Date   

Re: Intermitten tx

Linda C
 

Steve W3AHL,
I’ve been following this thread because I’ve had the same problem with a used IC7000 I bought several years ago. I bought a replacement mic (off of eBay, which was probably stupid) just to find it had the exact same issue. I think now that maybe it was one of the original faulty ones that Icom pulled. Who knows.

I’m looking forward to trying the fix you’re talking about as soon as I can replace the antennas a tornado got.

Thanks for the info and thanks to all for the thread

73,
Linda AG5HJ

On Jun 26, 2021, at 9:48 AM, Steve W3AHL <w3ahl@att.net> wrote:

SKQJLAA010


Re: Intermitten tx

Mike
 

I tried back mic jack....very weird...works better but only if I turn vox on... I am really confused by the issue and if it is hardware of software related, I didn't have time to torture shoot too much I will tonight. If vox is off it seems to not be in tx although now I get the led on the mic.... 


On Sat, Jun 26, 2021, 10:48 AM Steve W3AHL <w3ahl@...> wrote:
The original PTT switch used in the HM-151 mic'swas not sealed and had a cheap actuator design.  Icom started shipping a better sealed switch for repair parts in 2007 I think.  It was an ALPS SKQJLBA010, available from Mouser.com, although it is currently backordered, but they have SKQJLAA010 in stock, which is identical except with a black instead of gray actuator stem.

https://www.mouser.com/ProductDetail/Alps-Alpine/SKQJLAA010?qs=%2Fha2pyFaduiNCIVDxt%252BQU%2F5bP%252BmBGtzmFC3u3iEdhgc%3D

The switch is easy to replace, however it is important to observe the manufacturer's soldering instructions, available in the datasheet on Mouser's web site at the link above.  It specifies a maximum soldering iron tip temperature of 350 degrees C, using no more than a 20 watt iron applied for a maximum of 3 seconds to each lead.  Exceeding these limits can cause the aluminum snap disk inside the switch to oxidize and cause premature failure or intermittent operation.

Since the old switch is not sealed it can often be "repaired" temporarily by squirting a good quality contact cleaner such as Deoxit 5 into the switch and repeatedly pushing the plunger to help clean the oxidation.  However, the switch should be replaced soon after it is cleaned.  The new switches are sealed and cannot be cleaned.

Steve, W3AHL


Re: Intermitten tx

Steve W3AHL
 

The original PTT switch used in the HM-151 mic'swas not sealed and had a cheap actuator design.  Icom started shipping a better sealed switch for repair parts in 2007 I think.  It was an ALPS SKQJLBA010, available from Mouser.com, although it is currently backordered, but they have SKQJLAA010 in stock, which is identical except with a black instead of gray actuator stem.

https://www.mouser.com/ProductDetail/Alps-Alpine/SKQJLAA010?qs=%2Fha2pyFaduiNCIVDxt%252BQU%2F5bP%252BmBGtzmFC3u3iEdhgc%3D

The switch is easy to replace, however it is important to observe the manufacturer's soldering instructions, available in the datasheet on Mouser's web site at the link above.  It specifies a maximum soldering iron tip temperature of 350 degrees C, using no more than a 20 watt iron applied for a maximum of 3 seconds to each lead.  Exceeding these limits can cause the aluminum snap disk inside the switch to oxidize and cause premature failure or intermittent operation.

Since the old switch is not sealed it can often be "repaired" temporarily by squirting a good quality contact cleaner such as Deoxit 5 into the switch and repeatedly pushing the plunger to help clean the oxidation.  However, the switch should be replaced soon after it is cleaned.  The new switches are sealed and cannot be cleaned.

Steve, W3AHL


Re: Intermitten tx

James KB7TBT
 

Very common issue is the momentary switch inside the mic fails..

If you open the mic and press the button hard it should TX.

Lots of folks that do the mic mod replace the switch as well..

(I have the OEM mic that has failed in a box)

73

James - KB7TBT

On 6/25/21 6:57 PM, mforsythe@gmail.com wrote:
Ok, so I thought I had a mic issue, no tx when I press the button, grabbed mic from another icom vhf seemed to work fine a few months. Fast forward now, no tx on any mic. Can tune auto tuner fine, so I know the radio can tx. If you press the mic a million times sometimes it goes into tx. Other times when it does it imminently shuts off. I'm at a loss with this one.


Re: Intermitten tx

Paul Hansen
 

Have you tried both mic jacks?

 

Thank You

 

Paul W. Hansen, W6XA

Amateur Radio Service

2134 Carthage Road

Tucker, GA 30084

(864) 222-3539

www.amateurradioservice.com

 

From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of mforsythe@...
Sent: Friday, June 25, 2021 21:58
To: ic7000@groups.io
Subject: [ic7000] Intermitten tx

 

Ok, so I thought I had a mic issue, no tx when I press the button, grabbed mic from another icom vhf seemed to work fine a few months. Fast forward now, no tx on any mic. Can tune auto tuner fine, so I know the radio can tx. If you press the mic a million times sometimes it goes into tx. Other times when it does it imminently shuts off. I'm at a loss with this one. 


