Hi all I’m have a problem when I go to hf. Every once In a while channel A has HF but what I don’t get is. It will receive on HF and transmit on 2meters. WhT I like to know is how in the hell do I sto

I know of two ICOM &K receivers, neither in working condition, for sale. Any idea what the value of each is. Faults are unknown at this time. Any suggestions would be appreciated. Thank You 73's Dwigh

Hi all I was with a fellow ham and he asked me a question on my Ic7000. So I’m going to ask here. Can the IC-7000 be put into dual band repeat ?

Hello all, I have an issue with my recieve and i hoping someone has ran into this before with a solution. I suspect the ribbons are bad by what I've researched on different forums and videos. The reci

Hi all. I am very pleased and now informed with the many feedback I received in regard to the 2.5A power supply. Thanks again. My radio came in English but translated from Japanese. I user manual. I h

You can use the mike jack and speaker jack to connect the radio to the computer. You should use some sort of isolation, such as transformers. I am at the same juncture that you are at setting up a dig

Hi all I’m looking for video cable for my ic7000. I’m trying to get a video to a 10 inch monitor. The video plug on the monitor is a female RCA plug. So I’m in search for a good cable. Thanks to every

Hi all, Can I use a 110/230 to 13.8V out , 2.5A as a power supply unit for my Ic-7000? Thanks *********************** A. Eddie Mobasheri 46 Bollard Avenue New Windsor 0600 Auckland, NZ Ph: +64 0212 (P

Ah, the wonders of the SET mode.

Hi all… I’m wanting to do some tx audio checks on an HT and the only other rig I have that covers 2m is the ic 7000. I fired it up and -for the first time ever- put it on 2m. Trouble is, I can’t get i

I have an IC7000 that has problems with the ALC circuit. The ALC voltage is about 3 volts unless USB or LSB is selected and then it drops to 0 and no output. The ALC is pegged and no power out. I foun

Undoubtedly, everyone is aware of the IC-7K's dependence on input voltage. In my 2016 F-150, the computer decides how much power the alternator puts out. Gone are the days of constant 13.7 Volts. The

Am using the 7000 for FT8 and using the accessory socket to interface to the pc via a commercial interface lead (am not using CI-V) everything works on all the HF bands including 50Mhz no problems but

Hi to all! I am wondering how can I get hands on one separation cable ( Icom Ic-opc-1443, 3.5m). Even a working second hand will do me! I am in Auckland, New Zealand. Kind regards Eddie Mobasheri ZL1A

My "fixed" IC7000 has a transmit problem. It seems to be OK on receive but on SSB the ALC pegs with even the least audio and it puts out no RF power. On RTTY, CW, etc it seems to put out too mucheap p

I have my 7000 mounted in my car. I have noticed that when the temperature is below freezing, my 7000 is deaf on 80 meters when I first turn it on. I have also noticed that the receive kicks right in

In speaking to Randy at Timewave they also have a cable using the data port and not the ACC. Since no one has answered me on three reflectors, I am guessing no one is using the Navigator/7000 and PW-1

I couldn't find exactly what I needed in past messages. I googled it and also checked eBay. I want to add my IC-7800 to my PW-1. I currently have the 7800 connected. Who makes the cable for this? I ne

Anyone use this combination with an MFJ 1708 antenna switch. Thoughts? Is there a setup configuration? 73 Bill VA3QB

Hello Any idea why power output is set to 100W, I can measure this on external power meter and a dummy load, BUT the display of IC-7000 shows only 25W? Any idea appreciated. 73! Adi/YO2LIW