Has anyone out there figured out a way to connect a Bluetooth headset (ie Jabra) to the ic-7000? I suppose the rx would be easy enough just using a Bluetooth adapter to the audio out (earphone jack).

How do I get the power cable off of the unit? Squeeze on the sides of the connector as much as I can it won't budge.

Never even thought about it before but had a tune around the airband AM bands and the 7000 sounds quite nice, although was only using my 6 el Yagi pointed at Stansted Airport and on the approach frequ

Well wit a discontinued radio it won't be resolved by Icom, but what is the issue?

I just tried it at full power on 20m, and using the built-in bar meter for all observations: * Carrier-only level was 40%. * Normal voice peaks were below 50% with a slightly loud voice and the mic. g

I’ve been thinking to swap my KWD TM-710G out for a used IC-7000 in my QuickSilver Radio Hammo-Can Go-Box for use with Winlink and ARES work. I’d use it either 2m or 40m/80m HF. I’d have to add a Sign

I purchased a UD01IC cable to connect my IC7000 and IC706 to my raspberry pi running fldigi. The audio transfers back and forth fine, but it will not trigger the ppt. The instructions say to use the r

The first two digits of the serial # are the country code, which mostly signifies what feature diode configurations that were shipped from the factory to determine allowable frequency coverage. 30 & 1

Noticed the following listing on ebay. *ICOM - OPC-1444 Separation Cable for The Icom IC-7000 Transceiver. * I see that this seller Joslyn1980 has sold a few going by positive feedback. So anyone that

As far as I know, there is no firmware update for the 7K. 73, Jeff/wb0m

Just saying, for a few bucks, you can get a 3.5mm to RCA adapter and not have to cut, solder, destroy, the HDMI to RCA cable... 73 Dallas, KD4HNX Whatever you do, don’t fall victim to “paralysis by an

Paul, Try Kenwood mic cords. For the V71, for example. Same pinout as ICOM and high quality. I use one on my 7000. Steve 73 DE KC4SM Aug 12, 2020 9:03:31 AM Paul <pg321@...>:

Hi Paul, I am new on this group so need littel guide. thank you for your inputs. could you supply with some links to how to make these mods. Where to find instructions how to do these mods, where do I

Anyone using Chirp for programming the memories? I've downloaded the memories and saved to a CSV but I can't figure out how to do the different banks. A1 bank is the only successful bank downloaded an

Greetings all, A little off topic for IC7K . . . but was operating FD from my truck on outboard batteries but when it started to get hot hooked up an electric fan via a Harbor Freight inverter. The ha

People still believe the false flag hoax of nothing more than influenza?Why is it in a Amateur Radio group anyways?Please unsubscribe me from this hocus pocus fabricated fiction.

Hello group, I cannot control my 7000 via cat. It's been 10 years since i tried it since I had it mobile all the time. I have a rig blaster plug and play and that works on my 7610 and Yaesu FT817ND, b

Hi guys I’m repairing an IC-7000, I put 2 new finals RD70HHF1 and I set bias 100% (1 A for each final) But I have a strange behaviour ; the power goes up slowly, for example if I set 100 watt , power

OK Guys, the new Bluetooth CT-17B-6BT is now available and so is the new CT-17B-6USB VERSION 2 with detachable USB cable for more information see WWW.VE2DX.COM. -- 73 Richard VE2DX, Jesus Island, PQ-0

Hi guys I’m repairing an IC-7000, I put 2 new finals RD70HHF1 and I set bias 100% (1 A for each final) But I have a strange behaviour ; the power goes up slowly, for example if I set 100 watt , power