Date   

Re: [IC-7000] IC-7000 Won't transmit

Gordon McCleery
 

Were you able to test your setup into a dummy load bypassing the

antenna system completely ? Verify your coax cable jumpers with an

ohmmeter. Let us know how you proceed.....Mac (w4glm)







________________________________
From: Keith <kd2cwq@...>
To: ic7000@...
Sent: Monday, January 21, 2013 1:16 PM
Subject: [IC-7000] IC-7000 Won't transmit

Hello and 73 to everyone.  I just joined the group and hope someone might have some input with the problem I'm having, it seems similar to the topic "Re: Strange issues with output power"

This is the description of the problem I just sent to Icom:

I plan to send my IC-7000 (S/N 0506030)in for repairs but thought I would give

you some idea of the problem in the hope that you might be able to give me a

preliminary assessment of the problem and range of cost.

Other operating conditions:
LDG AT7000 autotuner (found to be working properly)
Buckmaster 300W 7-Band OCF dipole
SWR (according to the internal meter) <= 1 on all HF bands
OPEC 2M/440MHz dual band vertical antenna

SSB

RF level set to 100%

I noticed that the ALC, Po, and COM meters were not moving when I tried to

transmit on SSB. 

As I tried to adjust the mic gain according to the instructions in the manual I

found that there was no reading on the ALC meter and that adjusting the main

knob had no effect on the meter reading.

FM

RF level set to 100%

I was able to transmit on the 2M band but:
- The ALC reading went full scale into the red
- Attempts to adjust the ALC -- the ALC reading went full scale into the red when the PTT was activated and adjusting the main control know had no effect on the meter reading.
-The strength of my transmission signal grew weaker as the transmission progressed.

CW
My Elmer, and former owner of the radio, transmitted a carrier and found the peak output to be 5W.

I understand that you will be able to give a better assessment once you can test the radio but any preliminary thoughts would be appreciated.

Sincerely,
Keith Obrosky KD2CWQ
73!



------------------------------------

Community email addresses:
  Post message: IC7000@...
  Subscribe:    IC7000-subscribe@...
  Unsubscribe:  IC7000-unsubscribe@...
  List owner:  IC7000-owner@...

*******************************************************************
"Spam, racism, name-calling, vulgarity, religious or political propaganda, personal insults and/or verbal abuse will not be tolerated in this group at any time. Any member posting such material will be placed on moderated status, and is subject to deletion and banning."
*******************************************************************
Yahoo! Groups Links



[Non-text portions of this message have been removed]


Re: [IC-7000] Re: 10.7MHz IF Output?

Mark Schoonover
 

Yes, this is exactly what I'm looking for. Thanks for the links.

73 - Mark Schoonover - KA6WKE
http://www.ka6wke.net
QSX: 21.446 SSB & 29.6 FM



On Sat, Jan 19, 2013 at 3:04 AM, dajetzi <da_kaeptn@...> wrote:

**


Here is a pdf which shows how to find 1IF stage in IC7000

http://groups.yahoo.com/group/ic7000/files/How%20to%20connect%20a%20SDR%20dongle%20to%20IC7000.pdf

Also a nice project you can find here. Panadapter for FT-817.
http://www.w1ghz.org/small_proj/small_proj.htm



--- In ic7000@..., Mark Schoonover wrote:

I'm wondering if there's a mod for the 7000 to provide IF output. Would
like to have a real spectrum scope. Is it possible? Googling around
mostly
returns hits on the R7000 receiver.

73 - Mark Schoonover - KA6WKE
http://www.ka6wke.net
QSX: 21.446 SSB & 29.6 FM


[Non-text portions of this message have been removed]


IC-7000 Won't transmit

Keith Obrosky
 

Hello and 73 to everyone. I just joined the group and hope someone might have some input with the problem I'm having, it seems similar to the topic "Re: Strange issues with output power"

This is the description of the problem I just sent to Icom:

I plan to send my IC-7000 (S/N 0506030)in for repairs but thought I would give

you some idea of the problem in the hope that you might be able to give me a

preliminary assessment of the problem and range of cost.

