Date   
Re: JTDX

John Owens
 

Thanks to all that responded to my request for help on JTDX. I have resolved the problem I call about, and thanks to those who responded.

John Owens -  N7TK
 


Re: L32 and SDR Console

Bob
 

That's correct ... Both radios can set the frequency/mode ... As a precaution, after one radio has sent a command to the other, it ignores the next incoming message ... becaue it might have been sent before the command was issued if that was the case, then all hell would break loose and the radios would jump from one freq/mode to the other endlessly ... 73.

On February 13, 2020 at 1:54 PM Jim Cox <jcox123@...> wrote:

Well spoke too soon Bob.. Now getting this one the slave port debug screen “I’m busy, poll reply ignored”   Jim
 
 
From: Bob
Sent: Thursday, February 13, 2020 11:28 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console
 
Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).
 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 


 



 

 

 

Re: L32 and SDR Console

Bob
 

Jim, funny how the simple things are often the most difficult to grasp :)  Please test the scenario I described to Rick ... Run WSJT/JTDX and no CAT between Logger32 and the main radio. On the UDP BandMap click CONFIG and check the option to ALLOW WSJT/JTDX TO SET LOGGER32 FREQUENCY/MODE. Now, change Band and/or Mode of WSJT/DX. Does the slave radio follow? If not, look at the Slave Radio Debug Window. Do you see commands from Logger32 to change frequency/mode?

I avoid all the nonsense and use a radio without CAT. Works fine, lasts a long time. And, I have yet to hear of a single case where the QSO could not have been completed without an SDR and an ultra high def 4K display. SeventyThree(s).

On February 13, 2020 at 1:49 PM Jim Cox <jcox123@...> wrote:

Bob, I have been struggling with similar circumstances with trying to get SDRUno (panadapter program) to work with Logger32 and JTDX and not having any luck with various combos..
Tried this morning with the Slave port and it seems to work fine.  I did have to create a virtual serial cable 12 to 13 and used 12 for the slave port and 13 for the sdruno program using Kenwood emulation.  Working fine now but let me use it today and see if works ok with various combinations, etc.  I tried to just assign a virtual port to the Slave port and use that same port for the panadapter program but no luck that way.  73s Jim K4JAF
 
From: Bob
Sent: Thursday, February 13, 2020 11:28 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console
 
Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).
 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 


 



 

 

 

Re: L32 and SDR Console

Jim Cox
 

Well working again Bob..  Seems to freeze occasionally ---- will keep playing with it..   73s Jim K4JAF
 
 

From: Jim Cox
Sent: Thursday, February 13, 2020 12:54 PM
To: hamlogger@groups.io
Subject: Re: [hamlogger] L32 and SDR Console
 
Well spoke too soon Bob.. Now getting this one the slave port debug screen “I’m busy, poll reply ignored”   Jim
 
From: Bob
Sent: Thursday, February 13, 2020 11:28 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console
 
Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).
 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 


 



 

 

Re: L32 and SDR Console

Jim Cox
 

Well spoke too soon Bob.. Now getting this one the slave port debug screen “I’m busy, poll reply ignored”   Jim
 

From: Bob
Sent: Thursday, February 13, 2020 11:28 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console
 
Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).
 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 


 



 

 

Re: L32 and SDR Console

Jim Cox
 

Bob, I have been struggling with similar circumstances with trying to get SDRUno (panadapter program) to work with Logger32 and JTDX and not having any luck with various combos..
Tried this morning with the Slave port and it seems to work fine.  I did have to create a virtual serial cable 12 to 13 and used 12 for the slave port and 13 for the sdruno program using Kenwood emulation.  Working fine now but let me use it today and see if works ok with various combinations, etc.  I tried to just assign a virtual port to the Slave port and use that same port for the panadapter program but no luck that way.  73s Jim K4JAF
 

From: Bob
Sent: Thursday, February 13, 2020 11:28 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console
 
Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).
 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 


 



 

 

Re: Macros K3/K3S

Jacek Marczewski
 

Thanks Bob for prompt answer. It works now.

73 de Jacek SP5EAQ

I don't have a K3, so I can't test, but you probably need to setup a macro like this  $command SWH16;$ to turn TUNE on, and you will probably need another one to turn tune off *whatever the SWH number is).  If that's what you have, and it doesn't work, then someone with a K3 will have to help. SeventyThree(s).
On February 13, 2020 at 12:08 PM Jacek Marczewski <jmarcz@...> wrote:

Just a question: macro SWH16;  tested in K3 Utility works perfectly (activates TUNE emulating holding  button)
but written into macro setup window of Radio Control Panel of Logger 32 does not work (radio continues read  VFO frequency as usual and nothing happens).
I am a newcomer in macros, sri for bothering you with such a basic  question.
Maybe I should write to the window of control panel something more than SWH16;  to send the command while clicking
(or configure anything else to allow control panel to send  a command to K3)?
73 de Jacek SP5EAQ

 

Re: 4RE: [hamlogger] L32 and SDR Console

Rick Ellison
 

Ok I will try this a bit later have to go spend some more $$ with the wife..