Re: Intermitten tx

Max
 

Have you tried it into a dummy load? That is what I would try first, just to make sure you don't have an RF problem. And the 7000 has two mike jacks, one on the control head and one on the back of the main radio. Try them both.

Max KG4PID


On Friday, June 25, 2021, 09:00:07 PM CDT, mforsythe@... <mforsythe@...> wrote:


Ok, so I thought I had a mic issue, no tx when I press the button, grabbed mic from another icom vhf seemed to work fine a few months. Fast forward now, no tx on any mic. Can tune auto tuner fine, so I know the radio can tx. If you press the mic a million times sometimes it goes into tx. Other times when it does it imminently shuts off. I'm at a loss with this one. 


Intermitten tx

Mike
 

Ok, so I thought I had a mic issue, no tx when I press the button, grabbed mic from another icom vhf seemed to work fine a few months. Fast forward now, no tx on any mic. Can tune auto tuner fine, so I know the radio can tx. If you press the mic a million times sometimes it goes into tx. Other times when it does it imminently shuts off. I'm at a loss with this one. 


Re: Memory scan not working

Craig Pitcher
 

Hi Paul,

 

Thank you so much!  Somehow I had deleted all the asterisks,  Added them back and it now works fine.

 

73,

 

Craig

W6ADV

 

From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of Paul G8NRY
Sent: Friday, June 25, 2021 6:04 AM
To: ic7000@groups.io
Subject: Re: [ic7000] Memory scan not working

 

Have you set the Select flag in the channels you want to scan (use SEL on screen S2, * appears next to Memo number) and before pressing SCN to scan only Selected channels?
For controlling and setting up the 7000 from a PC, I highly recommend the IC7000BKT CAT software, gives you full remote control and the registered version has full memory management and backup too. Http://www.maniaradio.it/en/ic7000bkt.html


Re: Memory scan not working

Paul G8NRY
 

Have you set the Select flag in the channels you want to scan (use SEL on screen S2, * appears next to Memo number) and before pressing SCN to scan only Selected channels?
For controlling and setting up the 7000 from a PC, I highly recommend the IC7000BKT CAT software, gives you full remote control and the registered version has full memory management and backup too. Http://www.maniaradio.it/en/ic7000bkt.html


Re: Alc

Zdravko E77AR
 

Hello Rupert,

Thursday, June 24, 2021, 11:09:25 PM, you wrote:

Hi Group..
My 7000 has developed a problem,no power out on ssb hf and as soon
as mic is keyed alc swings full scale turned down power and mic gain
same problem,rig works okonvhf uhf any ideas cause of problem
Rupert
6y5rw
Same problem but on all bands...



--
Best regards,
Zdravko mailto:e77ar@hamradiors.org


Alc

Rupert Walford
 

Hi Group..
My 7000 has developed a problem,no power out on ssb hf and as soon as mic is keyed alc swings full scale turned down power and mic gain same problem,rig works okonvhf uhf any ideas cause of problem
Rupert
6y5rw


Re: Memory scan not working

Craig Pitcher
 

Hi Glenn,

 

Thanks for your reply.  I have RT software &  cable for my Baofeng HT, and it works great.(cost more than the HT)

 

However, my IC-7000 is all programmed and I just need to resolve why the rig will no longer scan in memory mode.

 

73,

 

Craig

From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of Glenn Jensen
Sent: Wednesday, June 23, 2021 5:09 PM
To: ic7000@groups.io
Subject: Re: [ic7000] Memory scan not working

 

Craig,

If you have a RT-Systems software and their USB cable, you can download your memories, edit, and then upload them back into your rig (without a complete reset).  If you had to reset, at least you would have a backup.

I believe you can also use Chirp (for the same objective), realizing that memory edits within Chirp, on this rig, are ‘live’… so be careful that you don’t barf your other memories.  Using Chirp does require a USB CAT cable, but not one with the embedded RT-Systems ID.  As an aside, you can use the RT cable on Chirp (and with other HAM CAT software).

You may wish to consider organizing your memories by frequency / antenna alignment (6 meters and below in groups, above in other groups).  This will save your relays from clicking between antennas on memory scan.  You could use one of the memory groups for repeaters, if you don’t mind the clicking.

73’s – Glenn

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Craig Pitcher via groups.io
Sent: Wednesday, June 23, 2021 11:37 AM
To: ic7000@groups.io
Subject: [ic7000] Memory scan not working

 

I recently added a new VHF frequency to the memory.  It showed up on the frequency list, but when I went to scan the memory channels, that function was frozen.  I took the entry out and tried again, but no scan.  Scan does work in VFO mode to scan the VHF range.  I don't want to do a master reset and am hoping there is a simple cure.

