Date   

Re: CAT settings help needed

Max
 

Since something is obviously different, I would check things like the voltage and for noise on the USB port.

Max KG4PID

On Tuesday, April 20, 2021, 11:32:19 AM CDT, Paula K7PAX via groups.io <hamette@...> wrote:


I have not even generated any RF at this point - all I am trying to do is connect HRD to the rig. Worked immediately and successfully when laptop is plugged into shore power, and I have used it that way for months. It simply will not work when the laptop is on battery. I even tried plugging the laptop into an inverter powered by a Milwaukee 18v battery, which powers the laptop just fine (delivering AC) but it still won’t make the USB port function enough to control the radio. When I plug it into the wall socket it works fine. I have scoured the internet for clues and haven’t found any solution that I haven’t already tried. 😟

Paula K7PAX

On Apr 20, 2021, at 8:45 AM, Glenn Jensen <WA6BJQ@...> wrote:



Hi Paula,

 

Is it possible that RF is getting into the USB ports…. I have to use a fair amount of ferrite here in the shack (and I suspect that it may be as challenging while portable).

 

Used a kit from Palomar Engineers – every single piece in the kit was used!  FT-8 / timing on JTDX and WSJT-X were very susceptible to drop-outs from RF messing with the USB and Audio ports.

73’s – Glenn

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Paula K7PAX via groups.io
Sent: Tuesday, April 20, 2021 8:21 AM
To: ic7000@groups.io
Subject: Re: [ic7000] CAT settings help needed

 

I was never successful getting CAT to work while portable. I discivered, when I returned home, that it would work correctly only with the laptop power cable plugged in. I checked all the buried power saving settings regarding USB power saving, and they are all appropriately disabled, including the USB root hub settings. 

So it is the laptop itself that is the problem. Don’t know where to go from here . . . 
--
Paula K7PAX


--
Paula K7PAX


Re: CAT settings help needed

Paula K7PAX
 

I have not even generated any RF at this point - all I am trying to do is connect HRD to the rig. Worked immediately and successfully when laptop is plugged into shore power, and I have used it that way for months. It simply will not work when the laptop is on battery. I even tried plugging the laptop into an inverter powered by a Milwaukee 18v battery, which powers the laptop just fine (delivering AC) but it still won’t make the USB port function enough to control the radio. When I plug it into the wall socket it works fine. I have scoured the internet for clues and haven’t found any solution that I haven’t already tried. 😟

Paula K7PAX

On Apr 20, 2021, at 8:45 AM, Glenn Jensen <WA6BJQ@...> wrote:



Hi Paula,

 

Is it possible that RF is getting into the USB ports…. I have to use a fair amount of ferrite here in the shack (and I suspect that it may be as challenging while portable).

 

Used a kit from Palomar Engineers – every single piece in the kit was used!  FT-8 / timing on JTDX and WSJT-X were very susceptible to drop-outs from RF messing with the USB and Audio ports.

73’s – Glenn

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Paula K7PAX via groups.io
Sent: Tuesday, April 20, 2021 8:21 AM
To: ic7000@groups.io
Subject: Re: [ic7000] CAT settings help needed

 

I was never successful getting CAT to work while portable. I discivered, when I returned home, that it would work correctly only with the laptop power cable plugged in. I checked all the buried power saving settings regarding USB power saving, and they are all appropriately disabled, including the USB root hub settings. 

So it is the laptop itself that is the problem. Don’t know where to go from here . . . 
--
Paula K7PAX


--
Paula K7PAX


Re: okay to list a 7000 for sale?

DogLover2
 

I think you just did by asking  😉

Jason MacDonald 



From: ic7000@groups.io <ic7000@groups.io> on behalf of Jamie WW3S <ww3s@...>
Sent: Tuesday, April 20, 2021 10:45:09 AM
To: ic7000@groups.io <ic7000@groups.io>
Subject: [ic7000] okay to list a 7000 for sale?
 
Is it permitted to post a IC-7000 for sale here? 


okay to list a 7000 for sale?

Jamie WW3S <ww3s@...>
 

Is it permitted to post a IC-7000 for sale here? 


