Date   

FW: [IC-7000] Re: Accessory DIN Socket

Kenneth Dyer
 

 

Hope this helps its an ICOM stock OPC-599 Adaptor Cable 13-Pin, ACC connector to 7 Pin + 8 Pin ACC Connector.

I have used it on my ICOM 7000

 

73

Ken GW0RHC/HZ1GW/A92HC

 

 

From: ic7000@... [mailto:ic7000@...]
Sent: 28 January 2018 22:52
To: ic7000@...
Subject: RE: [IC-7000] Re: Accessory DIN Socket

 

 

Icom makes a split pigtail that goes from a 13 pin din to a 7 pin and 6 pin female din.

I believe it may show in your manual on the 7K

 

73

Van

WD6FGB

 

From: ic7000@... [mailto:ic7000@...]
Sent: Sunday, January 28, 2018 2:39 PM
To: ic7000@...
Subject: RE: [IC-7000] Re: Accessory DIN Socket

 

 

Good Evening Brian Et al:

 

I think that I probably was less than clear in my request for assistance.

 

The ICOM AT-500 auto-tuner isn't the issue. I've fabricated a cable between the rig and the tuner, as no commercially manufactured cable exist.

 

My concern is how can I control an amplifier and run the digital & logging software. With a solitary ACC DIN socket?

 

Digital ops isn't a problem, as the amps are not in line. However, when I operate SSB or CW and the amps are in use, I've effectively lost my ability to log via the computer..

 

Thanks for taking a minute to address my concerns.

 

If you have further thoughts on this issue, please don't hesitate to write.

 

tnx es 73 de K3SSB

 

Tom G, Sr.


Re: [IC-7000] Accessory DIN Socket

Robert Spencer
 

I run an amp and a SCS PTC II Pro pactor modem with a Mod2 Robust packet card.  The amp uses an Ameritron ARB704 and of course the 13 pin ACC also connects from the IC7000 to the modem.  I also run an IC2820.  I built a relay switching system so I can go to different configurations.  I tied the commons together so I can select between either radio and also a sound card device or packet.  The 6 pin dins are tied to either NO or NC contacts then the commons are tied so the NC or NO of a different relay contacts either go to the packet or to a sound card device.  This is all in a mobile setup.  I can switch to any configuration without having to swap cables.  I used instrumentation grade relays and screw in din connectors for the relay box.  This was expensive.  It cost close to $500 for parts and a good aluminum housing.  I used an Amphenol military type connector for the 13 pin ACC.  Nearly all the #2 pins were grounds, so they were tied together without relays.  Pay close attention to the grounding and shielding requirements for the PTC modem if that is what you are using.  Some shields cannot be grounded.  It will cause the modem to go into a transmit mode.
I went cheap for a while and hoped it would work, but I found out the hard way that I was constantly repairing solder connections due to the strain on the cables.  This system has been up for 5 months now without any issues.
Currently the IC7000 13 pin ACC provides the power for the PTC modem.  I am going to change that so I do not have to power up the 7000 just for packet with the IC2820.  The ALC is used by the ARB704 and the PTC modem.  I did not do any work to configure the system to share the ALC to use the amp in digital mode.  Even mobile, I do not need an amp for digital mode.
If you want a BOM, let me know.
Robert


Re: [IC-7000] Re: Accessory DIN Socket

Kenneth Dyer
 

Hope this helps its an ICOM stock OPC-599 Adaptor Cable 13-Pin, ACC connector to 7 Pin + 8 Pin ACC Connector.

I have used it on my ICOM 7000

 

73

Ken GW0RHC/HZ1GW/A92HC

 

 

From: ic7000@... [mailto:ic7000@...]
Sent: 28 January 2018 22:52
To: ic7000@...
Subject: RE: [IC-7000] Re: Accessory DIN Socket

 

 

Icom makes a split pigtail that goes from a 13 pin din to a 7 pin and 6 pin female din.

I believe it may show in your manual on the 7K

 

73

Van

WD6FGB

 

From: ic7000@... [mailto:ic7000@...]
Sent: Sunday, January 28, 2018 2:39 PM
To: ic7000@...
Subject: RE: [IC-7000] Re: Accessory DIN Socket

 

 

Good Evening Brian Et al:

 

I think that I probably was less than clear in my request for assistance.

