Date   

Re: rt system program

David Burt W4OFO
 

On Mar 14, 2022, at 7:18 PM, LeRoy Prosic <lprosic@...> wrote:

First of all i like to thank everyone for responded to my first question with a solution.
Now I am trying to down load my area uhf/vhf frequencies into my ic7000 from the call book which is suppose to be in the RT Program and it is now where to be found .
Has any one had this problem ?
An e-mail was sent to RT and they told me to try again to enter the program into my computer .
Same thing, no call book to drag and drop the frequencies into the 700 ?     


Re: rt system program

 

I think that you can export your local repeaters from RepeaterBook on the web, You will get a file (perhaps CSV) that you can import into RT systems.
It takes a little looking for the correct files etc, but I think it can be done .


rt system program

 

First of all i like to thank everyone for responded to my first question with a solution.
Now I am trying to down load my area uhf/vhf frequencies into my ic7000 from the call book which is suppose to be in the RT Program and it is now where to be found .
Has any one had this problem ?
An e-mail was sent to RT and they told me to try again to enter the program into my computer .
Same thing, no call book to drag and drop the frequencies into the 700 ?     


Re: Icom7000 set up with WSJT-X

 

The IC-7200 and IC-7000 have different addresses for the C-IV.
The default for IC-7000 is 70h or hex address 70 
The default for  IC-7300 is 94h or hex 94
Check the address in your radio to be sure.
Also be sure to match baud rate as well


Re: Icom7000 set up with WSJT-X

Larry Ryan
 

I have done this many times with my IC7000 by following the manual for the Signal Link USB and manual for WSJT-X.  First of all, I purchased the IC-7000/FT-817 jumper module SLMMOD6PM for the Signal Link and installed that first thing. This module sets the correct rig jumpers in the 6-pin mini-DIN Data Port. If you don't have the module, you have to place jumpers properly as shown in the manual. You have to open the Signal Link to access this Port.  Then I simply followed the manuals. I set my power to 50W before operating. I use HRD for logging and find that WSJT-X plays well with HRD. There is a selection for IC-7000 in both. I'm sure setting for an IC-7300 won't work with an IC-7000.  
The relevant manuals are all available on-line.  The instructions to do all this can be found there. I've operated portable with my IC-7000 using PSK then later, FT-8 many many times with this setup. 

73, Larry W7DGP


Icom7000 set up with WSJT-X

Bernie <cltoby@...>
 

Helping a friend over the radio and trying to help him get WSJT-X running with his 7000 and a Signalink interface. Can someone provide me with the instructions to do this. Getting the rig error message at this time. The setting from my 7300 don't appear to work.
Thanks Chuck  K3CLT


Re: rt system program ic7000?

Glenn Jensen
 

It is the CIV jack - I have the same cable / SW.

73's - Glenn


On Thu, Mar 10, 2022 at 3:17 PM David Milligan <1proinv@...> wrote:
If I’m not mistaken it’s the CI-V jack



David P Milligan
843-615-6858


On Mar 10, 2022, at 18:09, LeRoy Prosic <lprosic@...> wrote:

Just received the RT System program and i don,t see any where in the instructions where you plug the the cord into the back of the radio ? 
Can any one help this 78 year old new be ?
VE3LGP


Re: rt system program ic7000?

Paul Levasseur
 


Re: rt system program ic7000?

David Milligan
 

If I’m not mistaken it’s the CI-V jack



David P Milligan
843-615-6858


On Mar 10, 2022, at 18:09, LeRoy Prosic <lprosic@...> wrote:

Just received the RT System program and i don,t see any where in the instructions where you plug the the cord into the back of the radio ? 
Can any one help this 78 year old new be ?
VE3LGP


rt system program ic7000?

 

Just received the RT System program and i don,t see any where in the instructions where you plug the the cord into the back of the radio ? 
Can any one help this 78 year old new be ?
VE3LGP


Low TX Audio

John B. (AD5RN)
 

After an RF feedback event, my IC7000 has very low TX audio. The TX power meter barely moves when speaking into the microphone in SSB mode, and on FM, the deviation is only 1 kHz. The MIC Gain setting in the menu is at maximum. However, in FM, if I enable PL tone, its deviation is correct (~0.7 kHz). I have tried three microphones---no change. Audio fed into the back of the radio for digital modes is also low, requiring me to maximize the AF drive from the PC to get 40W out of the radio in FT8.

I tried replacing IC452, but that did not fix it, and I still have the same problem.

Has anyone seen this before, or are there any suggestions?

Thank you,
John, AD5RN


Re: IC 7000

Mark Schoonover
 

If you can use a power supply 25A continuous or larger. The 7K is sensitive to voltage drops. 