Anyone know how to resolve this?

Thanks,

Craig
W6ADV


Re: Memory scan not working

Glenn Jensen
 

Craig,

If you have a RT-Systems software and their USB cable, you can download your memories, edit, and then upload them back into your rig (without a complete reset).  If you had to reset, at least you would have a backup.

I believe you can also use Chirp (for the same objective), realizing that memory edits within Chirp, on this rig, are ‘live’… so be careful that you don’t barf your other memories.  Using Chirp does require a USB CAT cable, but not one with the embedded RT-Systems ID.  As an aside, you can use the RT cable on Chirp (and with other HAM CAT software).

You may wish to consider organizing your memories by frequency / antenna alignment (6 meters and below in groups, above in other groups).  This will save your relays from clicking between antennas on memory scan.  You could use one of the memory groups for repeaters, if you don’t mind the clicking.

73’s – Glenn

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Craig Pitcher via groups.io
Sent: Wednesday, June 23, 2021 11:37 AM
To: ic7000@groups.io
Subject: [ic7000] Memory scan not working

 

I recently added a new VHF frequency to the memory.  It showed up on the frequency list, but when I went to scan the memory channels, that function was frozen.  I took the entry out and tried again, but no scan.  Scan does work in VFO mode to scan the VHF range.  I don't want to do a master reset and am hoping there is a simple cure.

Anyone know how to resolve this?

Thanks,

Craig
W6ADV


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Glenn Jensen
 

Outstanding…. Enjoy (great radio and software).

73’s – Glenn

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Wednesday, June 23, 2021 1:39 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Glenn,

 

Thanks for the help. All working now; may have been related to baud rate harmony.

 

73

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 9:22 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Kurt,

My USB port happens to be 22 (using a RTS cable).

That error is generally associated with not picking the correct USB port (at least for me).  Could you have another program running that conflicts with Flrig (i.e. running WSJTX at the same time you trying to run Flrig, or Log4OM with frequency updates?).

This is a dedicated port, for one function - CAT control.  Specialty software may allow you to share the port- i.e. virtualizing it, then sharing it.

Let me know - if it works with HRD, you are close (use the same USB port number as HRD, and make sure HRD is completely closed).

73's - Glenn

 

 

 

On 6/22/21 7:39 PM, Kurt Sweeny wrote:

 

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 6:36 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Thanks Glenn

 

 

I am not running FLDIGI. When FLRIG is configured as you describe I get this message:

 

 

 

 

 

I am wondering if there is something that needs to be configured on the Comm port?

 

Kurt

 

----------------------------------------------------------------------

 

Hi Kurt,



Here is mine, under Windows 10 – I use it with Fldigi, works great.

73’s – Glenn WA6BJQ

 



 

 

 

 

Fldigi

 

 

CW keying…. (you will have to properly set your keyer config on the rig)

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Tuesday, June 22, 2021 1:51 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Kurt Sweeny
 

Glenn,

 

Thanks for the help. All working now; may have been related to baud rate harmony.

 

73

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 9:22 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Kurt,

My USB port happens to be 22 (using a RTS cable).

That error is generally associated with not picking the correct USB port (at least for me).  Could you have another program running that conflicts with Flrig (i.e. running WSJTX at the same time you trying to run Flrig, or Log4OM with frequency updates?).

This is a dedicated port, for one function - CAT control.  Specialty software may allow you to share the port- i.e. virtualizing it, then sharing it.

Let me know - if it works with HRD, you are close (use the same USB port number as HRD, and make sure HRD is completely closed).

73's - Glenn

 

 

 

On 6/22/21 7:39 PM, Kurt Sweeny wrote:

 

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 6:36 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Thanks Glenn

 

 

I am not running FLDIGI. When FLRIG is configured as you describe I get this message:

 

 

 

 

 

I am wondering if there is something that needs to be configured on the Comm port?

 

Kurt

 

----------------------------------------------------------------------

 

Hi Kurt,



Here is mine, under Windows 10 – I use it with Fldigi, works great.

73’s – Glenn WA6BJQ

 



 

 

 

 

Fldigi

 

 

CW keying…. (you will have to properly set your keyer config on the rig)

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Tuesday, June 22, 2021 1:51 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS


Memory scan not working

Craig Pitcher
 

I recently added a new VHF frequency to the memory.  It showed up on the frequency list, but when I went to scan the memory channels, that function was frozen.  I took the entry out and tried again, but no scan.  Scan does work in VFO mode to scan the VHF range.  I don't want to do a master reset and am hoping there is a simple cure.

Anyone know how to resolve this?

