Date   

Re: Statistics

Bob
 

Try the COMPLETE LOGBOOK option. SeventyThree(s).


On December 2, 2019 at 3:06 AM Panos <sv1grn@...> wrote:

Hi dear friends, in the awards / dxcc screen the complete logbook option contains statistics from the whole logbook. Other options persist for yearly statistics. But this yearly results are only for the chosen year.  How I can extract cumulative results without using external programmes? For example when choosing 2018 I need to see cumulative statistics from the beginning of my log including 2018. Is there any solution? Thanks 73


 


Re: Spot display 6600M

Bob
 

On December 1, 2019 at 10:33 PM rodman@... wrote:

register? 

 


Statistics

Panos
 

Hi dear friends, in the awards / dxcc screen the complete logbook option contains statistics from the whole logbook. Other options persist for yearly statistics. But this yearly results are only for the chosen year.  How I can extract cumulative results without using external programmes? For example when choosing 2018 I need to see cumulative statistics from the beginning of my log including 2018. Is there any solution? Thanks 73


Re: Spot display 6600M

David KN2M
 

register? 


Re: FTDX 3000

Steve Sawyer
 

Have not seen anyone answer you so will say this.  When the FTDX 5000 came out I had to use the FT 2000 in Logger 32 until they added the 5000.  I would say tell your friend to use either the 2000 or 5000.

Steve (KT0DX)

On 12/1/2019 21:38, Dave Colliau wrote:
Whats everyone using for a rig in logger 32 to make the 3000 work with cat control.
Asking for a friend .. Really
Dave N8DC


Re: FTDX 3000

Dave Colliau
 

Whats everyone using for a rig in logger 32 to make the 3000 work with cat control.
Asking for a friend .. Really
Dave N8DC


Re: trouble with dx spots window

ja1nlx
 

Hello

FT8/WSJT

I do not know what TRX you are using and how you connect audio between
PC and TRX.
Re-check soundcard selection in WSJT setting taable and re-check sound in
device in TRX.

CW machine

I do not know what mode you select in CW machine. I do not know how you connect
CW keying cable between TRX and PC.
There are 3 selectable options in CW machine. Which is selected ?

More details are needed for us to answer....

73

On 2019/12/02 1:16, Matthias Bellmann wrote:
Hi
i am using a new computer win 10 prof. as administrator.
Now i am trying to make logger32 3.50.402 work as it was before. 
There are several problems:
 
1. FT8 / WSJT
The trcvr does not respond to the sound card out signal. PTT works, wsjt is reveiving.
 
 
2. CW machine similar problem. PTT works, cw machine is keying,but cw signal is ignored by trcvr. Use COM1 (real serial) und com4 (USB). Always same result. Did test every possible combination in the cw machine keyer setup. There muzst be something i did not realize.
 
3. I am connected with telnet dx-cluster. It works fine. dx spots are displayed in the telnet window but dx spots windows remains empty. Only WWV announcement and ann messages are displayed. All blocking filter in are disabled. 
 
PLEASE NO ANSWER "read help file". I did read help for many hours and did try many settings, now i gave up.
 
Any answer well be appreciated.
 
 
 
--
73 de aki
JA1NLX


Re: Spot display 6600M

Bob
 

... other then the need for a reboot and possibly re-register as mentioned before), nothing comes to mind. 73.

On December 1, 2019 at 2:29 PM rodman@... wrote:

Bob, I DID rename the modified file to reflect the original expected name.  When I did this, Logger32 would not run.  When I renamed the original file to MSComm32.Ocx, (and changed the new modified file name so that there would not be two files with the same name) the program loaded and operated as before.  In your experience, this isn't some stupid thing like the file needs a registry hack to repoint to the new file location and remove traces of the original is it?  Thanks.

 


Re: Export ADIF Locked

HI3B Radhames
 

Hi Bob:

Done.....Solved
Thanks.
As I said you I did check and unchecked All Operators and received 
same info in the small window, but  stay  checked the
box "Export all new Qsos since of last ADIF export".
I did uncheck and DONE, all export did.
73,
Radhames, HI3B


From: hamlogger@groups.io <hamlogger@groups.io> on behalf of Bob <k4cy@...>
Sent: Sunday, December 1, 2019 2:38 PM
To: hamlogger@groups.io <hamlogger@groups.io>
Subject: Re: [hamlogger] Export ADIF Locked
 
Is this option enabled and/or checked? 73.


