My name is Jim Walker My call is KBØX I just purchased a used IC-7000 and would like to find out how to go about modifying the radio to connect an external video monitory to it. Thanks, Jim

I'd like to be a member if' I'm not already one............was at the yahoo. groups place. Thanks, Craig, N6BWJ ccclifton@...

W3 8900015210 CBL OPC-1448A (P0.5, N28, L60) Main board to PA W4 8900015210 CBL OPC-1448A (P0.5, N28, L60) Main board to PA W5 8900015220 CBL OPC-1461A (P0.5, N30, L40) Main board to DDS W6 8900015220

I have been working on my second IC-7000 from the scrap pile with the Click - Click no power problem. My problem is that the main board has been out so many times that the ribbon cable from the main b

Does the 7000 require any firmware updates? Checked Icom website but did not see any info. Tnx, 73 K0CRI

Hi all I’m new to this group so please for give me on this post. In gone thru the manual and can not find how to get this radio to scane at 5 MHz insted of the 10mhz. So if some one out there can tell

Hello Fellow 7K-ers, Page 135 of the manual there is a diagram of an external keypad that activates the contents of voice memories. Saw this: https://www.sotabeams.co.uk/contestconsole-switching-unit-

Looking to replace my trusty IC-7000 with a DC-to-Daylight rig with digital in it. Before going the eBay or eHam route, wanted to offer it to the group. I'm the original, non-smoking owner. Rig has sp

When using the Icom 7000 with the Icom RS-BA1 software, will the software work with the 7000 to send the CW messages programmed with the software. That is, does the RS-BA1 work with the Icom 7000 to c

Hi i am Mike and i am a Amateur radio operator. I had to move in to a apartment building and I tried my HT yaesu ft-60 and then I was told not to do it I know I can do it with in my rights but I have

This thread is screwy from the start. Not normal vernacular from a ham. My 2 cents. 73- W1JCW John From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of D C *Mac* Macdonald Sent: Wednesday, Se

Hello, my 7000 is connected to the radio port of a MFJ-993B tuner. Unfortunately, the tune button on the 7000 does not trigger the low power keying of the transmitter. The TUNE message on the display

Hi i am Mike and i am a Amateur radio operator. I had to move in to a apartment building and I tried my HT yaesu ft-60 and then I was told not to do it agen I know I can do it with in my rights but I

Hi Jim, my ic7000 has problems, when I change band with the up or down button and step from the bands hf to vhf it stops working and crashes. Switching from 29.999 mhz to 30 mhz the monitor goes off a

Group, I’ve recently lost the ability to communicate between my 7000 and HRD using the RTS-01 cable. I checked the voltage on the CI-V and have about 2.5v. An Icom rep tells me that is where it’s supp

Looking to replace the PTT switch on my HM 151. Does someone have a source for these switches ?? 73- W1JCW John

Digi-Key (450-1804-ND). 73- W1JCW John From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of W1JCW Sent: Tuesday, July 17, 2018 8:24 AM To: ic7000@groups.io Subject: [ic7000] PTT switch source

All, Several weeks ago I took my IC-7000 to Galveston and used it to activate the Tall Ship Elissa for Museum Ships Weekend. Our station was setup on the pier along side the ship under an awning. Brig

I hope this is a stupid question with a simple answer. My F1 F2 F3 and F4 buttons do not seem to be functioning. Did a factory reset and still nothing. Have read the manual back to front but still not

Hello all. since Yahoo is gone io is taking over please and hello to all.