1. hamlogger@groups.io
   Date   
Re: Logger 32 / CW Machine

Bob
 

... and Google wont tell me if the gizmo actually toggles PTT, so you'll need to experiment with that by turning on your VOX (if your radio can operate CW PTT that way). SeventyThree(s).

On 07/25/2020 8:48 AM Bob <k4cy@...> wrote:


... and Google tells me it uses RTS keying.

So, with the gizmo unplugged, open the CW Machine. Select Software keyer. Open the Keyer setup. List the serial ports Logger32 can see. Now Close the Keyer setup window and plug in the gizmo. Open the keyer setup window an list the serial ports again. See the new one? That's the port you want. Select it. Now check the dedicated serial port and and standard keying options. Click apply. SeventyThree(s).
On 07/25/2020 7:30 AM ja1nlx <ayoshida0205@...> wrote:


Mike

I think you need to select "Software mode" and select proper serial port in CW machine.
The serial port is created when the device is connected to PC.

73

On 2020/07/25 20:14, n3bud wrote:
I was trying to get CW Machine in Logger 32 to control a USB to CW device.   Device works fine with N1MM but I can't get it to work with Logger 32's CW Machine.   The device is a LD-C103 and simulates a serial port.  Any one have a solution?
Thanks,
Mike, N3BUD 
--
73 de aki
JA1NLX

Re: Logger 32 / CW Machine

Bob
 

... and Google tells me it uses RTS keying.

So, with the gizmo unplugged, open the CW Machine. Select Software keyer. Open the Keyer setup. List the serial ports Logger32 can see. Now Close the Keyer setup window and plug in the gizmo. Open the keyer setup window an list the serial ports again. See the new one? That's the port you want. Select it. Now check the dedicated serial port and and standard keying options. Click apply. SeventyThree(s).

On 07/25/2020 7:30 AM ja1nlx <ayoshida0205@...> wrote:


Mike

I think you need to select "Software mode" and select proper serial port in CW machine.
The serial port is created when the device is connected to PC.

73

On 2020/07/25 20:14, n3bud wrote:
I was trying to get CW Machine in Logger 32 to control a USB to CW device.   Device works fine with N1MM but I can't get it to work with Logger 32's CW Machine.   The device is a LD-C103 and simulates a serial port.  Any one have a solution?
Thanks,
Mike, N3BUD 
--
73 de aki
JA1NLX

Re: Logger 32 / CW Machine

ja1nlx
 

Mike

I think you need to select "Software mode" and select proper serial port in CW machine.
The serial port is created when the device is connected to PC.

73

On 2020/07/25 20:14, n3bud wrote:
I was trying to get CW Machine in Logger 32 to control a USB to CW device.   Device works fine with N1MM but I can't get it to work with Logger 32's CW Machine.   The device is a LD-C103 and simulates a serial port.  Any one have a solution?
Thanks,
Mike, N3BUD 
--
73 de aki
JA1NLX
Logger 32 / CW Machine

n3bud
 

I was trying to get CW Machine in Logger 32 to control a USB to CW device.   Device works fine with N1MM but I can't get it to work with Logger 32's CW Machine.   The device is a LD-C103 and simulates a serial port.  Any one have a solution?
Thanks,
Mike, N3BUD 
Re: Name missing in L32Lookups

Phill Morris (G6EES)
 

Pete

 

Perhaps you could do some tests when you get a moment (L32 + WSJT-X) and let me know if and when it stores the name etc

 

Thanks

 

Phill G6EES

 

From: hamlogger@groups.io <hamlogger@groups.io> On Behalf Of G4RRM Pete
Sent: 25 July 2020 10:17
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Thanks for the explanation Phil. I’m sure I have seen exactly the same behaviour with WSJTx, sometimes carrying over the Name / QTH info and other times not.

 

I’ll watch the thread for any pointers.

73

Pete

G4RRM



On 25 Jul 2020, at 10:01, Phill Morris (G6EES) <Phill.morris@...> wrote:



Pete

 

Yes, thats exactly the same problem (when using WSJT-X). Its only when WSJT-X automatically stores the QSO.

 

If i manually store a QSO,  by pressing enter key when in the L32 LogEntry window, then the name and QTH is stored in the logbook. But thats not the correct way to use WSJT-X and shouldn't be necessary.

 

Bob (L32 Guru) says that L32 only stores what WSJT-X passes to it (and WSJT-X doesn't give name) 

BUT.......