On December 1, 2019 at 1:23 PM HI3B Radhames <hi3b@...> wrote:

Hi guys:

After a couple of month with my laptop damaged,
I try to export all my contacts and the Export ADIF
the function does not work.
Appear a window titled "I can't let you do this..."
with the following info:
"The last ADIF export from this Logbook was made with the
HI3AB filter option selected. You no have the ALL OPERATORS 
filter enabled. I don't know your last exported QSO for this filter option".
I did uncheck ALL OPERATORS and check only HI3AB (my previous call),
and appear the same info again.
 Otherwise, I  would like someone with a bit of free time, to see my configuration remotely, via TeamViewer.
Thanks in advance.
Who could help me?


73,
Radhames, HI3B
 

--
HI3B

 

--
HI3B


Re: Spot display 6600M

David KN2M
 

Bob, I DID rename the modified file to reflect the original expected name.  When I did this, Logger32 would not run.  When I renamed the original file to MSComm32.Ocx, (and changed the new modified file name so that there would not be two files with the same name) the program loaded and operated as before.  In your experience, this isn't some stupid thing like the file needs a registry hack to repoint to the new file location and remove traces of the original is it?  Thanks.


Re: Export ADIF Locked

Bob
 

Is this option enabled and/or checked? 73.


On December 1, 2019 at 1:23 PM HI3B Radhames <hi3b@...> wrote:

Hi guys:

After a couple of month with my laptop damaged,
I try to export all my contacts and the Export ADIF
the function does not work.
Appear a window titled "I can't let you do this..."
with the following info:
"The last ADIF export from this Logbook was made with the
HI3AB filter option selected. You no have the ALL OPERATORS 
filter enabled. I don't know your last exported QSO for this filter option".
I did uncheck ALL OPERATORS and check only HI3AB (my previous call),
and appear the same info again.
 Otherwise, I  would like someone with a bit of free time, to see my configuration remotely, via TeamViewer.
Thanks in advance.
Who could help me?


73,
Radhames, HI3B
 

--
HI3B

 


Export ADIF Locked

HI3B Radhames
 

Hi guys:

After a couple of month with my laptop damaged,
I try to export all my contacts and the Export ADIF
the function does not work.
Appear a window titled "I can't let you do this..."
with the following info:
"The last ADIF export from this Logbook was made with the
HI3AB filter option selected. You no have the ALL OPERATORS 
filter enabled. I don't know your last exported QSO for this filter option".
I did uncheck ALL OPERATORS and check only HI3AB (my previous call),
and appear the same info again.
 Otherwise, I would like someone with a bit of free time, to see my configuration remotely, via TeamViewer.
Thanks in advance.
Who could help me?


73,
Radhames, HI3B
 

--
HI3B


Re: ODP: ODP: [hamlogger] CW machine

Bob
 

Thanks, I looked at the Silicon Labs spec sheet for their CT2015. No magic there - The enhanced vs standard mostly has to do with settings, Data bits and stop bits are fixed on the standard port to 8 and 1. Also the enhanced port baud rate is from 300 bps to 2 Mbps whereas the standard port is 2400 bps to 921600 bps. 73.

On December 1, 2019 at 11:17 AM Andy VA3PL <va3pl@...> wrote:

 
Hi Bob
I am not computer wiz, just the computer user.
These are com ports created by YAESU provided driver. It is Silicon Labs driver.

Silicon Labs Dual CT2105 USB UART Bridge Enhanced COM Port (in my case COM5 used for CAT)
Silicon Labs Dual CT2105 USB UART Bridge Standard COM Port (in my case COM6 used for CW, Audio, RTTY)

Andy SP9KR




Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Bob <k4cy@...>
Wysłane: niedziela, 1 grudnia 2019 16:28
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: ODP: [hamlogger] CW machine
 
What is an enhanced virtual port, and how/why is it necessary for your PC to CAT connection? 73.
On November 30, 2019 at 3:20 AM Andy VA3PL <va3pl@...> wrote:

 
Vince
Go to page 94 and read it and understand.

