I have no problems with accessing and controlling my ICOM 7000 radio using HRD Rig Control. What I am not able to do is get the memory management to work with HRD. I have tried some other software for

Greetings to all: see lots of posts using CAT with the 7000 and ACLog - presumably for rig control. I have been using RigRunner very nicely. However, nothing so far about an interface to connect the 7

Hello everyone. I have an Icom 7000 that now shows a high SWR (2:1 - 3:1) depending on band into a dummy load (2 different ones). Here's the catch, I can change the SWR by using different lengths of c

Hi guys , I have a new ( well it was in 2005) 7000 , still in the box want to get it up and running Can someone suggest the upgrades that I might usefully do , firmware , hardware etc. ive lost track

Hi everyone Im trying to do the chirp thing The computer and radio are talking However because its a live input do you have to manually input everything Or is there another way Also does anyone know o

Good Evening Bret. I'm going to take a guess that no one has replied because this group deals with the IC-7000, not the IC-7100. And, they are different radios. You might try using your web browser an

Does anyone know of a video on how to change the VHF/UHF Mosfet power amp ? Would like to review it before attempting.

Has anyone out there figured out a way to connect a Bluetooth headset (ie Jabra) to the ic-7000? I suppose the rx would be easy enough just using a Bluetooth adapter to the audio out (earphone jack).

How do I get the power cable off of the unit? Squeeze on the sides of the connector as much as I can it won't budge.

Never even thought about it before but had a tune around the airband AM bands and the 7000 sounds quite nice, although was only using my 6 el Yagi pointed at Stansted Airport and on the approach frequ

Well wit a discontinued radio it won't be resolved by Icom, but what is the issue?

I just tried it at full power on 20m, and using the built-in bar meter for all observations: * Carrier-only level was 40%. * Normal voice peaks were below 50% with a slightly loud voice and the mic. g

I’ve been thinking to swap my KWD TM-710G out for a used IC-7000 in my QuickSilver Radio Hammo-Can Go-Box for use with Winlink and ARES work. I’d use it either 2m or 40m/80m HF. I’d have to add a Sign

I purchased a UD01IC cable to connect my IC7000 and IC706 to my raspberry pi running fldigi. The audio transfers back and forth fine, but it will not trigger the ppt. The instructions say to use the r

The first two digits of the serial # are the country code, which mostly signifies what feature diode configurations that were shipped from the factory to determine allowable frequency coverage. 30 & 1

Noticed the following listing on ebay. *ICOM - OPC-1444 Separation Cable for The Icom IC-7000 Transceiver. * I see that this seller Joslyn1980 has sold a few going by positive feedback. So anyone that

As far as I know, there is no firmware update for the 7K. 73, Jeff/wb0m

Just saying, for a few bucks, you can get a 3.5mm to RCA adapter and not have to cut, solder, destroy, the HDMI to RCA cable... 73 Dallas, KD4HNX Whatever you do, don’t fall victim to “paralysis by an

Paul, Try Kenwood mic cords. For the V71, for example. Same pinout as ICOM and high quality. I use one on my 7000. Steve 73 DE KC4SM Aug 12, 2020 9:03:31 AM Paul <pg321@...>:

Hi Paul, I am new on this group so need littel guide. thank you for your inputs. could you supply with some links to how to make these mods. Where to find instructions how to do these mods, where do I