Date   

Re: Video out problem

Geoff
 

Sorry, tried to delete this post as I found the solution. Somehow I succeeded in reposting it. 

.

On 5 Oct 2019, at 12:41, Geoff via Groups.Io <vk3zgw@...> wrote:

On Fri, Oct 4, 2019 at 08:21 PM, Geoff wrote:
I'm after some clues on a video issue.

I have a friend's 7000 that he can not get the video to work on his dash monitor. I connected it to my external monitor which works fine with my 7000, I get a correct image but it's black and white only. Tried swapping between PAL and NTSC xbut no change. The instuction and service manuals are light on information about the video feature.

Any help most welcome.

Thanks
Geoff


Re: IC7K locked up

Charles Scott <cscott@...>
 

Joe:

So far so good. I'm still getting used to some of the differences between the radios, but for the most part the controls make sense.

The cool thing about it is that the control head fits snugly and securely into the pocket (if I can call it that) at the front of the console in my 2014 RAM 1500 without any mounting hardware. I'm still contemplating where to put the control head for my IC-2820 since that was somewhat displaced by the 7100 control head.

On the air it's pretty much flawless. The only thing I find curious is that I put in an external dual-needle watt/swr meter that I calibrated on my bench and found that it doesn't quite track with the SWR indication in the radio. Also checked this with my Bird meter and saw the same thing. I first realized this when I saw that the screwdriver tuner I'm using stopped at a solution that didn't look right on the external meters. That tuner gets SWR data from the radio and when looking at SWR on the radio display it is in fact tuning to a good low SWR. Makes me wonder if there's some kind of reactance in the radio between where it senses reflected power and the antenna connector. The difference can be like 1.5:1 vs 2.5:1. In any case, the radio otherwise seems happy with the tuning solutions. I'll have to take a look at the schematic for the 7100 some time soon.

I do still like the 7000 and will probably keep it and have been using it as another radio on my bench at home tied to a vertical at the back of the yard that has an AH-4 on it. My problem is figuring out how to add switching for some of the VHF/UHF antennas to the 7000 (it's a complicated setup).

So, yes, the 7100 is a pretty good radio. If there is anything I can say I don't like, it's the shape of the control head. While it fits the truck it would be better if it was a flat configuration so I could mount it along with the other radio control head. To set it on a desk they could have provided a plastic angled back to enable that.

Chuck - N8DNX 

On 10/3/2019 5:15 PM, Joe Humet wrote:
Tnx Chuck, I'll take a look at that.
How do you like the 7100??
_


Re: External PTT connection

tunert51@...
 

Hello , I just thought I would add a simular question regarding PTT. If I  were add a different mic and preamp to pins 11 and 2 on the ACC Jack,  can I make a PTT for use through one of the modular jacks? Any info would be much appreciated:) 


73 de VA3GRV. Vince ee


Video out problem

Geoff
 

I'm after some clues on a video issue.

I have a friend's 7000 that he can not get the video to work on his dash monitor. I connected it to my external monitor which works fine with my 7000, I get a correct image but it's black and white only. Tried swapping between PAL and NTSC but no change. The instuction and service manuals are light on information about the video feature.

Any help most welcome.

Thanks
Geoff


Re: IC7K locked up

Joe Humet <k2ds@...>
 

Tnx Chuck, I'll take a look at that.
How do you like the 7100??


Re: IC7K locked up

Charles Scott <cscott@...>
 

Joe:

A long shot, but possible. There's been problems with the Logic Unit that causes a variety of problems. That's the metal-enclosed unit under the back-left of the top cover. I don't have specifics of what Icom thinks the problems are with it, but in my case after using the radio for quite some time it developed intermittent problems controlling various relays.

I pulled it and carefully cleaned the contacts. After doing this twice, the radio settled down when on my bench but still was questionable in my mobile. It's back on my bench now and working fine there and an IC-7100 is in the truck.

Icom service told me that the their solution was to replace the logic unit then (because all of the alignments settings are in the logic board) do a full alignment of the radio. That was more than the radio is worth, so I decided not to.