As a test just loaded N1MM set it up using ENHANCED virtual port for CAT and configured REGULAR virtual port for CW and it work nicely.

Also on 101D go to CW SETTING and change there to PC KEYING using DTR.

CW work nicely in N1MM but not using Logger32 CW MACHINE.

Andy SP9KR

Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Vince Shirley <vince.g0orc@...>
Wysłane: sobota, 30 listopada 2019 00:29
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: [hamlogger] CW machine
 
Hi Bob,

I still standby what I say in that there is nothing in the manual to suggest that CW may be sent down the USB port and I have never managed to make it work. I use an external interface should I wish to use electronic keying of CW

RTTY is supported as shown on P66 of the manual.  There is no such entry for CW.

The one thing that enables us to sleep soundly in our beds is that we don't have guns available to buy from our local supermarkets.  Oh, and our politicians may be the least respected members of our society but at least we haven't got Mr. Trump.  For that we are eternally grateful.

Vince 

On Fri, 29 Nov 2019 at 23:07, Bob < k4cy@...> wrote:
Vince, before you drift off into the arms of Morpheus (then wake up screaming from your nightmare of being on London Bridge at the wrong time) ... remember this message from the originator of the thread ...

Yes, there are two USB ports. One is enhanced for CAT and second USB is for other thinks, I have tried many combinations using one or the other and still no CW trough USB cable.
I been trying to avoid hurting somebody saying that other well known contest software provide capability of configuring CW trough USB cable and it works.
I was told by someone that "driver for Logger32 CW machine need to be updated".

SeventyThree(s).
On November 29, 2019 at 5:47 PM Vince Shirley < vince.g0orc@...> wrote:

At last - the voice of sanity.

Thanks Darren.  I said in the early days of this thread that the menu item relates to the keying of the radio and not sending CW which was something I worked out when I briefly owned an FTdx3000 which was very similar.in this respect. 

I gave up because no-one was listening.

There is nothing in the manual to say that CW may be sent down the radio's USB port.  If some operators have got it work then you are better than me and I'd love to know how you have done it using CW machine in Logger32.

I failed to get it to work with the FTdx3000 which had essentially the same menu item at the FTdx101.   If I remember correctly the FTdx5000 had PC keying in the menu but it had not been activated and was waiting for a software update.

I'll go and have lie down now...

Regards

Vince G0ORC





On Fri, 29 Nov 2019 at 14:10, Darren Collins (G0TSM) < daz@...> wrote:

I don't own an FTDX101 (I have the FTDX5K) but looking at the user manual it suggests that PC KEYING relates to the PTT and not to the CW Keying. If you look at the settings for the other modes it has the same options but for the other modes says its for RPTT SELECT. So it appears to be badly worded.

[RTTY] RPTT SELECT - DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 90))

[CW] PC KEYING -  DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 94))

I would imagine that Yaesu would be able to implement CW Keying via a software update, so its just down to the FTDX101 owners to request the feature. I recall that someone at Yaesu USA ran a 'wish list' for the FTDX5000 when it came out, so they are probably doing the same for the 101.

73 Darren G0TSM



On 28/11/19 21:10, Andy None via Groups.Io wrote:
Vince
Same here. radio keys and unkeys but no CW is send.
I give up also and went by using WinKeyer USB.
Been trying to use enhanced or regular USB port (they have different COM number) without success.

Andy SP9KR

On Thursday, November 28, 2019, 5:25:01 p.m. GMT+1, Vince Shirley <vince.g0orc@...> wrote:



I give up with this - there is nothing in the manual save for an entry in the CW MENU section which describes how to key the radio via its own USP port.

The radio keys and unkeys OK - but no CW is sent

My last word on the subject.

Vince G0ORC


On Thu, 28 Nov 2019 at 16:04, Vince Shirley via Groups.Io <vince.g0orc= gmail.com@groups.io> wrote:
Yes Mike, quite so.