Other operating conditions:
LDG AT7000 autotuner (found to be working properly)
Buckmaster 300W 7-Band OCF dipole
SWR (according to the internal meter) <= 1 on all HF bands
OPEC 2M/440MHz dual band vertical antenna

SSB

RF level set to 100%

I noticed that the ALC, Po, and COM meters were not moving when I tried to

transmit on SSB.

As I tried to adjust the mic gain according to the instructions in the manual I

found that there was no reading on the ALC meter and that adjusting the main

knob had no effect on the meter reading.

FM

RF level set to 100%

I was able to transmit on the 2M band but:
- The ALC reading went full scale into the red
- Attempts to adjust the ALC -- the ALC reading went full scale into the red when the PTT was activated and adjusting the main control know had no effect on the meter reading.
-The strength of my transmission signal grew weaker as the transmission progressed.

CW
My Elmer, and former owner of the radio, transmitted a carrier and found the peak output to be 5W.

I understand that you will be able to give a better assessment once you can test the radio but any preliminary thoughts would be appreciated.

Sincerely,
Keith Obrosky KD2CWQ
73!


(No subject)

WILLIAM L ROGERS <w4wlr@...>
 


ic7000-unsubscribe@yahoogroups.com

eric <f1smv@...>
 


Re: [IC-7000] Re: IC-7000 don´t want to switch on

Ivan Silva <ivan@...>
 

I advise to follow all the way from 12 v up to the control unit. I've fixed
two IC7000 that have had same problems in the metalizing of the holes on
the printed circuit board where the thread passes from one side to the other
side.



Ivan-PY1YB



_____

From: ic7000@... [mailto:ic7000@...] On Behalf Of
VE3FMC
Sent: sábado, 19 de janeiro de 2013 22:59
To: ic7000@...
Subject: [IC-7000] Re: IC-7000 don´t want to switch on





I had that problem once after I moved the radio. It was due to the fact that
the face plate was loose, must have hit the release when I moved the radio.
Reseated it and the radio was fine after that.
Rick

--- In ic7000@... <mailto:ic7000%40yahoogroups.com> , "dajetzi"
wrote:


Hello,
did the trx not switch on at all, means there is no display visible?
How do you did a reset when trx did not switch on?

Have you checked the contacts from the front panel?
Maybe the display unit get short.
Take a look here.

Relay klicking
0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-&#92;
click-no-power-problem.pdf>

73 de DO1KLM, Sigi




[Non-text portions of this message have been removed]




[Non-text portions of this message have been removed]


Re: IC-7000 don´t want to switch on

VE3FMC <ve3fmc@...>
 

I had that problem once after I moved the radio. It was due to the fact that the face plate was loose, must have hit the release when I moved the radio. Reseated it and the radio was fine after that.
Rick

--- In ic7000@..., "dajetzi" wrote:


Hello,
did the trx not switch on at all, means there is no display visible?
How do you did a reset when trx did not switch on?

Have you checked the contacts from the front panel?
Maybe the display unit get short.
Take a look here.

Relay klicking
0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-&#92;
click-no-power-problem.pdf>

73 de DO1KLM, Sigi




[Non-text portions of this message have been removed]


Re: Retransmission of Received Audio

dajetzi <da_kaeptn@...>
 

Hi,
you're right. It is not possible with the trx itself.
For this situations i am using HRD.

73 de DO1KLM, Sigi

--- In ic7000@..., Eugene Coggins wrote:

Hello everyone:

I am new to amateur radio so forgive me if I fail to use the proper
nomenclature. And I am a proud owner of an IC-7000.

Several of my local contacts who own Kenwoods have the ability to
record my transmission for about five or ten seconds and transmit it
back to me. That way I can hear how I sound on the radio. This can be
a very valuable tool.