 

The ICOM AT-500 auto-tuner isn't the issue. I've fabricated a cable between the rig and the tuner, as no commercially manufactured cable exist.

 

My concern is how can I control an amplifier and run the digital & logging software. With a solitary ACC DIN socket?

 

Digital ops isn't a problem, as the amps are not in line. However, when I operate SSB or CW and the amps are in use, I've effectively lost my ability to log via the computer.

 

Thanks for taking a minute to address my concerns.

 

If you have further thoughts on this issue, please don't hesitate to write.

 

tnx es 73 de K3SSB

 

Tom G, Sr.


Re: [IC-7000] Re: Accessory DIN Socket

Van
 

Icom makes a split pigtail that goes from a 13 pin din to a 7 pin and 6 pin female din.

I believe it may show in your manual on the 7K

 

73

Van

WD6FGB

 

From: ic7000@... [mailto:ic7000@...]
Sent: Sunday, January 28, 2018 2:39 PM
To: ic7000@...
Subject: RE: [IC-7000] Re: Accessory DIN Socket

 

 

Good Evening Brian Et al:

 

I think that I probably was less than clear in my request for assistance.

 

The ICOM AT-500 auto-tuner isn't the issue. I've fabricated a cable between the rig and the tuner, as no commercially manufactured cable exist.

 

My concern is how can I control an amplifier and run the digital & logging software. With a solitary ACC DIN socket?

 

Digital ops isn't a problem, as the amps are not in line. However, when I operate SSB or CW and the amps are in use, I've effectively lost my ability to log via the computer.

 

Thanks for taking a minute to address my concerns.

 

If you have further thoughts on this issue, please don't hesitate to write.

 

tnx es 73 de K3SSB

 

Tom G, Sr.


Re: [IC-7000] Re: Accessory DIN Socket

Tom Gregor
 

Good Evening Brian Et al:

I think that I probably was less than clear in my request for assistance.

The ICOM AT-500 auto-tuner isn't the issue. I've fabricated a cable between the rig and the tuner, as no commercially manufactured cable exist.

My concern is how can I control an amplifier and run the digital & logging software. With a solitary ACC DIN socket?

Digital ops isn't a problem, as the amps are not in line. However, when I operate SSB or CW and the amps are in use, I've effectively lost my ability to log via the computer.

Thanks for taking a minute to address my concerns.

If you have further thoughts on this issue, please don't hesitate to write.

tnx es 73 de K3SSB

Tom G, Sr.


Re: [IC-7000] IC-7000 Base Unit Only

Paul Hansen
 

As far as I know, Dave, it is not possible to run the 7000 without the control head. There’s no way to power up the body and it requires communications with the head. I guess somebody stole your control head from your car. I can always use 7000 parts so what did you have in mind for the body?

 

pwhansen@...          

 

Thank you,

 

Paul W. Hansen, W6XA

 

 

From: ic7000@... [mailto:ic7000@...]
Sent: January 28, 2018 14:44
To: ic7000@...
Subject: [IC-7000] IC-7000 Base Unit Only

 



Hello...

Is it possible to operate a IC-7000 base unit with the CT-17 and pc WITHOUT having a control head? if so how?

Anyone need another base unit?

ty
Dave WN4AFP

 





Re: [IC-7000] Re: Accessory DIN Socket

Brian (N2MLP)
 

https://www.universal-radio.com/catalog/hamtune/at500dia.jpg





From: ic7000@yahoogroups.com [mailto:ic7000@yahoogroups.com]
Sent: Sunday, January 28, 2018 8:57 AM
To: ic7000@yahoogroups.com
Subject: [IC-7000] Re: Accessory DIN Socket








Good Morning Brian:





The amplifiers in question are:






* Collins 30L1
* ICOM IC-2KL





The tuner is:





* ICOM AT-500





It's not a question of having the appropriate cables and jumpers, I have them. It appears to be more an issue of having a solitary accessory DIN socket on the 7000.





tnx K3SSB





Tom G, Sr.













[Non-text portions of this message have been removed]


IC-7000 Base Unit Only

daveedmo@...
 

Hello...

Is it possible to operate a IC-7000 base unit with the CT-17 and pc WITHOUT having a control head? if so how?

Anyone need another base unit?

ty
Dave WN4AFP



Re: Accessory DIN Socket

Steve W3AHL
 

The DATA port is the preferred interface for digital modes, which would free up the ACC port for other uses.