But it doesn't work! 

Did you not read the rest of the message?

Vince

On Thu, 28 Nov 2019 at 15:29, Mike < ch25@...> wrote:
On Thu, Nov 28, 2019 at 03:59 PM, Vince Shirley wrote:
Thank you - I'm quite prepared to eat a large portion of humble pie and admit that I was wrong, but I just can't get it this to work. 
As written in the manual.
Mike

 

 


 

 

 


 

 


Re: Spot display 6600M

Bob
 

I put the file, into the two directories with the name 3dff00MSComm.Ocx, renamed the original file 3D1000MSComm.Ocx and dropped the 3dff00 on the new file in BOTH locations where I found the file.

I read this twice, and I'm still confused ... The modified file must be named MSComm32.ocx, that is what Logger32 is looking for. Also, a reboot of the PC is probably in order so that the modified file is loaded. 73.

On December 1, 2019 at 12:03 PM rodman@... wrote:

Bob, I am pretty sure I did what you suggested, but Logger 32 will not run at all unless I put the original .Ocx file back in the two directories.

Summary:  I used HxD to modify MSComm32.Ocx with that exact name with the 3D FF 00 modification.  I put the file, into the two directories with the name 3dff00MSComm.Ocx, renamed the original file 3D1000MSComm.Ocx and dropped the 3dff00 on the new file in BOTH locations where I found the file.  Both directories then had the modified .Ocx file (I checked) but Logger32 would NOT run unless I renamed the original files.  An error message came up, listing MSCOMM.OCX (IN CAPITALS) as the source of the error.  I then put the original files with original names back in.  I am operating the computer by remote control.  I did not restart and did not initiate a restore point either.

Logger 32 is running as before with the COM19 warning on start up.

??  Thanks

 


Re: Spot display 6600M

David KN2M
 

Bob, I am pretty sure I did what you suggested, but Logger 32 will not run at all unless I put the original .Ocx file back in the two directories.

Summary:  I used HxD to modify MSComm32.Ocx with that exact name with the 3D FF 00 modification.  I put the file, into the two directories with the name 3dff00MSComm.Ocx, renamed the original file 3D1000MSComm.Ocx and dropped the 3dff00 on the new file in BOTH locations where I found the file.  Both directories then had the modified .Ocx file (I checked) but Logger32 would NOT run unless I renamed the original files.  An error message came up, listing MSCOMM.OCX (IN CAPITALS) as the source of the error.  I then put the original files with original names back in.  I am operating the computer by remote control.  I did not restart and did not initiate a restore point either.

Logger 32 is running as before with the COM19 warning on start up.

??  Thanks


Re: trouble with dx spots window

Bob
 

1, When operating FT8, Logger32 does not send/receive audio. Check you PC Sound cards configuration and you WSJT-X configuration.
2. What radio are you using? There has just been a very long thread on the reflector about CW keying on a Yaesu USB port not working.
3. What is the caption of the DX Spots Window? 

SeventyThree(s).

On December 1, 2019 at 11:16 AM Matthias Bellmann <Dk4wd@...> wrote:

Hi
i am using a new computer win 10 prof. as administrator.
Now i am trying to make logger32 3.50.402 work as it was before. 
There are several problems:
 
1. FT8 / WSJT
The trcvr does not respond to the sound card out signal. PTT works, wsjt is reveiving.
 
 
2. CW machine similar problem. PTT works, cw machine is keying,but cw signal is ignored by trcvr. Use COM1 (real serial) und com4 (USB). Always same result. Did test every possible combination in the cw machine keyer setup. There muzst be something i did not realize.
 
3. I am connected with telnet dx-cluster. It works fine. dx spots are displayed in the telnet window but dx spots windows remains empty. Only WWV announcement and ann messages are displayed. All blocking filter in are disabled. 
 
PLEASE NO ANSWER "read help file". I did read help for many hours and did try many settings, now i gave up.
 
Any answer well be appreciated.
 
