Date   

Connecting digital mode interface to acc port

MARCO EVANGELISTA
 

I want to do true RTTY connecting my digital modes interface to the ACC port of my IC7000.
The FSK output ot the interface is open collector. May I connect this FSK output directly to pin 10 of the ACC port?
Or do I need to add a pull up resistor?

And for CW, given that the CW of the interface is open collector, may I connect it directly to the KEY port of the 7K?

I would appreciate any help much.

73 Marco, IU8HXM


Bluetooth audio sender/receiver

Ahmad Eddie Mobasheri
 

I have found this:
I think this will send the audio to a bluetooth speaker.
Eddie
ZL1AEM
***********************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM


Re: Bluetooth interface

Andy G7OFC
 

Hi Eddie,

I looked into this about 18 months ago.  My search led to to purchase a couple of BT modules from Amazon.  The problem with with both of them was that one had  a Tx/Rx switch depending on whether you wanted to play your phone to your AV system or connect WiFi headphones to them, and the other, which looked more promising but wasn't, auto sensed whether you had the jack plugged in to the Tx or Rx connector.

No doubt you could build some "glue logic" around the auto sensing one to carry out the switching but it just seemed like too much trouble so I sent them back.

What I did find was the KC-6112 BT Audio Gateway by KC Wirefree.  KC Wirefree have published a reference circuit on their website and a variation of this was implemented by KG4JJH which was published in the August 2013 edition of QST.

Since then there is also a BT unit using the KC-6112 published on instructables.com.

GL

Andy G7OFC


Re: Bluetooth interface

Ludovic Ludo
 

Only for the CAT, not the audio, of course.

Le 18/03/2019 à 06:58, Ludovic Ludo a écrit :
I found it on eBay.
http://radioamateur.forumsactifs.com/t1694-ic7000-interface-bluetooth-de-telecommande
It works with HRD and Chirp.

keywords : bluetooth ic7000
(Less than 14 €)


Re: Bluetooth interface

Ludovic Ludo
 

I found it on eBay.
http://radioamateur.forumsactifs.com/t1694-ic7000-interface-bluetooth-de-telecommande
It works with HRD and Chirp.

keywords : bluetooth ic7000
(Less than 14 €)

Best regards,
Ludovic - F5PBG.


Re: Bluetooth interface

 

I suspected that was the case that the Repeater Book app would not work with "clone" BT adapters.
The BlueCat will do all of the CAT -IV work as well.


Re: Bluetooth interface

Linda C
 

This is a fascinating idea! I’d be interested as well.
Linda


Re: Bluetooth interface

do1cal@...
 

Hello, I have this Bluetooth Interface also. This Interface is only to use with CI-V Signal, not for audio. I wanted to use this Interface at my Car with the Handy App “Repeaterbook” but this App has a Mac-Adress Filter and will only work with the Original-BT-Interface from the builder of the App.
 
This Interface can also use with an BT-Interface on a PC / Laptop, to read/write the memory of the IC-7000. But this Interface is not very useful. I can not recommend to buy this interface. The Money for this can you save for any things.
 
73 de DO1CAL, André
 

From: jsternmd
Sent: Sunday, March 17, 2019 3:41 PM
Subject: Re: [ic7000] Bluetooth interface
 

That doesn’t look like the rear of an IC-7000 (at least not mine).  What are the input/outputs?  - just audio?  There are laterncy problems with older bluetooth’s.

 

73 Jerry NY2KW


Re: Bluetooth interface

jsternmd
 

That doesn’t look like the rear of an IC-7000 (at least not mine).  What are the input/outputs?  - just audio?  There are laterncy problems with older bluetooth’s.

 

73 Jerry NY2KW


Re: Bluetooth interface

JOHN HOSKING <n0moe@...>
 

Try aliexpress.com for the same thing at less than half of the cost. Free shipping and no tax.
John



Sent from my Galaxy Tab® A

-------- Original message --------
From: Mystic Treg <MysticTreg@...>
Date: 3/17/19 5:57 AM (GMT-07:00)
To: ic7000@groups.io
Subject: Re: [ic7000] Bluetooth interface

Interesting, so I looked up bluetooth microphone headphones interface.

https://www.amazon.com/slp/bluetooth-headset-adapter/nwjbygeq8ehq8ks  

J Tregre,
KD8M,
on behalf of
Her Imperial Majesty,
Mystic, Kitty


On Sat, Mar 16, 2019 at 10:26 PM Phillip Potter <p.potter@...> wrote:

Hi Eddie,

No, I haven't done this, but I am quite interested, especially if it means that I can use a wireless headset with my rig!

Phil

On 3/16/2019 5:56 PM, Ahmad Eddie Mobasheri wrote:
Hi all,
I am buying a "Bluetooth interface" for my Ic-7000.
Anyone had experience using this? and what software/s you recommend using Windows 10?  
Photos attached.
Kindly regards
ZL1AEM

***********************
A. Eddie Mobasheri
46 Bollard Avenue
New Windsor 0600
Auckland, NZ
Ph: +64 0212 (Persia) 737 742
**************************************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM


Re: Bluetooth interface

 

I am also very interested in this bluetooth adapter and if it will work with the BlueCat Repeater Book.
It seems that it will work with the CAT-IV to select the frequency and perhaps work the PTT.