How will not using the ACC port for digital eliminate the ability to auto log?  That info is typically obtained from the CI-V interface.

Steve, W3AHL

---In ic7000@..., <k3ssb@...> wrote :

Good Afternoon Group:


I recently acquired a linear amplifier and was pondering over how to hook it up, the ACC socket is where I have my computer and digital comms programs currently running.


Sure, I could swap out the cables from digital operations to the running the amplifier on SSB/CW. But that would eliminate the ability to auto log... carrying this to the extreme... what if one wanted to operate with all of the following:


  • Digitally operations
  • Tuner
  • Amplifier


I probably answered my own questions... in that it's not possible (with the IC-7000). Are there any workarounds?.


tnx es 73 de K3SSB


Tom G, Sr.




Re: Accessory DIN Socket

Tom Gregor
 

Good Morning Brian:

The amplifiers in question are:

  • Collins 30L1
  • ICOM IC-2KL

The tuner is:

  • ICOM AT-500

It's not a question of having the appropriate cables and jumpers, I have them. It appears to be more an issue of having a solitary accessory DIN socket on the 7000. 

tnx K3SSB

Tom G, Sr.


Re: [IC-7000] Accessory DIN Socket

Brian (N2MLP)
 

What tuner and amp are you using would help

 

From: ic7000@... [mailto:ic7000@...]
Sent: Saturday, January 27, 2018 7:01 PM
To: ic7000@...
Subject: [IC-7000] Accessory DIN Socket

 

 

Good Afternoon Group:

 

I recently acquired a linear amplifier and was pondering over how to hook it up, the ACC socket is where I have my computer and digital comms programs currently running.



Sure, I could swap out the cables from digital operations to the running the amplifier on SSB/CW. But that would eliminate the ability to auto log... carrying this to the extreme... what if one wanted to operate with all of the following:



  • Digitally operations
  • Tuner
  • Amplifier

 

I probably answered my own questions... in that it's not possible (with the IC-7000).. Are there any workarounds?.

 

tnx es 7 3 de K3SSB

 

Tom G, Sr.

 

 


Accessory DIN Socket

Tom Gregor
 

Good Afternoon Group:


I recently acquired a linear amplifier and was pondering over how to hook it up, the ACC socket is where I have my computer and digital comms programs currently running.


Sure, I could swap out the cables from digital operations to the running the amplifier on SSB/CW. But that would eliminate the ability to auto log... carrying this to the extreme... what if one wanted to operate with all of the following:


  • Digitally operations
  • Tuner
  • Amplifier


I probably answered my own questions... in that it's not possible (with the IC-7000). Are there any workarounds?.


tnx es 73 de K3SSB


Tom G, Sr.




Re: [IC-7000] Re: Fw: Ron Baran signed Scan2018 documents

k4pwo@...
 

Sounds like you got an attempted click through payload malware/phishing/spam message. Luckily this group strips attachments.

Unless you are expecting the message, NEVER click on any attachments, even when the message appears to come from someone you know.



Perry K4PWO



From: ic7000@yahoogroups.com [mailto:ic7000@yahoogroups.com]
Sent: Saturday, January 27, 2018 2:03 PM
To: ic7000@yahoogroups.com
Subject: [IC-7000] Re: Fw: Ron Baran signed Scan2018 documents





There is nothing attached??

Joe
K2S








[Non-text portions of this message have been removed]


Re: Fw: Ron Baran signed Scan2018 documents

k2ds@...
 

There is nothing attached??

Joe
K2S


Re: [IC-7000] IC7000 Tuning Locked up

k2ds@...
 

Mark, Yes I tried them today and Yes I can tune it from the buttons on the Mike.

Joe


Re: [IC-7000] IC7000 Tuning Locked up

k2ds@...
 

I don't know since I did the reset all of the mem were cleared out. So there is nothing to check it on.


Re: [IC-7000] Re: Digital Modes and CAT on IC7000

Steven Linley
 

I really like WSJT-X as well as FLdigi, which I run through Commander (part of DXLab Suite of 8 apps).  One of the DXLab Suite of apps is WinWarbler, for RTTY, PSK, and CW.