Re: CAT settings help needed

Glenn Jensen
 

Hi Paula,

 

Is it possible that RF is getting into the USB ports…. I have to use a fair amount of ferrite here in the shack (and I suspect that it may be as challenging while portable).

 

Used a kit from Palomar Engineers – every single piece in the kit was used!  FT-8 / timing on JTDX and WSJT-X were very susceptible to drop-outs from RF messing with the USB and Audio ports.

73’s – Glenn

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Paula K7PAX via groups.io
Sent: Tuesday, April 20, 2021 8:21 AM
To: ic7000@groups.io
Subject: Re: [ic7000] CAT settings help needed

 

I was never successful getting CAT to work while portable. I discivered, when I returned home, that it would work correctly only with the laptop power cable plugged in. I checked all the buried power saving settings regarding USB power saving, and they are all appropriately disabled, including the USB root hub settings. 

So it is the laptop itself that is the problem. Don’t know where to go from here . . . 
--
Paula K7PAX


Re: CAT settings help needed

Paula K7PAX
 

I was never successful getting CAT to work while portable. I discivered, when I returned home, that it would work correctly only with the laptop power cable plugged in. I checked all the buried power saving settings regarding USB power saving, and they are all appropriately disabled, including the USB root hub settings. 

So it is the laptop itself that is the problem. Don’t know where to go from here . . . 
--
Paula K7PAX


Re: CAT settings help needed

Helmut Wabnig
 

On Sat, 17 Apr 2021 08:31:42 -0700, you wrote:

Hello - took my laptop and rig camping and wanted to operate digitally for a day or two. Haven’t used this laptop with the 7000 for a couple of years. When I attempted to set everything up, the CAT would not function. I believe the only thing different is the USB to serial adapter. I use a Keyspan, and the current one is newer than I used before, but the same model.  I also updated to the latest Keyspan driver. And the laptop was upgraded to Windows 10. To troubleshoot, I tried all the different combinations of DTR, RTS, and different baud rates on both software and rig. Tried from WSJT-X and HRD without success. I did notice at one point while troubleshooting, that at 4800 BAUD I did get some small response from the radio, but no successful connection.

Any and all suggestions welcome. This one has me scratching my head, and it is probably just something dumb - but I’d love to figure it out today while I am still in camp.
Usually when testing a serial interface one connects pin 2 and 3
on the serial port. The data must come back as I type them.

Maybe it works with the 7000 connector also?


w.


CAT settings help needed

Paula K7PAX
 

Hello - took my laptop and rig camping and wanted to operate digitally for a day or two. Haven’t used this laptop with the 7000 for a couple of years. When I attempted to set everything up, the CAT would not function. I believe the only thing different is the USB to serial adapter. I use a Keyspan, and the current one is newer than I used before, but the same model.  I also updated to the latest Keyspan driver. And the laptop was upgraded to Windows 10. To troubleshoot, I tried all the different combinations of DTR, RTS, and different baud rates on both software and rig. Tried from WSJT-X and HRD without success. I did notice at one point while troubleshooting, that at 4800 BAUD I did get some small response from the radio, but no successful connection. 

Any and all suggestions welcome. This one has me scratching my head, and it is probably just something dumb - but I’d love to figure it out today while I am still in camp. 
--
Paula K7PAX


IC-28H and 37A

paul makinen
 

I've got a couple of those nearly indestructible ICOM IC-28H and 37A VHF transceivers (146 and 220 MHz, respectively) from the 1980s, and have not been able to find any online fan groups for them.  I'm hoping someone here might be able to point me in the right direction...


Re: low power out on HF

Kurt Sweeny
 

Has anyone found a good replacement for the stock fuse holders? I am thinking of replacing the stock holders but would like to avoid a weak/ ugly wire to wire splice.

Kurt
KD6LZV

———————-

On Mar 31, 2021, at 8:10 AM, Mark Brueggemann via groups.io <qrq_cw=yahoo.com@groups.io> wrote:



On Wednesday, March 31, 2021, 05:30:24 AM MDT, D C *Mac* Macdonald <k2gkk@hotmail.com> wrote:


your expensive radio to become the ground path
Possible only if you connect your radio negative lead to the battery negative terminal, which is bad installation practice. Which I guess is one reason to keep the fuse, to protect people from themselves...