73! Mark KA6WKE

Website: https://www.ka6wke.net

On Sun, Feb 20, 2022, 10:18 Van <wd6fgb@...> wrote:

Clean the fuses in the power cord

--
Sent from Outlook Email App for Android

Sunday, 20 February 2022, 08:45AM -08:00 from giubigaz@...:

Hello everyone

I have a problem with my Ic 7000 this is it, the problem is on the TX part, it usually works regularly but suddenly it happens that the power drops considerably, for example it goes from 50w to about 15 without a logic of time.
Has anyone had this problem, how was it solved?
Thanks in advance to anyone who can give me some useful information to solve this problem.

73 '  Giuliano  IK5UTD


Re: IC 7000

Van
 

Clean the fuses in the power cord

--
Sent from Outlook Email App for Android

Sunday, 20 February 2022, 08:45AM -08:00 from giubigaz@...:

Hello everyone

I have a problem with my Ic 7000 this is it, the problem is on the TX part, it usually works regularly but suddenly it happens that the power drops considerably, for example it goes from 50w to about 15 without a logic of time.
Has anyone had this problem, how was it solved?
Thanks in advance to anyone who can give me some useful information to solve this problem.

73 '  Giuliano  IK5UTD


Re: IC 7000

Pasquale S
 

Hi Giuliano

Do you have this issue in all bands (HF/50/VHF/UHF) or not ? It’s important to know because if this trouble happens in all bands, I suppose that you are a fault in driver mosfet (PD55015).

Let us know about it.

73s Pasquale IW0HEX

 

 

Inviato da Posta per Windows

 

Da: giubigaz@...
Inviato: domenica 20 febbraio 2022 17:45
A: ic7000@groups.io
Oggetto: [ic7000] IC 7000

 

Hello everyone

I have a problem with my Ic 7000 this is it, the problem is on the TX part, it usually works regularly but suddenly it happens that the power drops considerably, for example it goes from 50w to about 15 without a logic of time.

Has anyone had this problem, how was it solved?

Thanks in advance to anyone who can give me some useful information to solve this problem.


73 '  Giuliano  IK5UTD

 


IC 7000

giubigaz@...
 

Hello everyone

I have a problem with my Ic 7000 this is it, the problem is on the TX part, it usually works regularly but suddenly it happens that the power drops considerably, for example it goes from 50w to about 15 without a logic of time.
Has anyone had this problem, how was it solved?
Thanks in advance to anyone who can give me some useful information to solve this problem.

73 '  Giuliano  IK5UTD


Re: CHIRP

Tim Davis KJ4DHF
 

Very true on the chip set troubles. This 1 is FTDI and works great for HRD to connect to radio and control the rig. I already downloaded the software but it is useless without the cable from RT Systems so waiting now for postman.


Re: CHIRP

Joe Krout
 

That's probably best, and Chirp may work for you using the rt cable. 
Some usb/rs232 cables used a cloned chip set that is not compatible with current drivers, and windows hates old drivers. 

Usb cables need to use the ftdi chip set and not the cloned prolific chip set.

Best of luck.
Joe KR0UT 

On Sat, Feb 19, 2022, 6:25 PM Tim Davis KJ4DHF via groups.io <kj4dhf=yahoo.com@groups.io> wrote:
Been thru all of that. Was able to read radio 1 time out of 50 tries. Edited my file to add some stuff an now cannot write back to radio.

Wife spent the 50$ to buy the RT Systems software and cable. Waiting on mail man next week.

Tim


Re: CHIRP

Tim Davis KJ4DHF
 

Been thru all of that. Was able to read radio 1 time out of 50 tries. Edited my file to add some stuff an now cannot write back to radio.

Wife spent the 50$ to buy the RT Systems software and cable. Waiting on mail man next week.

Tim


Re: CHIRP

Joe Krout
 

I haven't tried this but,  (I love advise that starts this way. :) )

Have you tried saving one or two frequencies to the ic-7000 memory and then uploading to Chirp?

It is also possible that you have a baud rate or bit rate mismatch,  or the wrong com port #.  See attached manual page.


Joe KR0UT 




On Sat, Feb 19, 2022, 12:23 PM Tim Davis KJ4DHF via groups.io <kj4dhf=yahoo.com@groups.io> wrote:
Hello All,

Anyone happen to have a IC-7000 file that was done with CHIRP software.

Trying to setup some memory channels in my 7K and CHIRP will not save the empty memory files to my pc so I can edit then upload to radio.


CHIRP

Tim Davis KJ4DHF
 

Hello All,

Anyone happen to have a IC-7000 file that was done with CHIRP software.

Trying to setup some memory channels in my 7K and CHIRP will not save the empty memory files to my pc so I can edit then upload to radio.

221 - 240 of 41757