 

1. Some people report here that their L32/WSJT-X set up does store the name.

 

2. On some (rare) occasions, my setup also stores the name, without me operating or using L32/WSJT-X in any different way - Why?

 

Its all very strange. 

Its not the end of the world if course, especially as you can manually add the name etc to the log after the QSO is stored, but that is a LOT of QSOs to manually update, especially with the high QSO rate of WSJT-X 

 

I have tried both programs and prefer WSJT-X to JTDX. Both have their problems, so JTDX isn't any better from that point of view

 

Phill G6EES

 

 

 

 

-------- Original message --------

From: G4RRM Pete <pete@...>

Date: 25/07/2020 09:27 (GMT+00:00)

Subject: Re: [hamlogger] Name missing in L32Lookups

 

Hi Phil

 

I’m late to this thread, but curious of the answer.

 

I use JTDX and have it set to carry over Name & QTH from L32 (Using Ham QTH) and all works fine.

But if I use WSJT-x and L32 (I use this on VHF radio) nothing carries over from the Name / QTH info.                 

 

Is that the same issue you’re having?

 

73

Pete

G4RRM

 

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Phill Morris (G6EES)
Sent: 25 July 2020 08:58
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Steph

 

You say it is working normally again.

 

Do you use WSJT-X with Logger32?

 

If yes, is the name recorded in your L32 logbook when the QSO is automatically recorded by WSJT-X?

 

Phill G6EES

 

 

 

 

-------- Original message --------

From: "Steph, F5NZY" <f5nzy@...>

Date: 25/07/2020 08:52 (GMT+00:00)

Subject: Re: [hamlogger] Name missing in L32Lookups

 

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: Name missing in L32Lookups

G4RRM Pete
 

Thanks for the explanation Phil. I’m sure I have seen exactly the same behaviour with WSJTx, sometimes carrying over the Name / QTH info and other times not.

I’ll watch the thread for any pointers.

73
Pete
G4RRM

On 25 Jul 2020, at 10:01, Phill Morris (G6EES) <Phill.morris@...> wrote:


Pete

Yes, thats exactly the same problem (when using WSJT-X). Its only when WSJT-X automatically stores the QSO.

If i manually store a QSO,  by pressing enter key when in the L32 LogEntry window, then the name and QTH is stored in the logbook. But thats not the correct way to use WSJT-X and shouldn't be necessary.

Bob (L32 Guru) says that L32 only stores what WSJT-X passes to it (and WSJT-X doesn't give name) 
BUT.......

1. Some people report here that their L32/WSJT-X set up does store the name.

2. On some (rare) occasions, my setup also stores the name, without me operating or using L32/WSJT-X in any different way - Why?

Its all very strange. 
Its not the end of the world if course, especially as you can manually add the name etc to the log after the QSO is stored, but that is a LOT of QSOs to manually update, especially with the high QSO rate of WSJT-X 

I have tried both programs and prefer WSJT-X to JTDX. Both have their problems, so JTDX isn't any better from that point of view

Phill G6EES




-------- Original message --------
From: G4RRM Pete <pete@...>
Date: 25/07/2020 09:27 (GMT+00:00)
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

Hi Phil

 

I’m late to this thread, but curious of the answer.

 

I use JTDX and have it set to carry over Name & QTH from L32 (Using Ham QTH) and all works fine.

But if I use WSJT-x and L32 (I use this on VHF radio) nothing carries over from the Name / QTH info.                 

 

Is that the same issue you’re having?

 

73

Pete

G4RRM

 

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Phill Morris (G6EES)
Sent: 25 July 2020 08:58
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Steph

 

You say it is working normally again.

 

Do you use WSJT-X with Logger32?

 

If yes, is the name recorded in your L32 logbook when the QSO is automatically recorded by WSJT-X?

 

Phill G6EES

 

 

 

 

-------- Original message --------

From: "Steph, F5NZY" <f5nzy@...>

Date: 25/07/2020 08:52 (GMT+00:00)

Subject: Re: [hamlogger] Name missing in L32Lookups

 

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: Name missing in L32Lookups

Phill Morris (G6EES)
 

Pete

Yes, thats exactly the same problem (when using WSJT-X). Its only when WSJT-X automatically stores the QSO.

If i manually store a QSO,  by pressing enter key when in the L32 LogEntry window, then the name and QTH is stored in the logbook. But thats not the correct way to use WSJT-X and shouldn't be necessary.

Bob (L32 Guru) says that L32 only stores what WSJT-X passes to it (and WSJT-X doesn't give name) 
BUT.......