It's possible that you're having some issue as a result of problems with the Logic Unit or connections to the board below it. It's not hard to take the top off and remove then re-seat that unit to see if there's any change. (With power disconnected of course :)

Chuck - N8DNX

On 10/1/2019 3:41 PM, Joe Humet wrote:
TNX All I will give that a try. I did the reset but that did nothing..


Re: IC7K locked up

Joe Humet <k2ds@...>
 

TNX All I will give that a try. I did the reset but that did nothing..


Re: IC7000 relays

Prabhu
 

Hi,
this is Panasonic made TN relays, the manufacturer code is ATN207, which has 9v coil (now absolute)the close ATN206 and ATN209 available in Aliexpress, sending here the link, check and give your comments, so that it may be useful for others,

Rs. 1,916.58  11%OFF | 10PCS/LOT  relay TN2-5V ATN209 TN2-5V-ATN209 TN25V DC5V 5VDC 5V DIP10
https://s.click.aliexpress.com/e/LiogHAfm

73s

On Monday, 30 September 2019, Ing. Juan Carlos Parra <lu9do@...> wrote:
> Hi guys, I need to replace the IC7000 passband relays P/N 6330001721 . Somebody knows where to get it ? Please send me by mail to lu9do@.... Thanks
> _._,_._,_
> ________________________________
> Groups.io Links:
>
> You receive all messages sent to this group.
>
> View/Reply Online (#40392) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
>
> Your Subscription | Contact Group Owner | Unsubscribe [vu2cck@...]
>
> _._,_._,_


IC7000 relays

Ing. Juan Carlos Parra
 

Hi guys, I need to replace the IC7000 passband relays P/N 6330001721 . Somebody knows where to get it ? Please send me by mail to lu9do@.... Thanks


Re: IC7K locked up

ZL2AAA
 

Check that the lock is not ON just below the tuning knob to the left.
73 Morrie

On 28-Sep-19 2:45 AM, Joe Humet wrote:
I went to turn on my rig the other day and I am unable to change the Freq. It's locked.
I have been through the manual and can't find anything on it. Any ideas before I pack it up and send it out?

Tnx Joe
K2DS


Virus-free. www.avast.com


Re: IC7K locked up

Paul Hansen
 

Reset it. If you still have the problem it might be a defective encoder.

 

Thank you,

 

Paul W. Hansen, W6XA

Amateur Radio Service

2134 Carthage Road

Tucker, GA 30084

(864) 222-3539 office

www.amateurradioservice.com

 

 

From: ic7000@groups.io [mailto:ic7000@groups.io] On Behalf Of Joe Humet
Sent: September 27, 2019 10:46
To: ic7000@groups.io
Subject: [ic7000] IC7K locked up

 

I went to turn on my rig the other day and I am unable to change the Freq. It's locked.
I have been through the manual and can't find anything on it. Any ideas before I pack it up and send it out?

Tnx Joe
K2DS


Re: IC7K locked up

N3EA
 

Make sure you're not in some menu item where the frequency knob does other things. For example, if you have the QS menu set up to the power output setting you won't be able to change frequencies since the big knob is used to adjust power while in that menu. So, be sure you don't have the rig in something like that.
73,

Al, N3EA 


IC7K locked up

Joe Humet <k2ds@...>
 

I went to turn on my rig the other day and I am unable to change the Freq. It's locked.
I have been through the manual and can't find anything on it. Any ideas before I pack it up and send it out?

Tnx Joe
K2DS


Re: External PTT connection

Joe Krout
 

Bob

I believe your issue is that Hsend and Vsend are on different pins on the 13 pin connector.  Hsend is on pin 3, Vsend is on pin 7.  They are two different transistor FET? Switches.

Makes sense, as they are used for amplifier switching, and there are 2 different PA outputs.

73
Joe
KR0UT 

On Thu, Sep 26, 2019, 7:57 AM Bob Hoffmann, K4CQO <rjhoffmann@...> wrote:
I am trying to connect a QRM noise canceler to the unit (using a QRM-180) and I am having trouble getting the PTT relay to switch the noise canceler out of the circuit.