I have read and reread the chapter on Voice Recorder Functions in the
manual. It seems that you can record a received transmission and are
only able to play it back, but not retransmit it. You can record your
voice through the microphone and transmit it. But it seems you cannot
retransmit received audio.

Am I missing something?

Thanks

Gene
73
KB3ZIP


Re: IC-7000 don´t want to switch on

dajetzi <da_kaeptn@...>
 

Hello,
did the trx not switch on at all, means there is no display visible?
How do you did a reset when trx did not switch on?

Have you checked the contacts from the front panel?
Maybe the display unit get short.
Take a look here.

Relay klicking
<http://f1.grp.yahoofs.com/v1/ENH6UKvZX8A49yzBZ1UM5825q8L7U42zZrY9K8i3p1\;
0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-&#92;
click-no-power-problem.pdf>

73 de DO1KLM, Sigi


Re: IC-7000 don´t want to switch on

Tong Meco
 

Hi EA1RJ,

Your friend problem like S21RC,but he solve the problem and repair it by himself.

http://www.s21rc.net/?p=49


73....VR2XXZ

--- In ic7000@..., "ea1rj" wrote:

Hi all

i´m new in the group, i had an IC-7000 during 2 years and i sold it, i think it´s a great TRX (mine got the driver failure in guarente time) but it´s realy a nice TRX. Noew i have one FT-2000 and one TS-2000X, enought for me :)

I´m trying to help a friend that don´t speak english.

Her IC-7000 don´t want to switch on, when he press the on button, he ear the sound of a relay but the TRX don´t switch on.

we have check all fuses and we have made a reset but we have not found the mistake.

Anyone can help us?

tnx es 73 all


Re: [IC-7000] IC-7000 don´t want to switch on

Tong Meco
 

Hi EA1RJ,
 
    Your friend problem like S21RC,but he solve the problem and repair it by himself. 
 
http://www.s21rc.net/?p=49
 
 
73....VR2XXZ
 
 
 2013年1月19日 星期六,ea1rj <ea1rj@...> 寫道﹕


寄件人: ea1rj <ea1rj@...>
主題: [IC-7000] IC-7000 don´t want to switch on
收件人: ic7000@...
日期: 2013年1月19日,星期六,下午3:27



 



Hi all

i惴 new in the group, i had an IC-7000 during 2 years and i sold it, i think it愀 a great TRX (mine got the driver failure in guarente time) but it愀 realy a nice TRX. Noew i have one FT-2000 and one TS-2000X, enought for me :)

I惴 trying to help a friend that don愒 speak english.

Her IC-7000 don愒 want to switch on, when he press the on button, he ear the sound of a relay but the TRX don愒 switch on.

we have check all fuses and we have made a reset but we have not found the mistake.

Anyone can help us?

tnx es 73 all








[Non-text portions of this message have been removed]


IC-7000 don´t want to switch on

ea1rj <ea1rj@...>
 

Hi all

i´m new in the group, i had an IC-7000 during 2 years and i sold it, i think it´s a great TRX (mine got the driver failure in guarente time) but it´s realy a nice TRX. Noew i have one FT-2000 and one TS-2000X, enought for me :)

I´m trying to help a friend that don´t speak english.

Her IC-7000 don´t want to switch on, when he press the on button, he ear the sound of a relay but the TRX don´t switch on.

we have check all fuses and we have made a reset but we have not found the mistake.

Anyone can help us?

tnx es 73 all


Re: 10.7MHz IF Output?

dajetzi <da_kaeptn@...>
 

Here is a pdf which shows how to find 1IF stage in IC7000
http://groups.yahoo.com/group/ic7000/files/How%20to%20connect%20a%20SDR%20dongle%20to%20IC7000.pdf

Also a nice project you can find here. Panadapter for FT-817.
http://www.w1ghz.org/small_proj/small_proj.htm

--- In ic7000@..., Mark Schoonover wrote:

I'm wondering if there's a mod for the 7000 to provide IF output. Would
like to have a real spectrum scope. Is it possible? Googling around mostly
returns hits on the R7000 receiver.