WA8Y


On 1/24/2018 6:07 PM, sv2hws@... [ic7000] wrote:
 

Hello

As I could see there are positive reviews for xggcomms (and the FTDI chipset that these cables use) so I proceeded with ordering a Digimode-1-Icom cable from their ebay shop. The seller is indeed really helpful and quick to reply as Dale has mentioned.

This cable offers 600:600 ohms isolation for audio, Opto isolation for PTT, connection to CI-V for CAT and PTT using either RTS signal or CAT. The missing feature related to signalink is the external sound card, so I plan to use a 3rd party USB external sound card to separate digital operation sounds from other computer sounds. Audio levels can be configured from the computer.

The reason for my choice is of course money because I payed about 57EUR for this interface. The cheapest signalink I could find would cost around 155EUR and I would still need a CI-V cable to use CAT software which sums to about 3x times the money I payed now!

Regarding the non-muting Mic when using the 13pin socket on IC-7000, I talked about this with the seller and he replied that he can sent me a cable that has a 6pin plug for the DATA socket on the radio. All I needed to do was add a comment about this on the ebay checkout. That is what I did and I am currently waiting to receive and test it.

If anyone can suggest good LINUX software for digital modes or CAT or radio programming or anything else interesting I would really like to hear about it. I already know about FLdigi and CHIRP so I am waiting for other suggestions.

Thank you everyone for your helpful feedback
Triantafyllos, SV2HWS



Re: [IC-7000] Re: Digital Modes and CAT on IC7000

Helmut Wabnig
 

On 24 Jan 2018 23:07:23 +0000, you wrote:

Hello

As I could see there are positive reviews for xggcomms (and the FTDI chipset that these cables use) so I proceeded with ordering a Digimode-1-Icom cable from their ebay shop. The seller is indeed really helpful and quick to reply as Dale has mentioned.

This cable offers 600:600 ohms isolation for audio, Opto isolation for PTT, connection to CI-V for CAT and PTT using either RTS signal or CAT.. The missing feature related to signalink is the external sound card, so I plan to use a 3rd party USB external sound card to separate digital operation sounds from other computer sounds. Audio levels can be configured from the computer.
.....
I am using a ROLAND EDIROL UA-25 ex USB audio interface, everything
directly connected, no optocouplers, no transformers, and a selfmade
USB to serial PTT with one open collector transistor,
also DC connected to a laptop PC with docking station.

It works and there are no line noise and other interferences,
audio clear down to -90dB.
But it took me quite a lot of work to get the noise down.
Shielding and grounding are my specialty :-)
I only want to say, optcouplers and transformers may help or not,
depending on one's electronics skills.


OE8UWW


Re: Digital Modes and CAT on IC7000

sv2hws@...
 

Hello

As I could see there are positive reviews for xggcomms (and the FTDI chipset that these cables use) so I proceeded with ordering a Digimode-1-Icom cable from their ebay shop. The seller is indeed really helpful and quick to reply as Dale has mentioned.

This cable offers 600:600 ohms isolation for audio, Opto isolation for PTT, connection to CI-V for CAT and PTT using either RTS signal or CAT. The missing feature related to signalink is the external sound card, so I plan to use a 3rd party USB external sound card to separate digital operation sounds from other computer sounds. Audio levels can be configured from the computer.

The reason for my choice is of course money because I payed about 57EUR for this interface. The cheapest signalink I could find would cost around 155EUR and I would still need a CI-V cable to use CAT software which sums to about 3x times the money I payed now!

Regarding the non-muting Mic when using the 13pin socket on IC-7000, I talked about this with the seller and he replied that he can sent me a cable that has a 6pin plug for the DATA socket on the radio. All I needed to do was add a comment about this on the ebay checkout. That is what I did and I am currently waiting to receive and test it.

If anyone can suggest good LINUX software for digital modes or CAT or radio programming or anything else interesting I would really like to hear about it. I already know about FLdigi and CHIRP so I am waiting for other suggestions.

Thank you everyone for your helpful feedback
Triantafyllos, SV2HWS


Fw: Ron Baran signed Scan2018 documents

Ronald Baran
 

Hi,

I trust that you are doing well?

i have been trying to deliver the following document to you, kindly help me carefully go through the paragraph 3 page 2 let me know what you think concern the content and let me know if you agreed!

Kind Regards



Ron Baran?? DDS, MBA, MA
Willowbrook, IL
630-325-9857
W9XS
??

1781 - 1800 of 41398