 
 

 


Re: ODP: ODP: [hamlogger] CW machine

Dave Colliau
 

I never got any of the enhanced ports Icom or Yaesu to work cw . I just used my old trusty home brew cw cable and a standard port and all is good. Since I had the cable from previous rigs and knew it worked i never really went too far with the cw machine and the keying.
Dave N8DC

On December 1, 2019 at 11:17 AM Andy VA3PL <va3pl@...> wrote:

 
Hi Bob
I am not computer wiz, just the computer user.
These are com ports created by YAESU provided driver. It is Silicon Labs driver.

Silicon Labs Dual CT2105 USB UART Bridge Enhanced COM Port (in my case COM5 used for CAT)
Silicon Labs Dual CT2105 USB UART Bridge Standard COM Port (in my case COM6 used for CW, Audio, RTTY)

Andy SP9KR




Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Bob <k4cy@...>
Wysłane: niedziela, 1 grudnia 2019 16:28
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: ODP: [hamlogger] CW machine
 
What is an enhanced virtual port, and how/why is it necessary for your PC to CAT connection? 73.
On November 30, 2019 at 3:20 AM Andy VA3PL <va3pl@...> wrote:

 
Vince
Go to page 94 and read it and understand.

As a test just loaded N1MM set it up using ENHANCED virtual port for CAT and configured REGULAR virtual port for CW and it work nicely.

Also on 101D go to CW SETTING and change there to PC KEYING using DTR.

CW work nicely in N1MM but not using Logger32 CW MACHINE.

Andy SP9KR

Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Vince Shirley <vince.g0orc@...>
Wysłane: sobota, 30 listopada 2019 00:29
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: [hamlogger] CW machine
 
Hi Bob,

I still standby what I say in that there is nothing in the manual to suggest that CW may be sent down the USB port and I have never managed to make it work. I use an external interface should I wish to use electronic keying of CW

RTTY is supported as shown on P66 of the manual.  There is no such entry for CW.

The one thing that enables us to sleep soundly in our beds is that we don't have guns available to buy from our local supermarkets.  Oh, and our politicians may be the least respected members of our society but at least we haven't got Mr. Trump.  For that we are eternally grateful.

Vince 

On Fri, 29 Nov 2019 at 23:07, Bob < k4cy@...> wrote:
Vince, before you drift off into the arms of Morpheus (then wake up screaming from your nightmare of being on London Bridge at the wrong time) ... remember this message from the originator of the thread ...

Yes, there are two USB ports. One is enhanced for CAT and second USB is for other thinks, I have tried many combinations using one or the other and still no CW trough USB cable.
I been trying to avoid hurting somebody saying that other well known contest software provide capability of configuring CW trough USB cable and it works.
I was told by someone that "driver for Logger32 CW machine need to be updated".

SeventyThree(s).
On November 29, 2019 at 5:47 PM Vince Shirley < vince.g0orc@...> wrote:

At last - the voice of sanity.

Thanks Darren.  I said in the early days of this thread that the menu item relates to the keying of the radio and not sending CW which was something I worked out when I briefly owned an FTdx3000 which was very similar.in this respect. 

I gave up because no-one was listening.

There is nothing in the manual to say that CW may be sent down the radio's USB port.  If some operators have got it work then you are better than me and I'd love to know how you have done it using CW machine in Logger32.

I failed to get it to work with the FTdx3000 which had essentially the same menu item at the FTdx101.   If I remember correctly the FTdx5000 had PC keying in the menu but it had not been activated and was waiting for a software update.

I'll go and have lie down now...

Regards

Vince G0ORC





On Fri, 29 Nov 2019 at 14:10, Darren Collins (G0TSM) < daz@...> wrote:

I don't own an FTDX101 (I have the FTDX5K) but looking at the user manual it suggests that PC KEYING relates to the PTT and not to the CW Keying. If you look at the settings for the other modes it has the same options but for the other modes says its for RPTT SELECT. So it appears to be badly worded.

[RTTY] RPTT SELECT - DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 90))

[CW] PC KEYING -  DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 94))

I would imagine that Yaesu would be able to implement CW Keying via a software update, so its just down to the FTDX101 owners to request the feature. I recall that someone at Yaesu USA ran a 'wish list' for the FTDX5000 when it came out, so they are probably doing the same for the 101.