I purchased a cable that is connected to the ACC connection (13 pin plug) with an RCA jack on the other end with a built in relay. However, this is what I am seeing: on VHF the relay is not operated; on HF the relay is operated. This is the case if I transmit or receive -- it does not change the relay setting.

It appears to be set to control using an external amp for HF instead of for VHF -- but I am confused why it does not change when I transmit. Is there a setting that I have to use -- or did I get the wrong cable (the cable is supposed to be good for the ic-7000), or maybe the incorrect way of connecting the ic-7000 to the noise canceler?

The noise canceler uses a ground connection to switch it from receive mode to out of the antenna path when transmitting.


Re: IC-7000 VFO Stability

Robert Hanson
 

Works great
I have hundreds of contacts, DXCC (not all confirmed yet), and WAS, on the 7000
I like having the temp indicator.
I did do a fan mod to better couple the sensor to the heatsink.


Re: External PTT connection

Bob Hoffmann, K4CQO
 

Finally got it to work!

I saw in the manual that there was a 16 pin connector that was provided with the ic-7000 and wanted to look to see if I could use it to replace the one that I had in case the wrong pin was found to be used.

Well, the connector had a cable and an RCA plug on the end. So, I decided to try it. Plugged it into the ic-7000 and the RCA plug into the QRM-180 noise canceler. When I turned the units on, I could switch the band and the relay did not change – still in the receive mode. Then I keyed the transmit, and the QRM-180 switched to transmit mode and then back again to receive mode when the ic-7000 was back to receive mode. Exactly like it should work.

I noticed when looking at the manual that there was a user change to power pin 5 of the connector. I think that what was done and the cable (the one that I purchased from eBay that even has “7k” written on the connector) looks at pin 5 instead of pin 3. So the cable I got was an incorrect cable.

All is good and it is working to switch the QRM-180 to a bypass mode when the ic-7000 is transmitting. Now I just need to get the receive antenna connected and I can see how it works.

Thanks everybody for responding.

 

 

 

73 – K4CQO

Bob Hoffmann

 

 

From: ic7000@groups.io <ic7000@groups.io> On Behalf Of Rich Seifert
Sent: Thursday, September 26, 2019 3:45 PM
To: ic7000@groups.io
Subject: Re: [ic7000] External PTT connection

 

 



On Sep 26, 2019, at 11:47 AM, Bob Hoffmann, K4CQO <rjhoffmann@...> wrote:

 

Thanks for responding Rich.

However, what I am seeing is -- if on 2m & 70cm receive, the relay -- presumable from having voltage applied -- shows not connected. This is whether I am transmitting or not.

For any HF setting (including 6m), it shows that the relay is connected -- presumable by the voltage disconnected from the relay. Again this is whether I am transmitting or not. So the relay is on / off depending on what band the ic-7000 is set to.

Assuming that the hsend is connected to the relay -- that would mean that hsend is grounded whenever an HF band is selected, and not grounded when 2m or 70cm are selected. I was wandering if that is an operation on a different pin than 3 -- meaning that i have the wrong cable, or if there is something that is set in the ic-7000 that does that. 

It looks like there is no such setting -- only the scope of the vsend / hsend. So, can it be that I have the wrong wired cable -- is there a different pin that does that?


Re: External PTT connection

Rich Seifert
 



On Sep 26, 2019, at 11:47 AM, Bob Hoffmann, K4CQO <rjhoffmann@...> wrote:

Thanks for responding Rich.

However, what I am seeing is -- if on 2m & 70cm receive, the relay -- presumable from having voltage applied -- shows not connected. This is whether I am transmitting or not.

For any HF setting (including 6m), it shows that the relay is connected -- presumable by the voltage disconnected from the relay. Again this is whether I am transmitting or not. So the relay is on / off depending on what band the ic-7000 is set to.

Assuming that the hsend is connected to the relay -- that would mean that hsend is grounded whenever an HF band is selected, and not grounded when 2m or 70cm are selected. I was wandering if that is an operation on a different pin than 3 -- meaning that i have the wrong cable, or if there is something that is set in the ic-7000 that does that. 