Mark K5LXP
Albuquerque, NM





Re: low power out on HF

Mark Brueggemann
 

On Wednesday, March 31, 2021, 05:30:24 AM MDT, D C *Mac* Macdonald <k2gkk@hotmail.com> wrote:


  your expensive radio to become the ground path 
Possible only if you connect your radio negative lead to the battery negative terminal, which is bad installation practice.  Which I guess is one reason to keep the fuse, to protect people from themselves...


Mark K5LXP
Albuquerque, NM


Re: low power out on HF

Mister Mike
 

Not so fast! It is prudent to fuse both sides of the power cord. Just make sure the contact points are clean. Use a Dremel wire brush and then apply some DeOxit to retard future oxidation.

73,

Michael, W1RC

On Mar 31, 2021, at 3:16 AM, Helmut Wabnig <hwabnig@aon.at> wrote:

On Tue, 30 Mar 2021 14:34:17 -0500, you wrote:

I have personally experienced this, after discovering 30 watts output on hf
on a used rig
I bought. I was not happy, but amazed to discover warmth around the fuse
holders and
adjacent power cable. I measured around 1.4 or more volts drop at radio
thanks to this
oxidation that I discovered on the fuse blades. I cleaned them back to
shiny state, and
problem was resolved for only a while...so I soldered the fuses inside the
fuse cases and no
problems since- full power out, no more excessive voltage drop (the IC 7000
requires
near full voltage for expected power out).

I was amazed. The two lines of oxidation were very visible on the fuse
blades before
buffing them out.

73,

Steve W5ZA

Usually only one fuse is sufficient, remove the ground wire fuse.


w





Re: low power out on HF

D C *Mac* Macdonald
 

Do NOT, repeat, do NOT remove the ground leg fuse
in a mobile installation.  A lost vehicle ground can
cause attempting to start the vehicle to use your
expensive radio to become the ground path according
to many sources.  That is why the factory lead has
that fuse.
 
73 - Mac, K2GKK/5
Since 30 Nov 1953
Oklahoma City, OK
USAF (Retired) 61-81
FAA (Retired) 94-10
 


From: ic7000@groups.io <ic7000@groups.io> on behalf of Helmut Wabnig <hwabnig@...>
Sent: Wednesday, March 31, 2021 02:16
To: ic7000@groups.io <ic7000@groups.io>
Subject: Re: [ic7000] low power out on HF
 
On Tue, 30 Mar 2021 14:34:17 -0500, you wrote:

>I have personally experienced this, after discovering 30 watts output on hf
>on a used rig
>I bought.  I was not happy, but amazed to discover warmth around the fuse
>holders and
>adjacent power cable.  I measured around 1.4 or more volts drop at radio
>thanks to this
>oxidation that I discovered on the fuse blades.  I cleaned them back to
>shiny state, and
>problem was resolved for only a while...so I soldered the fuses inside the
>fuse cases and no
>problems since- full power out, no more excessive voltage drop (the IC 7000
>requires
>near full voltage for expected power out).
>
>I was amazed.  The two lines of oxidation were very visible on the fuse
>blades before
>buffing them out.
>
>73,
>
>Steve    W5ZA
>

Usually only one fuse is sufficient, remove the ground wire fuse.


Re: low power out on HF

Helmut Wabnig
 

On Tue, 30 Mar 2021 14:34:17 -0500, you wrote:

I have personally experienced this, after discovering 30 watts output on hf
on a used rig
I bought. I was not happy, but amazed to discover warmth around the fuse
holders and
adjacent power cable. I measured around 1.4 or more volts drop at radio
thanks to this
oxidation that I discovered on the fuse blades. I cleaned them back to
shiny state, and
problem was resolved for only a while...so I soldered the fuses inside the
fuse cases and no
problems since- full power out, no more excessive voltage drop (the IC 7000
requires
near full voltage for expected power out).

I was amazed. The two lines of oxidation were very visible on the fuse
blades before
buffing them out.