73 Darren G0TSM



On 28/11/19 21:10, Andy None via Groups.Io wrote:
Vince
Same here. radio keys and unkeys but no CW is send.
I give up also and went by using WinKeyer USB.
Been trying to use enhanced or regular USB port (they have different COM number) without success.

Andy SP9KR

On Thursday, November 28, 2019, 5:25:01 p.m. GMT+1, Vince Shirley <vince.g0orc@...> wrote:



I give up with this - there is nothing in the manual save for an entry in the CW MENU section which describes how to key the radio via its own USP port.

The radio keys and unkeys OK - but no CW is sent

My last word on the subject.

Vince G0ORC


On Thu, 28 Nov 2019 at 16:04, Vince Shirley via Groups.Io <vince.g0orc= gmail.com@groups.io> wrote:
Yes Mike, quite so.

But it doesn't work! 

Did you not read the rest of the message?

Vince

On Thu, 28 Nov 2019 at 15:29, Mike < ch25@...> wrote:
On Thu, Nov 28, 2019 at 03:59 PM, Vince Shirley wrote:
Thank you - I'm quite prepared to eat a large portion of humble pie and admit that I was wrong, but I just can't get it this to work. 
As written in the manual.
Mike

 

 


 

 

 


 

 


ODP: ODP: [hamlogger] CW machine

Andy VA3PL
 

Hi Bob
I am not computer wiz, just the computer user.
These are com ports created by YAESU provided driver. It is Silicon Labs driver.

Silicon Labs Dual CT2105 USB UART Bridge Enhanced COM Port (in my case COM5 used for CAT)
Silicon Labs Dual CT2105 USB UART Bridge Standard COM Port (in my case COM6 used for CW, Audio, RTTY)

Andy SP9KR




Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Bob <k4cy@...>
Wysłane: niedziela, 1 grudnia 2019 16:28
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: ODP: [hamlogger] CW machine
 
What is an enhanced virtual port, and how/why is it necessary for your PC to CAT connection? 73.

On November 30, 2019 at 3:20 AM Andy VA3PL <va3pl@...> wrote:

 
Vince
Go to page 94 and read it and understand.

As a test just loaded N1MM set it up using ENHANCED virtual port for CAT and configured REGULAR virtual port for CW and it work nicely.

Also on 101D go to CW SETTING and change there to PC KEYING using DTR.

CW work nicely in N1MM but not using Logger32 CW MACHINE.

Andy SP9KR

Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Vince Shirley <vince.g0orc@...>
Wysłane: sobota, 30 listopada 2019 00:29
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: [hamlogger] CW machine
 
Hi Bob,

I still standby what I say in that there is nothing in the manual to suggest that CW may be sent down the USB port and I have never managed to make it work. I use an external interface should I wish to use electronic keying of CW

RTTY is supported as shown on P66 of the manual.  There is no such entry for CW.

The one thing that enables us to sleep soundly in our beds is that we don't have guns available to buy from our local supermarkets.  Oh, and our politicians may be the least respected members of our society but at least we haven't got Mr. Trump.  For that we are eternally grateful.

Vince 

On Fri, 29 Nov 2019 at 23:07, Bob < k4cy@...> wrote:
Vince, before you drift off into the arms of Morpheus (then wake up screaming from your nightmare of being on London Bridge at the wrong time) ... remember this message from the originator of the thread ...

Yes, there are two USB ports. One is enhanced for CAT and second USB is for other thinks, I have tried many combinations using one or the other and still no CW trough USB cable.
I been trying to avoid hurting somebody saying that other well known contest software provide capability of configuring CW trough USB cable and it works.
I was told by someone that "driver for Logger32 CW machine need to be updated".

SeventyThree(s).
On November 29, 2019 at 5:47 PM Vince Shirley < vince.g0orc@...> wrote:

At last - the voice of sanity.

Thanks Darren.  I said in the early days of this thread that the menu item relates to the keying of the radio and not sending CW which was something I worked out when I briefly owned an FTdx3000 which was very similar.in this respect. 