It looks like there is no such setting -- only the scope of the vsend / hsend. So, can it be that I have the wrong wired cable -- is there a different pin that does that?
_._,_._,_

It sounds like what you want is the INVERSE of the HSEND/VSEND function. Those pins are used by an external device (e.g., a computer interface) to enable transmit on the IC-7000, either HF or VHF/UHF. From what you are saying, you want a signal that goes high (to energize a relay) when the radio is transmitting, e.g., when the manual PTT is pressed or a CW signal enables break-in. I don’t think such a signal is available (at least not easily).

Rich KE1B



Re: External PTT connection

Bob Hoffmann, K4CQO
 

Thanks for responding Rich.

However, what I am seeing is -- if on 2m & 70cm receive, the relay -- presumable from having voltage applied -- shows not connected. This is whether I am transmitting or not.

For any HF setting (including 6m), it shows that the relay is connected -- presumable by the voltage disconnected from the relay. Again this is whether I am transmitting or not. So the relay is on / off depending on what band the ic-7000 is set to.

Assuming that the hsend is connected to the relay -- that would mean that hsend is grounded whenever an HF band is selected, and not grounded when 2m or 70cm are selected. I was wandering if that is an operation on a different pin than 3 -- meaning that i have the wrong cable, or if there is something that is set in the ic-7000 that does that. 

It looks like there is no such setting -- only the scope of the vsend / hsend. So, can it be that I have the wrong wired cable -- is there a different pin that does that?


Re: External PTT connection

Rich Seifert
 

On Sep 26, 2019, at 5:57 AM, Bob Hoffmann, K4CQO <rjhoffmann@outlook.com> wrote:

I am trying to connect a QRM noise canceler to the unit (using a QRM-180) and I am having trouble getting the PTT relay to switch the noise canceler out of the circuit.

I purchased a cable that is connected to the ACC connection (13 pin plug) with an RCA jack on the other end with a built in relay. However, this is what I am seeing: on VHF the relay is not operated; on HF the relay is operated. This is the case if I transmit or receive -- it does not change the relay setting.

It appears to be set to control using an external amp for HF instead of for VHF -- but I am confused why it does not change when I transmit. Is there a setting that I have to use -- or did I get the wrong cable (the cable is supposed to be good for the ic-7000), or maybe the incorrect way of connecting the ic-7000 to the noise canceler?

The noise canceler uses a ground connection to switch it from receive mode to out of the antenna path when transmitting.
If you look at page 12 of the IC-7000 manual, you will see that there are TWO pins for PTT:

—Pin 3 (HSEND) is normally used for PTT on HF/50 MHz. Pulling this pin low will enable transmit on HF/50 MHz. It will not enable transmit on VHF/UHF.

—Pin 7 (VSEND) is normally used for PTT on VHF/UHF. It works exactly the same as pin 3, but for 144/430 MHz only.

This arrangement actually makes sense. In most applications (particularly mobile), you will use a different antenna for HF/50 MHz than for UHF/VHF. Additionally, the output drivers in the IC-7000 are separate for HF/50 MHz and UHF/VHF.

Now, you can change this behavior in the “Set” menu. What is shown above is the default. Look at page 131 of the manual, and you will see that, under the “Set” menu, you can change the parameter “VSEND Select” to “Off.” In this configuration the HSEND pin on the ACC jack will enable transmit (PTT) on ALL bands. This may be what you want.

Rich KE1B


External PTT connection

Bob Hoffmann, K4CQO
 

I am trying to connect a QRM noise canceler to the unit (using a QRM-180) and I am having trouble getting the PTT relay to switch the noise canceler out of the circuit.

I purchased a cable that is connected to the ACC connection (13 pin plug) with an RCA jack on the other end with a built in relay. However, this is what I am seeing: on VHF the relay is not operated; on HF the relay is operated. This is the case if I transmit or receive -- it does not change the relay setting.

It appears to be set to control using an external amp for HF instead of for VHF -- but I am confused why it does not change when I transmit. Is there a setting that I have to use -- or did I get the wrong cable (the cable is supposed to be good for the ic-7000), or maybe the incorrect way of connecting the ic-7000 to the noise canceler?

The noise canceler uses a ground connection to switch it from receive mode to out of the antenna path when transmitting.

861 - 880 of 41258