Try View – Find Lost Windows It might just be hiding. 73 Dave GM4NFI

Hi I am logged on as Administrator but when I look at Generic USB Hub Properties I get The Power and Advanced Tabs are missing. I am running Windows 10 Pro. 19043.1348 I came across this article https

Hi I have just had a look at what you suggested and found something strange. If I look at Device manager for Ports – I get this. So I am looking for Port_#0002.Hub_#0011 Now if I look at Universal Ser

The usual way round this problem is to change the Com Port assigned to Logger32 but I had tried (one by one) all the unassigned Com ports up to 12 without any success. Just before doing a reboot I wen

Hi This is what I get. Com 3 is where the TS 590 is connected and Com 5 has an Arduino connected. It is connecting, uploading and giving Serial output OK. Once, switching from Radio 1 to Radio 2 then

Hi Thanks for the advice. I have tried it without a re-boot and I am still getting “Invalid Port xx” I have tried most ports and still get it. I will see what happens after a reboot but this is a pain

I have been running Logger32 for years now without any issues until of late. Environment Windows 10.0.19043.1348 Logger32 4.0.287 Rig Kenwood TS 590S I have had a good look round the group for previou

Hi I cannot reproduce this error. But how is a frequency of 20.967MHz arise as its out of band? Does it still happen if the DX spot is within the band? It could be due to an error or omission in your

The current version is now V4.0.283 Dave GM4NFI

Hi I didn’t know that you could run a file from a shortcut with administrator privileges so easily you “live and learn” HI Its an easier method than what I was doing i.e. going to the logger32.exe and

Hi Its easiest if it’s the actual logger32.exe file that you run as administrator. If you just select a normal shortcut to logger32.exe and try to run that as administrator the actual logger.exe file

Hi Gary I read the section on page 35 which said “Hinson tip: strange things happen if Logger32 isn’t given a default mode for the current VFO frequencies … so define CW from the very bottom edge to t

I have had another close look at this issue and I seem to have solved it. I am posting this just in case it helps someone else. My problem only affected 80M and 40M Suppose I am on 7.028MHz and the ba

Hi Bob TNX fer advice. JTDX is not on. CW Machine was open but I have closed it, closed logger32 and then reloaded it. I am on 7.028MHz by rig dial and logger 32 also has the frequency correct at 7.02

Hi TNX fer replies I had a look at this before posting and I could not see anything wrong. Below is my current settings. Frequency is correct but its still saying 20M band. When I log a 40M QSO it log

I am running Logger32 V4.0.274 Rig is a TS 590S (latest firmware) Polling Interval is 500 (was 1000) Baud is 9600 I have studied Section 49.6 Kenwood TS-480/TS-590 in the “HelP File” and my setup seem

I have just upgraded to 3.50.418 this morning without any issues. Dave GM4NFI

Hi I have registered with LOTW GM4NFI EA7/GM4NFI GM4NFI/P GM4NFI/M I also have GM4NFI/MM but note /MM cannot have DXCC Depending on which callsign I used at the time of the QSO I just upload to that c

I think you are correct. I am running Kasperski and Windows Defender has been de-activated and not by me. Note that so far I have never had any issues with Kasperski and Logger32 73 Dave GM4NFI

After no issues for several days this afternoon the DX spots were not appearing on the map. As is normal when this happens the Telnet and DX Spots windows were populating pefectly. Shuting down and re