I gave up because no-one was listening.

There is nothing in the manual to say that CW may be sent down the radio's USB port.  If some operators have got it work then you are better than me and I'd love to know how you have done it using CW machine in Logger32.

I failed to get it to work with the FTdx3000 which had essentially the same menu item at the FTdx101.   If I remember correctly the FTdx5000 had PC keying in the menu but it had not been activated and was waiting for a software update.

I'll go and have lie down now...

Regards

Vince G0ORC





On Fri, 29 Nov 2019 at 14:10, Darren Collins (G0TSM) < daz@...> wrote:

I don't own an FTDX101 (I have the FTDX5K) but looking at the user manual it suggests that PC KEYING relates to the PTT and not to the CW Keying. If you look at the settings for the other modes it has the same options but for the other modes says its for RPTT SELECT. So it appears to be badly worded.

[RTTY] RPTT SELECT - DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 90))

[CW] PC KEYING -  DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 94))

I would imagine that Yaesu would be able to implement CW Keying via a software update, so its just down to the FTDX101 owners to request the feature. I recall that someone at Yaesu USA ran a 'wish list' for the FTDX5000 when it came out, so they are probably doing the same for the 101.

73 Darren G0TSM



On 28/11/19 21:10, Andy None via Groups.Io wrote:
Vince
Same here. radio keys and unkeys but no CW is send.
I give up also and went by using WinKeyer USB.
Been trying to use enhanced or regular USB port (they have different COM number) without success.

Andy SP9KR

On Thursday, November 28, 2019, 5:25:01 p.m. GMT+1, Vince Shirley <vince.g0orc@...> wrote:



I give up with this - there is nothing in the manual save for an entry in the CW MENU section which describes how to key the radio via its own USP port.

The radio keys and unkeys OK - but no CW is sent

My last word on the subject.

Vince G0ORC


On Thu, 28 Nov 2019 at 16:04, Vince Shirley via Groups.Io <vince.g0orc= gmail.com@groups.io> wrote:
Yes Mike, quite so.

But it doesn't work! 

Did you not read the rest of the message?

Vince

On Thu, 28 Nov 2019 at 15:29, Mike < ch25@...> wrote:
On Thu, Nov 28, 2019 at 03:59 PM, Vince Shirley wrote:
Thank you - I'm quite prepared to eat a large portion of humble pie and admit that I was wrong, but I just can't get it this to work. 
As written in the manual.
Mike

 

 


 

 

 


 


trouble with dx spots window

Matthias Bellmann
 

Hi
i am using a new computer win 10 prof. as administrator.
Now i am trying to make logger32 3.50.402 work as it was before. 
There are several problems:
 
1. FT8 / WSJT
The trcvr does not respond to the sound card out signal. PTT works, wsjt is reveiving.
 
 
2. CW machine similar problem. PTT works, cw machine is keying,but cw signal is ignored by trcvr. Use COM1 (real serial) und com4 (USB). Always same result. Did test every possible combination in the cw machine keyer setup. There muzst be something i did not realize.
 
3. I am connected with telnet dx-cluster. It works fine. dx spots are displayed in the telnet window but dx spots windows remains empty. Only WWV announcement and ann messages are displayed. All blocking filter in are disabled. 
 
PLEASE NO ANSWER "read help file". I did read help for many hours and did try many settings, now i gave up.
 
Any answer well be appreciated.
 
 
 


Re: ODP: [hamlogger] CW machine

Bob
 

What is an enhanced virtual port, and how/why is it necessary for your PC to CAT connection? 73.

On November 30, 2019 at 3:20 AM Andy VA3PL <va3pl@...> wrote:

 
Vince
Go to page 94 and read it and understand.

As a test just loaded N1MM set it up using ENHANCED virtual port for CAT and configured REGULAR virtual port for CW and it work nicely.

Also on 101D go to CW SETTING and change there to PC KEYING using DTR.

CW work nicely in N1MM but not using Logger32 CW MACHINE.