Thanks,

Craig
W6ADV


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Glenn Jensen
 

Kurt,

My USB port happens to be 22 (using a RTS cable).

That error is generally associated with not picking the correct USB port (at least for me).  Could you have another program running that conflicts with Flrig (i.e. running WSJTX at the same time you trying to run Flrig, or Log4OM with frequency updates?).

This is a dedicated port, for one function - CAT control.  Specialty software may allow you to share the port- i.e. virtualizing it, then sharing it.

Let me know - if it works with HRD, you are close (use the same USB port number as HRD, and make sure HRD is completely closed).

73's - Glenn





On 6/22/21 7:39 PM, Kurt Sweeny wrote:

 

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 6:36 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Thanks Glenn

 

 

I am not running FLDIGI. When FLRIG is configured as you describe I get this message:

 

 

 

 

 

I am wondering if there is something that needs to be configured on the Comm port?

 

Kurt

 

----------------------------------------------------------------------

 

Hi Kurt,



Here is mine, under Windows 10 – I use it with Fldigi, works great.

73’s – Glenn WA6BJQ

 



 

 

 

 

Fldigi

 

 

CW keying…. (you will have to properly set your keyer config on the rig)

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Tuesday, June 22, 2021 1:51 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Kurt Sweeny
 

 

 

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Glenn Jensen
Sent: Tuesday, June 22, 2021 6:36 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Thanks Glenn

 

 

I am not running FLDIGI. When FLRIG is configured as you describe I get this message:

 

 

 

 

 

I am wondering if there is something that needs to be configured on the Comm port?

 

Kurt

 

----------------------------------------------------------------------

 

Hi Kurt,



Here is mine, under Windows 10 – I use it with Fldigi, works great.

73’s – Glenn WA6BJQ

 



 

 

 

 

Fldigi

 

 

CW keying…. (you will have to properly set your keyer config on the rig)

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Tuesday, June 22, 2021 1:51 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Glenn Jensen
 

Hi Kurt,

Here is mine, under Windows 10 – I use it with Fldigi, works great.

73’s – Glenn WA6BJQ

 



 

 

 

 

Fldigi

 

 

CW keying…. (you will have to properly set your keyer config on the rig)

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Kurt Sweeny
Sent: Tuesday, June 22, 2021 1:51 PM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS


Re: OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

Kurt Sweeny
 

Scott,

 

Thanks for your recommendations and in sharing your experience.. I will look into RS-BA1 and a junker intel box to run next to the radio. Dx Engineering was not encouraging about  RS_BA1 for the IC-7000 and the Intel literature has a few caveats in terms of reduced capabilities but still probably the best option.

 

As an aside, I thought I would see if I could connect FLRIG with 7000 but had no luck; played with baud rates Comm  port designations, etc., no luck. As a diagnostic step, I was able to instantly connect with an old version of HR Deluxe, so the cable is working and HR Deluxe likes the comm settings. Any favorite items to double check on the FLRIG configuration?

 

Best

 

Kurt KD6LZV

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Scott Honaker
Sent: Sunday, June 20, 2021 10:57 AM
To: ic7000@groups.io
Subject: Re: [ic7000] OPC 1443 Radio to Head Cable -Replacement by an Internet Connection ?

 

I would not say dealing with the video is a show stopper but is added complexity and cost over the efforts I've seen with the IC-7100 (which is just data and audio in/out).  In the IC-7100, the data is serial data but not CI-V and the solutions generally pass the data without trying to interpret it (specifics are available at that link).  The real issue I see is that the IC-7100 is a simpler platform to get working and I have seen a number of efforts to virtualize that head cable.  I would say only the RemoteRig solution has been entirely successful and complete.  Adding video to the list of issues to solve (not addressed by RemoteRig) makes it quite a hurdle.

There are a number of TRUE (operation over the Internet) remote solutions.  You mentioned WFView and there is also Win4IcomSuite https://icom.va2fsq.com/remote-control/.  Both of those are designed for the more modern Icom radios (with USB and network connectivity) and focus on the transport of the real-time spectrum scope that is not an IC-7000 feature.  I mentioned the Icom RS-BA1 software because it specifically supports the IC-7000 and likely offers the best support for all the features of the radio that are available remotely.

When using digital modes remotely, there is another solution.  You can connect the radio to a local machine with whatever software you want to run (FLDigi/FLRig or WSJT-X), then use some kind of remote desktop software (Windows Remote Desktop, TeamViewer, AnyDesk, Chrome Remote Desktop, etc.) to remotely connect to the local PC/radio.  I have used all these solutions and have settled on Chrome Remote Desktop to make a bunch of WSJT contacts on the IC-7100 and IC-7610 in my office while sitting comfortably in front of the TV at home.

Scott N7SS

221 - 240 of 41514