Date   

Re: IC- 7000 USB Driver Software needed

Steve W3AHL
 

Gerard,  If you go to the FTDI link J.D. posted, in the chart showing which drivers are used by operating system version, for Windows 10 there is a link to an installation guide in the right most column.  That guide has info on what to do if the FTDI chip is not automatically detected by Windows (which is normally is).  The instructions are quite detailed, although i haven't tried them, since I haven't had your problem before.

Steve, W3AHL


Re: IC- 7000 USB Driver Software needed

DougH <specialq.que@...>
 

Gerard,

If you are running W10 then the driver should be set up automatically when you attach the USB/Serial adapter. Use device manager - double click Ports(Com & LPT) you should see an entry for your device if driver installed.

Regards,
Doug - GM7SVK


On 08/12/2020 20:07, Gerard Arsenault wrote:
I get it. You are absolutely right. So where can I find a driver for a FT231X USB UART (RS232 to USB converter) adapter that will work on Windows 10 version 2004 ?


Virus-free. www.avg.com


Re: IC- 7000 USB Driver Software needed

 

Some of the counterfeit cables now send a disk with a driver that will replace the FTDI driver and let it work, but this is just confirming that the cable is not genuine FTDI.


Re: IC- 7000 USB Driver Software needed

 

Be aware of one very important thing and that is that a whole lot of the FTDI chips in adapters are counterfeit and this why the WIN 10 will not locate them. 
You might have on of the adapters with the counterfeit chips and this could be the reason that it will not find it.
I have had some that would give a warning and some that would do nothing.
This has been said several times here. 


Re: IC- 7000 USB Driver Software needed

Jerry VE9CD
 

Your question I hope is answered in a couple of replies to other suggestions.


Re: IC- 7000 USB Driver Software needed

Jerry VE9CD
 

This solution requires one to actually see a detected com port before applying the fix. My computer does not recognize the device I am using (FT231X USB UART). I'm continuing my research.


Re: IC- 7000 USB Driver Software needed

 

If you go to device manager and find the FT231X listed under USB COM etc. then go to driver and hit the search for driver on the web.
You can also search for it.
Try looking here:

https://www.ftdichip.com/Drivers/VCP.htm


Re: IC- 7000 USB Driver Software needed

Jerry VE9CD
 

I get it. You are absolutely right. So where can I find a driver for a FT231X USB UART (RS232 to USB converter) adapter that will work on Windows 10 version 2004 ?


Re: IC- 7000 USB Driver Software needed

Don Rolph
 

I had a similar problem when I upgraded to Windows 10.

Microsoft autoinstalled drivers detect whether the USB to serial chip is a true Prolific or FTDI chip or a clone.

If it is a clone, chip the autoinstalled driver will disable the chip.

I found there were two choices:

1) find the old drivers and manually install them and then do not install the windows 10 updated to the FTDI or Prolific chip drivers ( aibt of  pain)

2) throw out all my old clone usb to serial adapters and get new adapters which use standard FTDI or Prolific chips

I chose option 2.

On Tue, Dec 8, 2020 at 8:22 AM Gerard Arsenault <jerrya@...> wrote:
Thank you for your response. I understand that I need a driver. The problem is I cannot find one for the IC-7000.



--

73,
AB1PH
Don Rolph


Re: IC- 7000 USB Driver Software needed

 

There is not a driver for your ic7000! There is a driver for the USB cable you are using to convert to the RS232. The CABLE not the IC7000. The IC7000 has no driver as there is no USB converter in it.


Re: IC- 7000 USB Driver Software needed

Jerry VE9CD
 

Thank you for your response. I understand that I need a driver. The problem is I cannot find one for the IC-7000.


Re: IC- 7000 USB Driver Software needed

Helmut Wabnig
 

On Mon, 07 Dec 2020 12:37:16 -0800, you wrote:

Recently I had a hard drive failure on the computer I use for digital modes on my IC-7000. A newer computer with Windows 10 does not automatically create a com port for the interface that has been working for several years.Can  someone please provide a driver file for the CI-V interface or offer an internet link to one that works?
What does the device manager say?
right click the start button (lower left corner)
and scroll up the list.

OE8UWW


Re: IC- 7000 USB Driver Software needed

DH1KLM
 
Edited

Since the IC7000 does not have a USB interface you should tell us which
interface you are using. If it is a cheap chinese one, it is possible there is a clone FTDI
chip in it which is causing your driver problem.

The following could solve your problem. 
Solve FTDI problem


Re: IC- 7000 USB Driver Software needed

Greg Engle
 

https://www.icomjapan.com/support/firmware_driver/?pg=1&type=&sort1=&old=&class=&genre=&category=

The latest USB should work… 1.30

But the earlier version are there.

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Gerard Arsenault
Sent: Monday, December 07, 2020 12:37 PM
To: ic7000@groups.io
Subject: [ic7000] IC- 7000 USB Driver Software needed

 

Recently I had a hard drive failure on the computer I use for digital modes on my IC-7000. A newer computer with Windows 10 does not automatically create a com port for the interface that has been working for several years.Can  someone please provide a driver file for the CI-V interface or offer an internet link to one that works?


Re: IC- 7000 USB Driver Software needed

 

Download the Windows 10 doesn't like the drivers for many of the Serial converters that do not have the genuine chips used. The drivers from the chip companies now check for having the real thing. 
Look for different drivers and you might have to look in device manager to see what you are dealing with and change the driver/


IC- 7000 USB Driver Software needed

Jerry VE9CD
 

Recently I had a hard drive failure on the computer I use for digital modes on my IC-7000. A newer computer with Windows 10 does not automatically create a com port for the interface that has been working for several years.Can  someone please provide a driver file for the CI-V interface or offer an internet link to one that works?


Re: Temp always showing hot #all

Van
 

The correct position for the SWR/PWR Meter is between the Radio and the Tuner for it to work properly.

73

Van

WD6FGB

 

 

 

From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of Kurt Baeten
Sent: Sunday, December 06, 2020 4:10 AM
To: ic7000@groups.io
Subject: Re: [ic7000] Temp always showing hot #all

 

Hi Carl,
My links are as follows;
Radio -> antenna tuner -> SWR/PWR meter -> Antenna
Nothing else plugged into the tuner.

---
Thanks & 73's de VK6KC
Kurt Baeten


Re: Temp always showing hot #all

 

I think he is saying that the radio shows hot when it is first turned on and not transmitting. You are correct that if it were operated at 100 watts for long on Digital it will be plenty hot.
If the sensors are lying to the CPU then the meter would read high.


Re: Temp always showing hot #all

wb0m
 
Edited

"100W on FT8"

HI Kurt,
I'm not surprised the radio shows "hot" when running a full-duty cycle for 15 seconds at a time. Have you tried cutting back the power of FT8 (maybe 40w) and seeing if the temperature is still high. 
Also:  Does it run how on SSB or other modes?
GL & 73,
Jeff/wb0m


Re: Temp always showing hot #all

AB1DD
 

Try it without the tuner plugged in. Radio direct to the dummy load.
Carl
AB1DD

321 - 340 of 41389