Andy SP9KR

Od: hamlogger@groups.io <hamlogger@groups.io> w imieniu użytkownika Vince Shirley <vince.g0orc@...>
Wysłane: sobota, 30 listopada 2019 00:29
Do: hamlogger@groups.io <hamlogger@groups.io>
Temat: Re: [hamlogger] CW machine
 
Hi Bob,

I still standby what I say in that there is nothing in the manual to suggest that CW may be sent down the USB port and I have never managed to make it work. I use an external interface should I wish to use electronic keying of CW

RTTY is supported as shown on P66 of the manual.  There is no such entry for CW.

The one thing that enables us to sleep soundly in our beds is that we don't have guns available to buy from our local supermarkets.  Oh, and our politicians may be the least respected members of our society but at least we haven't got Mr. Trump.  For that we are eternally grateful.

Vince 

On Fri, 29 Nov 2019 at 23:07, Bob < k4cy@...> wrote:
Vince, before you drift off into the arms of Morpheus (then wake up screaming from your nightmare of being on London Bridge at the wrong time) ... remember this message from the originator of the thread ...

Yes, there are two USB ports. One is enhanced for CAT and second USB is for other thinks, I have tried many combinations using one or the other and still no CW trough USB cable.
I been trying to avoid hurting somebody saying that other well known contest software provide capability of configuring CW trough USB cable and it works.
I was told by someone that "driver for Logger32 CW machine need to be updated".

SeventyThree(s).
On November 29, 2019 at 5:47 PM Vince Shirley < vince.g0orc@...> wrote:

At last - the voice of sanity.

Thanks Darren.  I said in the early days of this thread that the menu item relates to the keying of the radio and not sending CW which was something I worked out when I briefly owned an FTdx3000 which was very similar.in this respect. 

I gave up because no-one was listening.

There is nothing in the manual to say that CW may be sent down the radio's USB port.  If some operators have got it work then you are better than me and I'd love to know how you have done it using CW machine in Logger32.

I failed to get it to work with the FTdx3000 which had essentially the same menu item at the FTdx101.   If I remember correctly the FTdx5000 had PC keying in the menu but it had not been activated and was waiting for a software update.

I'll go and have lie down now...

Regards

Vince G0ORC





On Fri, 29 Nov 2019 at 14:10, Darren Collins (G0TSM) < daz@...> wrote:

I don't own an FTDX101 (I have the FTDX5K) but looking at the user manual it suggests that PC KEYING relates to the PTT and not to the CW Keying. If you look at the settings for the other modes it has the same options but for the other modes says its for RPTT SELECT. So it appears to be badly worded.

[RTTY] RPTT SELECT - DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 90))

[CW] PC KEYING -  DAKY (Pin 3 on data jack - (which is PTT) / DTR / RTS (Page 94))

I would imagine that Yaesu would be able to implement CW Keying via a software update, so its just down to the FTDX101 owners to request the feature. I recall that someone at Yaesu USA ran a 'wish list' for the FTDX5000 when it came out, so they are probably doing the same for the 101.

73 Darren G0TSM



On 28/11/19 21:10, Andy None via Groups.Io wrote:
Vince
Same here. radio keys and unkeys but no CW is send.
I give up also and went by using WinKeyer USB.
Been trying to use enhanced or regular USB port (they have different COM number) without success.

Andy SP9KR

On Thursday, November 28, 2019, 5:25:01 p.m. GMT+1, Vince Shirley <vince.g0orc@...> wrote:



I give up with this - there is nothing in the manual save for an entry in the CW MENU section which describes how to key the radio via its own USP port.

The radio keys and unkeys OK - but no CW is sent

My last word on the subject.

Vince G0ORC


On Thu, 28 Nov 2019 at 16:04, Vince Shirley via Groups.Io <vince.g0orc= gmail.com@groups.io> wrote:
Yes Mike, quite so.

But it doesn't work! 

Did you not read the rest of the message?

Vince

On Thu, 28 Nov 2019 at 15:29, Mike < ch25@...> wrote:
On Thu, Nov 28, 2019 at 03:59 PM, Vince Shirley wrote:
Thank you - I'm quite prepared to eat a large portion of humble pie and admit that I was wrong, but I just can't get it this to work. 
As written in the manual.
Mike