

Bill Noyce
 

Did you try it with your paddle plugged in?  Maybe there's an issue with the jack, the plug, or the paddle itself.


On Thu, May 2, 2019, 10:54 AM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.

Re: Mtr3b kit problem

dyerhard1972
 

I think I can manage to change it out but I have no way to program the chip. My computer skills are less than marginal. Hopefully I can Grace someone's paypal and I can get a programmed chip. Thanks for the help and info.
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 3:58 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
I have always used a small nozzle, and kept it directed at the component I need to remove - has worked for me. You probably will not need to add too much (if any) new paste for the new chip.

The processor is available from Mouser, and probably the other suppliers, too; however, you will still need to upload the firmware. I have fixed another MTR with a similar problem, so it is not too unusual.

Good Luck!
  - John


On 5/2/2019 10:13 AM, dyerhard1972 via Groups.Io wrote:
John that would be great. It will be difficult to remove but I have done similar things before I'll just cut a hole in a peace of aluminum foil and tape it over the part so I don't blow other parts off with the hot air. Thanks
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 11:52 AM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
Sounds like you need a new processor. This involves a new chip AND installing the firmware.

When Steve returns, he can probably prepare a processor for you with firmware. If this doesn't work out, please contact me, and I'll try to help. There are others on the list that can do this as well.
Good luck,
  - John, N0TA


On 5/2/2019 8:54 AM, dyerhard1972 via Groups.Io wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.


Re: Mtr3b kit problem

John N0TA
 

Jeff,
I have always used a small nozzle, and kept it directed at the component I need to remove - has worked for me. You probably will not need to add too much (if any) new paste for the new chip.

The processor is available from Mouser, and probably the other suppliers, too; however, you will still need to upload the firmware. I have fixed another MTR with a similar problem, so it is not too unusual.

Good Luck!
  - John


On 5/2/2019 10:13 AM, dyerhard1972 via Groups.Io wrote:
John that would be great. It will be difficult to remove but I have done similar things before I'll just cut a hole in a peace of aluminum foil and tape it over the part so I don't blow other parts off with the hot air. Thanks
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 11:52 AM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
Sounds like you need a new processor. This involves a new chip AND installing the firmware.

When Steve returns, he can probably prepare a processor for you with firmware. If this doesn't work out, please contact me, and I'll try to help. There are others on the list that can do this as well.
Good luck,
  - John, N0TA


On 5/2/2019 8:54 AM, dyerhard1972 via Groups.Io wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.


Re: Mtr3b kit problem

dyerhard1972
 

John that would be great. It will be difficult to remove but I have done similar things before I'll just cut a hole in a peace of aluminum foil and tape it over the part so I don't blow other parts off with the hot air. Thanks
Jeff ke4fwe 



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: John N0TA <reillyjf@...>
Date: 5/2/19 11:52 AM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

Jeff,
Sounds like you need a new processor. This involves a new chip AND installing the firmware.

When Steve returns, he can probably prepare a processor for you with firmware. If this doesn't work out, please contact me, and I'll try to help. There are others on the list that can do this as well.
Good luck,
  - John, N0TA


On 5/2/2019 8:54 AM, dyerhard1972 via Groups.Io wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.

Re: Mtr3b kit problem

John N0TA
 

Jeff,
Sounds like you need a new processor. This involves a new chip AND installing the firmware.

When Steve returns, he can probably prepare a processor for you with firmware. If this doesn't work out, please contact me, and I'll try to help. There are others on the list that can do this as well.
Good luck,
  - John, N0TA


On 5/2/2019 8:54 AM, dyerhard1972 via Groups.Io wrote:
Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.

Re: Mtr3b kit problem

dyerhard1972
 

Ok I took the back off this morning but the more i think about it the more i confuse myself. Here are the measurements I got.
Dit to dah 76k ohm power on 5.8m power off.
Dah to g 10.6m power on open power off.
Dit to g open both power on off. So if day is at 10.6m ohms to ground power on that's not enough to be short? So my chip would seem to be the issue. Correct??? Damn esd.
Jeff ke4fwe  



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced. 

Steve kd1jv 

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:

My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe 


Sent from my Samsung Galaxy smartphone.

searching MTR3B !!!! someone selling?

Carlos Tomazelli
 

Hello guys,
I'm looking for someone to have a Mountain Topper MTR3B CW, used, mounted or to mount.
Please send direct contact carlos_tomazelli@...

I'm in Brazil, PY2CSU .... 73

Re: Mtr3b kit problem

Jer Tres
 

i would suspect if LNR is still selling them (looks like they are),
then probably the processor is still around

On Wed, May 1, 2019 at 1:38 PM dyerhard1972 via Groups.Io
<Dyerhard1972=yahoo.com@groups.io> wrote:

If the processor needs to be replaced are they available? Thanks
Jeff



Sent from my Samsung Galaxy smartphone.

-------- Original message --------
From: Steven Weber <steve.kd1jv@...>
Date: 5/1/19 1:23 PM (GMT-05:00)
To: kd1jvdesigns@groups.io
Subject: Re: [kd1jvdesigns] Mtr3b kit problem

If the dash input is low, it goes into straight key mode. There could be a short to ground or the port is blown and the internal pull up not working. If the later, the processor needs to be replaced.

Steve kd1jv

On Wed, May 1, 2019, 12:41 PM dyerhard1972 via Groups.Io <Dyerhard1972=yahoo.com@groups.io> wrote:


My name is jeff ke4fwe and I have a question for the group. Several month's ago I found an inbuilt mtr kit on ebay that I purchased and built. It all works great with one exception it won't go into paddle mode. It was the middle of winter so I set it aside. Well now the weather is nice and I would like to use it. I studied the schematic and found the dash goes to pin 9 of chip u10 strait shot. I believe this issue has two possible problems a bad plug and I have tried several different paddles. The other would be a bad and or miss programmed u10 chip. Has anyone had a similar issue? I plan on taking it apart and checking the plug for continuity this weekend. I hope it's the plug.
Jeff ke4fwe


Sent from my Samsung Galaxy smartphone.