Date   

Re: spares

 

What is the issue with your board?


Re: spares

MICHAEL WILDER
 

board


IC-7000 + IT-100 for sale

Dennis Haarsager <haarsager83843@...>
 

Icom IC-7000 multimode HF + 50, 144, 430 MHz transceiver. Only a couple of hours use in like-new condition. $725 plus shipping. LDG Electronics IT-100 tuner plus cable for IC-7000. Never used. $120 plus shipping. Manuals for both. Non-smoking household. Buy together and I'll pay USPS shipping in U.S.

I'm OK in QRZ.

73, Dennis L. Haarsager, N7DH
Kittery Point, Maine, USA


Re: spares

Prabhu
 

Do you need display alone or board?

On Wed, 17 Feb 2021 at 11:04, MICHAEL WILDER via groups.io <mewilder901=yahoo.com@groups.io> wrote:
Looking for the remote head, very minimum, I am needing the display unit board in side.


Re: spares

MICHAEL WILDER
 

Looking for the remote head, very minimum, I am needing the display unit board in side.


Re: Mic cable

Bill Storey
 

I have two of the mics, both with faulty cables.  I bought four on Amazon, two replacements and two spares.  They seem to be holding up well.

Bill

Sent from my shoe phone’s big brother.  Please excuse auto connections caused by typhoons.  


Re: CT-39 Cable

Jim Farley, KG4FXV
 

Doug --

HRO(Ham Radio Outlet) has a Yaesu CT-39 cable with a 6-pin mini on one end and bare wires on the other end at $9.95 US.

AMAZON has a Yaesu CT-39A cable with a 6-pin mini on one end and bare wires on the other end at $17.88 US, and a good selection of DB-9 connectors, male and female, solder types and breakout types, at seemingly reasonable prices.

Shipping across the US/Canada border will, I am sure, add some other fees/taxes.

Hope this helps.

 
Jim Farley

JIM FARLEY
, KG4FXV
jimfarley@...
.



On Saturday, February 13, 2021, 10:04:20 AM EST, Doug Henry <doug.henry1@...> wrote:


Greetings, I'm looking for a source of a CT-39 cable (6 pin mini Din) with DB-9 connector attached for packet and Winlink use.

Thanks, Doug VE1ZG


Re: Mic cable

David Miller
 

Thanks for all the suggestions, I have one arriving tomorrow.

73 de NN4E


CT-39 Cable

Doug Henry
 

Greetings, I'm looking for a source of a CT-39 cable (6 pin mini Din) with DB-9 connector attached for packet and Winlink use.

Thanks, Doug VE1ZG


Re: Mic cable

Alan, AB6C
 

For what it's worth, you can use any standard ethernet cable (Cat 5e, etc). I realize that it's not a curly cord, or what is often called a heavy duty cable, but I've used that for years going mobile with my HM-151 mic. My cord is a FLAT (not curly) 14 foot long ethernet cable I bought on Amazon over 10 years ago, going from my 7000 head mounted in my glove compartment to the radio body mounted under the driver's seat, and it still works fine. That was a solution for me because I didn't have enough room for both the mic and the original cord that came with it in the glove compartment, and the ethernet cable lays flat and takes little room. I "bunch" it up so it also fits in the glove compartment when it's not in use. It works for me, and you probably have several spare ethernet cables in your home in these "online" days. Just a suggestion.

73, Alan, AB6C


Re: Mic cable

 

A quick search on eBay gives this first thing:
https://www.ebay.com/itm/DTMF-heavy-duty-mic-microphone-cable-cord-for-Icom-HM-151-IC-7000-IC-7100/273720215677?hash=item3fbaff087d:g:88UAAOSwVR5cbsXP


Re: Mic cable

W3DRM - Don
 

Find the part number from your documentation and then send an email to ICOM (Parts@...) and ask them for a price quote. They normally respond quite quickly. I was in need of a PTT switch and after several eBay failures, I went to ICOM. I should have just gone to them first.

 


Re: Mic cable

Jim Szalajeski
 

Have you tried ICOM?


On Friday, February 12, 2021, 8:46:32 PM CST, David Miller via groups.io <nn4e@...> wrote:


Does anyone know where I could source a replacement mic cable for my HM-151?  The curly one with RJ-45 ends.

Thanks and 73 de NN4E





Mic cable

David Miller
 

I found one on Amazon


Mic cable

David Miller
 

Does anyone know where I could source a replacement mic cable for my HM-151? The curly one with RJ-45 ends.

Thanks and 73 de NN4E


Is anyone using their IC-7000 for FSQ on VHF?

Chris - KC9AD
 

I recently discovered that my IC-7000 has the same 6-pin mini-DIN connector as my VHF/UHF Kenwood TM-V71A. So I took my FSQ/FLDIGI cable out of the Kenwood and plugged it into the IC-7000, tuned the rig to 145.580, our local FSQ watering hole frequency, and, VOILA!, FSQ on my IC-7000. Is there anyone else out there doing that? Especially in the Phoenix, AZ area?


Re: NO CAT Control IC-7000 using Winlink

Kevin Grantham
 

Winlink Express works fine with my IC-7000.

Check the Icom, not the early models. The frequency format is different.
Make sure the CI-V address is the same in the radio and in the Winlink setup - by the way, which mode are you using? You have to set it up for each of the HF modes you will use - ARDOP, VARA, etc.
Note that Winlink will not set the frequency for Packet or VARA FM modes.
You checked the baud rate - good.
The DTR/RTS setting is only important for some USB to CI-V adapters. Which adapter are you using?
Some CI-V adapters use old Prolific drivers and will not work with newer versions of Windows - you have to find the old driver and load it manually.
I don’t remember if “TRANCEIVE ON” has to be set in the IC-7000 for Winlink. It’s required for HRD so I have it on.

With those settings when you open a session in, say, ARDOP, and then select a station from the updated station list, the radio should switch to that frequency.

If that’s working, then make sure that PTT is set to use the CI-V method, not a aerial port. If that’s set up right then the radio should go into and out of transmit when you START the session.

The last step is to get the audio connected, if you haven’t already.

Good luck!

Kevin N5KRG


Re: NO CAT Control IC-7000 using Winlink

Steve Toquinto
 

OK! It took a Hard Reset of the CPU to get it working.
I tested it with the IC-7100 settings, Icom Amateur Radio's and Icom Amateur Radios (Early)
settings and disabled the RTS and DTR and they all work.

                     Tnx for the Help 73 de Steve KB6HOH


Re: NO CAT Control IC-7000 using Winlink

 

I used my IC-7000 a good bit with Winlink, no problem. 
Use the ICOM Amateur (not early) setting and the port and baud rate same as WSJT-X would. The audio needs to be the same as well.
If I remember correctly.


Re: NO CAT Control IC-7000 using Winlink

Helmut Wabnig
 

On Sun, 07 Feb 2021 03:51:17 -0800, you wrote:

Hello All,

I'm looking at putting my IC-7000 online as my Winlink HF Gateway.
There is NO Radio listing in RMS Express for the 7000. I have tried the Icom Amateur Radio's and the Early version as well.
I have the right CI-V# and Baud rate configured. I have turned on/off the RTS/DTR with no luck.
I have installed the FLdigi, FLrig control software and that works just fine.
Anybody out there that is using the IC-7000 and Winlink Express and or the Winlink Tri-Mode software.

73 de Steve KB6HOH

Winlink requires a "modem", which one do you select?
It is in the "open session" edit field.

w.

161 - 180 of 41342