73 - Mark Schoonover - KA6WKE
http://www.ka6wke.net
QSX: 21.446 SSB & 29.6 FM


Re: 10.7MHz IF Output?

dajetzi <da_kaeptn@...>
 

Maybe this is what are you searching for.
The IC7000 has first IF at 124,487MHz for AM/FM/SSB/CW/RTTY.
http://groups.yahoo.com/group/ic7000/message/33057

73 de DO1KLM, Sigi

--- In ic7000@..., Mark Schoonover wrote:

I'm wondering if there's a mod for the 7000 to provide IF output. Would
like to have a real spectrum scope. Is it possible? Googling around mostly
returns hits on the R7000 receiver.

73 - Mark Schoonover - KA6WKE
http://www.ka6wke.net
QSX: 21.446 SSB & 29.6 FM


Triathlon DX Contest

sv5byr
 

Get Ready for the first Triathlon DX Contest at Saturday, 2/2/2013
RTTY, SSB and CW in a single contest!!!

A big surprise award!!!

Team contesting and many more...
Details including rules in English, Italian and Greek in our site:

http://www.triathlon-dx-contest.gr


10.7MHz IF Output?

Mark Schoonover
 

I'm wondering if there's a mod for the 7000 to provide IF output. Would
like to have a real spectrum scope. Is it possible? Googling around mostly
returns hits on the R7000 receiver.

73 - Mark Schoonover - KA6WKE
http://www.ka6wke.net
QSX: 21.446 SSB & 29.6 FM


Retransmission of Received Audio

Eugene Coggins
 

Hello everyone:

I am new to amateur radio so forgive me if I fail to use the proper nomenclature. And I am a proud owner of an IC-7000.

Several of my local contacts who own Kenwoods have the ability to record my transmission for about five or ten seconds and transmit it back to me. That way I can hear how I sound on the radio. This can be a very valuable tool.

I have read and reread the chapter on Voice Recorder Functions in the manual. It seems that you can record a received transmission and are only able to play it back, but not retransmit it. You can record your voice through the microphone and transmit it. But it seems you cannot retransmit received audio.

Am I missing something?

Thanks

Gene
73
KB3ZIP


Re: fellow user of IC-7000

k0cwo
 

Welcome Mate!

L love the quote, wow!

73, BJ
k0cwo

--- In ic7000@..., Malcolm Cooper wrote:

Just a short note to introduce myself. My name is Malcolm, call sign is VK2AB situated in Yass NSW AU about 75 killometres Nth West of the Australian Capital Territory.
Looking forward to hearing from the group.
 VK2AB
My life is not a journey to the grave with the intention
of arriving safely in a well presevedbody. I will skid in
broadside after beingthoroughly used up,
totally worn out and loudly shouting...Wow...What a ride.
VK2AB Malcolm

[Non-text portions of this message have been removed]


Re: [IC-7000] Social engineering (was: No subject)

Dean Gibson AE7Q <yahoo@...>
 

Automatically clicking on links in eMails (no matter *WHO* they appear
to be from), is a REALLY BAD IDEA.

Additional clues were available in the original eMail:

1. No subject.
2. No real text.


Be safe ...

On 2013-01-17 07:02, Rick McCusker wrote:
Has anyone else clicked on this link? I did, thinking I was going to a site with tips on the IC-7000. Instead, I get a Fox News page talking about Dr. Oz and his raspberry breakthrough to weight loss....

Rick, WF6O


keying voice keyer memories thru PC control

ww3s@...
 

----- Original Message -----
anyone know if its possible to trigger the voice keyer memories thru the CAT port?

8921 - 8940 of 41742