Re: Bluetooth interface

Mystic Treg
 

Interesting, so I looked up bluetooth microphone headphones interface.

https://www.amazon.com/slp/bluetooth-headset-adapter/nwjbygeq8ehq8ks  

J Tregre,
KD8M,
on behalf of
Her Imperial Majesty,
Mystic, Kitty


On Sat, Mar 16, 2019 at 10:26 PM Phillip Potter <p.potter@...> wrote:

Hi Eddie,

No, I haven't done this, but I am quite interested, especially if it means that I can use a wireless headset with my rig!

Phil

On 3/16/2019 5:56 PM, Ahmad Eddie Mobasheri wrote:
Hi all,
I am buying a "Bluetooth interface" for my Ic-7000.
Anyone had experience using this? and what software/s you recommend using Windows 10?  
Photos attached.
Kindly regards
ZL1AEM

***********************
A. Eddie Mobasheri
46 Bollard Avenue
New Windsor 0600
Auckland, NZ
Ph: +64 0212 (Persia) 737 742
**************************************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM


Re: Bluetooth interface

Phillip Potter
 

Hi Eddie,

No, I haven't done this, but I am quite interested, especially if it means that I can use a wireless headset with my rig!

Phil

On 3/16/2019 5:56 PM, Ahmad Eddie Mobasheri wrote:
Hi all,
I am buying a "Bluetooth interface" for my Ic-7000.
Anyone had experience using this? and what software/s you recommend using Windows 10?  
Photos attached.
Kindly regards
ZL1AEM

***********************
A. Eddie Mobasheri
46 Bollard Avenue
New Windsor 0600
Auckland, NZ
Ph: +64 0212 (Persia) 737 742
**************************************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM


Bluetooth interface

Ahmad Eddie Mobasheri
 

Hi all,
I am buying a "Bluetooth interface" for my Ic-7000.
Anyone had experience using this? and what software/s you recommend using Windows 10?  
Photos attached.
Kindly regards
ZL1AEM

***********************
A. Eddie Mobasheri
46 Bollard Avenue
New Windsor 0600
Auckland, NZ
Ph: +64 0212 (Persia) 737 742
**************************************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM


Re: Cant change or enter Final Idle Cur(430Mhz) in service menu

Ian Benjamin VE9HB
 

Hi Spiros
The loss of driver idle current occurred while I was going through the service menu setup. It was just over 2A, so I decided to bump it up to 2.5A. First you have to dial the current back to zero to measure the baseline current, and then dial it back up to add 2.5A to the baseline. At that point the process setup process hung, with the current intentionally dialed back to zero.
I hope its just a software glitch, and not failure of the driver. As far as I know, the UHF was working.
--
Ian VE9HB


Re: Cant change or enter Final Idle Cur(430Mhz) in service menu

sv1dpp
 

Hi Ian,
the most likely cause is that the RD60HUF1 is in slow death situation or its damaged and you have to change it.
73 Spiros, SV1DPP


Cant change or enter Final Idle Cur(430Mhz) in service menu

Ian Benjamin VE9HB
 

Hi everyone, first post in this group.
I am working on an IC7000, have the original problem pretty well fixed, but managed to create a problem for myself.
I went through the TX adjustment menu and did all the preceding Idle Current setups just fine.
The last item in the DRIVE/FINAL IDLING CURRENT,   "430MHz idle current"  was more of a problem.
The current value I found was a bit low, so I decided to set it to the correct value, even though the original problem was in the HF bands.
(I know, I know, if it ain't broke.......)
At first I couldn't get the current to drop to zero. Not sure how I managed to enter the 00 current setting, either by exiting the service menu, or by power cycling the radio. Now, I cant enter a non-zero bias current, or put back the original value.. Have tried all kinds of control, menu sequences, no luck.
Has anybody encountered or fixed this glitch?

BTW, original problem was low HF power on 20m band. Turned out the 20m band drew more current than the others, and tripped the overcurrent protection which was set too low. Drawing 20.5A @ 100W out.
--
Thanks
Ian VE9HB


Re: Microphone

Joe
 

I think this question might originate from CB radio days where the mike had to be plugged in for the radio to work? I seem to remember some AM CB sets that required the mike to be plugged in because the PTT switch not only keyed the radio but did some fancy switching of the audio circuit. The same circuit was used for the receive loudspeaker and the transmit AM modulation.

Anyone else remember those days? Or am I having yet another day of cranium flatulence?

73, Joe, k1ike


Re: Microphone

 

As far as I can tell from the schematics there is no problem with the mike in either position on no mike at all.
That would apply to receive or transmit as there are digital communications modes that do not require the mike for operation


Re: Microphone

Mystic Treg
 

Yes


On Wed, Mar 13, 2019, 21:02 Ahmad Eddie Mobasheri <aemobasheri@...> wrote:
Hi all,
My question: is it OK detach the mic from the front , and while connected by the separation cable to the unit, be on receive mode?
Thanks

***********************
A. Eddie Mobasheri
46 Bollard Avenue
New Windsor 0600
Auckland, NZ
Ph: +64 0212 (Persia) 737 742
**************************************

--
Eddie Mobasheri
Auckland, New Zealand
ZL1AEM

1061 - 1080 of 41235