73,

Steve W5ZA

Usually only one fuse is sufficient, remove the ground wire fuse.


w


Re: low power out on HF

wa5itw
 

I have personally experienced this, after discovering 30 watts output on hf on a used rig
I bought.  I was not happy, but amazed to discover warmth around the fuse holders and
adjacent power cable.  I measured around 1.4 or more volts drop at radio thanks to this
oxidation that I discovered on the fuse blades.  I cleaned them back to shiny state, and
problem was resolved for only a while...so I soldered the fuses inside the fuse cases and no
problems since- full power out, no more excessive voltage drop (the IC 7000 requires
near full voltage for expected power out).

I was amazed.  The two lines of oxidation were very visible on the fuse blades before
buffing them out.

73,

Steve    W5ZA

On Tue, Jan 19, 2021 at 10:58 AM Mark Langenfeld <lmlangenfeld@...> wrote:
Very first thing: check the fuses in the DC supply cable for oxidation.  They are notorious for that and, when contaminated, cause a significant voltage drop that can manifest as a loss of TX power out.  This may or may not be your problem, but it is a simple check that could (if the culprit is found there) save you headaches and money.

GL es 73,

Mark -- WA9ETW


Re: when turned on display

Jamie WW3S <ww3s@...>
 

The good thing about these new rigs is everything is menu driven.....




The bad thing about these new rigs is everything is menu driven !!!




On Mar 29, 2021, at 7:34 PM, LeRoy Prosic <lprosic@...> wrote:



Please excuse my ignorance , i figured it out with your help .

Now to enter HF nets and repeaters . 

I,m 78 years old and handy caped .

This is my first menued driven rig .

I replaced a FT767GX Yaesu .

Thank you so much .

keep safe

LeRoy G. Prosic

VE3LGP


---------- Original Message ----------
From: "Bob Hoffmann, K4CQO" <rjhoffmann@...>
Date: March 27, 2021 at 6:27 PM

<image001.png>

 

 

73 – K4CQO

Bob Hoffmann

<image002.png>

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of LeRoy Prosic
Sent: Saturday, March 27, 2021 5:47 PM
To: ic7000@groups.io
Subject: [ic7000] when turned on display

 

Purchased a used IC7000 when it is turned on it displays the previous owners call letters.

How can i delete this and inter my call letters ?   

 


 


 


Re: when turned on display

 

Please excuse my ignorance , i figured it out with your help .

Now to enter HF nets and repeaters . 

I,m 78 years old and handy caped .

This is my first menued driven rig .

I replaced a FT767GX Yaesu .

Thank you so much .

keep safe

LeRoy G. Prosic

VE3LGP


---------- Original Message ----------
From: "Bob Hoffmann, K4CQO" <rjhoffmann@...>
Date: March 27, 2021 at 6:27 PM

 

 

73 – K4CQO

Bob Hoffmann

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of LeRoy Prosic
Sent: Saturday, March 27, 2021 5:47 PM
To: ic7000@groups.io
Subject: [ic7000] when turned on display

 

Purchased a used IC7000 when it is turned on it displays the previous owners call letters.

How can i delete this and inter my call letters ?   

 


 


 


Re: when turned on display

r norris
 

On Mar 27, 2021, at 18:27, Bob Hoffmann, K4CQO <rjhoffmann@...> wrote:

<image001.png>
 
 
73 – K4CQO
Bob Hoffmann
<image002.png>
 
 
From: ic7000@groups.io <ic7000@groups.io> On Behalf Of LeRoy Prosic
Sent: Saturday, March 27, 2021 5:47 PM
To: ic7000@groups.io
Subject: [ic7000] when turned on display
 

Purchased a used IC7000 when it is turned on it displays the previous owners call letters.

How can i delete this and inter my call letters ?   



Re: when turned on display

Bob Hoffmann, K4CQO
 

 

 

73 – K4CQO

Bob Hoffmann

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of LeRoy Prosic
Sent: Saturday, March 27, 2021 5:47 PM
To: ic7000@groups.io
Subject: [ic7000] when turned on display

 

Purchased a used IC7000 when it is turned on it displays the previous owners call letters.

How can i delete this and inter my call letters ?   


when turned on display

 

Purchased a used IC7000 when it is turned on it displays the previous owners call letters.

How can i delete this and inter my call letters ?   

181 - 200 of 41398