1. Some people report here that their L32/WSJT-X set up does store the name.

2. On some (rare) occasions, my setup also stores the name, without me operating or using L32/WSJT-X in any different way - Why?

Its all very strange. 
Its not the end of the world if course, especially as you can manually add the name etc to the log after the QSO is stored, but that is a LOT of QSOs to manually update, especially with the high QSO rate of WSJT-X 

I have tried both programs and prefer WSJT-X to JTDX. Both have their problems, so JTDX isn't any better from that point of view

Phill G6EES




-------- Original message --------
From: G4RRM Pete <pete@...>
Date: 25/07/2020 09:27 (GMT+00:00)
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

Hi Phil

 

I’m late to this thread, but curious of the answer.

 

I use JTDX and have it set to carry over Name & QTH from L32 (Using Ham QTH) and all works fine.

But if I use WSJT-x and L32 (I use this on VHF radio) nothing carries over from the Name / QTH info.                 

 

Is that the same issue you’re having?

 

73

Pete

G4RRM

 

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Phill Morris (G6EES)
Sent: 25 July 2020 08:58
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Steph

 

You say it is working normally again.

 

Do you use WSJT-X with Logger32?

 

If yes, is the name recorded in your L32 logbook when the QSO is automatically recorded by WSJT-X?

 

Phill G6EES

 

 

 

 

-------- Original message --------

From: "Steph, F5NZY" <f5nzy@...>

Date: 25/07/2020 08:52 (GMT+00:00)

Subject: Re: [hamlogger] Name missing in L32Lookups

 

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: Name missing in L32Lookups

G4RRM Pete
 

Hi Phil

 

I’m late to this thread, but curious of the answer.

 

I use JTDX and have it set to carry over Name & QTH from L32 (Using Ham QTH) and all works fine.

But if I use WSJT-x and L32 (I use this on VHF radio) nothing carries over from the Name / QTH info.                 

 

Is that the same issue you’re having?

 

73

Pete

G4RRM

 

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Phill Morris (G6EES)
Sent: 25 July 2020 08:58
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Steph

 

You say it is working normally again.

 

Do you use WSJT-X with Logger32?

 

If yes, is the name recorded in your L32 logbook when the QSO is automatically recorded by WSJT-X?

 

Phill G6EES

 

 

 

 

-------- Original message --------

From: "Steph, F5NZY" <f5nzy@...>

Date: 25/07/2020 08:52 (GMT+00:00)

Subject: Re: [hamlogger] Name missing in L32Lookups

 

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: Name missing in L32Lookups

Phill Morris (G6EES)
 

Steph

You say it is working normally again.

Do you use WSJT-X with Logger32?

If yes, is the name recorded in your L32 logbook when the QSO is automatically recorded by WSJT-X?

Phill G6EES




-------- Original message --------
From: "Steph, F5NZY" <f5nzy@...>
Date: 25/07/2020 08:52 (GMT+00:00)
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)

Re: Name missing in L32Lookups

Steph, F5NZY
 

Thanks to Rick, everything is working normally again.

I downloaded the L32LookupInstall.msi file from Rick's site.

http://www.n2amg.com/software/l32lookups-for-logger32/

73 de Steph, F5NZY

--
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: L32Lookup's name...

Rick Ellison
 

Hi Steph..

Go to my website and download the latest version. I posted it last week to correct a change that QRZ made to the page format. It might ask you to uninstall the current version first. It has done that on a couple of systems I have been told..

 

73 Rick N2AMG

 

From: Steph, F5NZY [mailto:f5nzy@...]
Sent: Friday, July 24, 2020 12:13 PM
To: Rick Ellison <rellison@...>
Subject: L32Lookup's name...

 

Hi Rick,

Here is what I can report :

When ckecked QRZ HTTP your name does not appearin the L32Lookup.

It does with QRZ XML.

73 de Steph, F5NZY



-- 
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)

Virus-free. www.avast.com

Re: Name missing in L32Lookups

Steph, F5NZY
 

Hi Phill and all,

Here is what I sent to Rick.

73 de Steph, F5NZY

.../...

Hi Rick,

Here is what I can report :

When ckecked QRZ HTTP your name does not appear in the L32Lookup.

It does with QRZ XML.

73 de Steph, F5NZY



-- 
-- 
Everything looks impossible to the people who never tried anything.
(Dr J-L Etienne)
Re: seem a bug previous QSO

F4FQH Olivier
 

OULLAAAAAAAA !!!
 
Sorry Bob !!! Sourire yes i’m hallucinating...
Too much tired..
It’s in W/C windows that open another windows with all QSO !!....
I confirm...no beers no chateauneuf du pape !!! Sourire just tired
 
Sorry for the messages.
 
73
Olivier
F4FQH
 

From: Bob
Sent: Thursday, July 23, 2020 11:30 AM
To: hamlogger@groups.io ; F4FQH Olivier
Subject: Re: [hamlogger] seem a bug previous QSO
 
Oliver, I think you are hallucinating. You are already in the Previous QSOs window where you can see all QSOs with the station. Why open another window to see all the QSOs? SeventyThree(s).
On 07/23/2020 5:10 AM F4FQH Olivier <unit365@...> wrote:
 
 
Hi Bob and all
 
Seem there is a bug or deleted function in the previous QSO windows
 
Before, when we clicked on a QSO, another log windows opened with all QSO.
Now when i click, there is nothing that open.
 
Checked on a 2nd logger and it’s the same issue.
or i missed something
 
Thanks
 
73s
 
Olivier
F4FQH
 
 
 

Re: seem a bug previous QSO

Bob
 

Oliver, I think you are hallucinating. You are already in the Previous QSOs window where you can see all QSOs with the station. Why open another window to see all the QSOs? SeventyThree(s).

On 07/23/2020 5:10 AM F4FQH Olivier <unit365@...> wrote:


Hi Bob and all

Seem there is a bug or deleted function in the previous QSO windows

Before, when we clicked on a QSO, another log windows opened with all QSO.
Now when i click, there is nothing that open.

Checked on a 2nd logger and it’s the same issue.
or i missed something

Thanks

73s

Olivier
F4FQH


 

seem a bug previous QSO

F4FQH Olivier
 

Hi Bob and all
 
Seem there is a bug or deleted function in the previous QSO windows
 
Before, when we clicked on a QSO, another log windows opened with all QSO.
Now when i click, there is nothing that open.
 
Checked on a 2nd logger and it’s the same issue.
or i missed something
 
Thanks
 
73s
 
Olivier
F4FQH
 
 
Re: Name missing in L32Lookups

Bob
 

Rick, those were my observations (maybe a year ago). Today, I have no idea. Apparently others see different results. C'set la vie. Que sera, sera. SeventyThree(s).

On 07/20/2020 8:45 PM Rick Ellison <rellison@...> wrote:


For me in JTDX the name works but in WSJT the name is not working for me.. I have tried transferring the First name only or First and Last but it still does not get transferred..

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Damian M0BKV via groups.io
Sent: Monday, July 20, 2020 6:30 PM
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups


Yes Bob mine is working fine. Its just my brain is a bit dodgy tonight. 73



Virus-free. www.avast.com

Re: Name missing in L32Lookups

Rick Ellison
 

For me in JTDX the name works but in WSJT the name is not working for me.. I have tried transferring the First name only or First and Last but it still does not get transferred..

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Damian M0BKV via groups.io
Sent: Monday, July 20, 2020 6:30 PM
To: hamlogger@groups.io
Subject: Re: [hamlogger] Name missing in L32Lookups

 

Yes Bob mine is working fine. Its just my brain is a bit dodgy tonight. 73


Virus-free. www.avast.com

Re: Name missing in L32Lookups

Bob
 

Damian, a word of advice from the 'Colonies' ... Just say, "I rebooted, and it's working again". SeventyThree(s).

On 07/20/2020 6:29 PM Damian M0BKV via groups.io <damianm0bkv@...> wrote:


Yes Bob mine is working fine. Its just my brain is a bit dodgy tonight. 73

Re: Name missing in L32Lookups

Damian M0BKV
 

Yes Bob mine is working fine. Its just my brain is a bit dodgy tonight. 73
Re: Name missing in L32Lookups

Bob
 

I'll take that as notification that WSJT no longer drops TxEnable prematurely. Thanks, SeventyThree(s).

On 07/20/2020 6:10 PM Damian M0BKV via groups.io <damianm0bkv@...> wrote:


I've been using WSJT-w all day on varies bands and the name is transferred every time. Phil I use the 'Transfer First Name' otherwise the picture is as Bobs Fields to transfer picture. Make sure the program Creation Date for the L32Lookups application  in the L32Lookups folder is 20/07/2020.
My problem earlier was I had changed something stupid earlier this evening.
Damian

2221 - 2240 of 82993