73

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 12:28 PM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).

 

On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.

On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 

 

 


 


 

Re: Macros K3/K3S

Bob
 

I don't have a K3, so I can't test, but you probably need to setup a macro like this  $command SWH16;$ to turn TUNE on, and you will probably need another one to turn tune off *whatever the SWH number is).  If that's what you have, and it doesn't work, then someone with a K3 will have to help. SeventyThree(s).

On February 13, 2020 at 12:08 PM Jacek Marczewski <jmarcz@...> wrote:

Just a question: macro SWH16;  tested in K3 Utility works perfectly (activates TUNE emulating holding  button)
but written into macro setup window of Radio Control Panel of Logger 32 does not work (radio continues read  VFO frequency as usual and nothing happens).
I am a newcomer in macros, sri for bothering you with such a basic  question.
Maybe I should write to the window of control panel something more than SWH16;  to send the command while clicking
(or configure anything else to allow control panel to send  a command to K3)?
73 de Jacek SP5EAQ

 

Re: 4RE: [hamlogger] L32 and SDR Console

Bob
 

Rick, it's already working, guess I already coded for it. When Logger32 relinquishes radio control to WSJT/JTDX, Logger32 takes the WSJT/JTDX frequency from the UDP StatusOut message constructs a set frequency/mode message in the appropriate slave radio format and sends it. So, your ultra high def eye candy machine should still follow the radio as you snag those rare and exotic 77 byte (or whatever they are) QSOs. Give it a whirl. The attached picture is what was sent to the slave when I changed JTDX from FT8 to FT4 (no Logger32 CAT control connected). SeventyThree(s).


On February 13, 2020 at 11:46 AM Bob <k4cy@...> wrote:

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.
On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 

 



 

 

Re: JTDX

Bob
 

I's recommend you go here:  https://www.jtdx.tech/en/10-main-page  At the right side of the page are all the full install packages.  Pick the one you need, and install it. SeventyThree(s).

On February 13, 2020 at 11:59 AM John Owens <jcowens1@...> wrote:

Had to download a new JTDX file (.exe) and it is now sitting in my Desktop. Need  to know where this executable file for JTDX needs to be located for it to be accessed when I invoke UDP in L32. Help would be appreciated.

Thanks 

 John Owens -  N7TK
 



 

Macros K3/K3S

Jacek Marczewski
 

Just a question: macro SWH16;  tested in K3 Utility works perfectly (activates TUNE emulating holding  button)
but written into macro setup window of Radio Control Panel of Logger 32 does not work (radio continues read  VFO frequency as usual and nothing happens).
I am a newcomer in macros, sri for bothering you with such a basic  question.
Maybe I should write to the window of control panel something more than SWH16;  to send the command while clicking
(or configure anything else to allow control panel to send  a command to K3)?
73 de Jacek SP5EAQ

Re: JTDX

Dave Colliau
 

In the JTDX folder.
Dave N8DC

On February 13, 2020 at 11:59 AM John Owens <jcowens1@...> wrote:

Had to download a new JTDX file (.exe) and it is now sitting in my Desktop. Need  to know where this executable file for JTDX needs to be located for it to be accessed when I invoke UDP in L32. Help would be appreciated.

Thanks 

 John Owens -  N7TK
 



 

JTDX

John Owens
 

Had to download a new JTDX file (.exe) and it is now sitting in my Desktop. Need  to know where this executable file for JTDX needs to be located for it to be accessed when I invoke UDP in L32. Help would be appreciated.

Thanks 

 John Owens -  N7TK
 


Re: 4RE: [hamlogger] L32 and SDR Console

Bob
 

I'm investigating a fix for that ... Take the Frequency sent over the UDP, generate/format a CAT frequency command message and send it to the slave port ... 73.

On February 13, 2020 at 11:29 AM Rick Ellison <rellison@...> wrote:

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 

 



 

Re: 4RE: [hamlogger] L32 and SDR Console

Rick Ellison
 

I just don’t use SDRC if I am going to do WSJT. Since Logger32 closes the CAT port to WSJT the information would not be sent over to SDRC or SDRUno.

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 8:00 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

... now how do you handle WSJT/JTDX into the mix? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 

Re: 4RE: [hamlogger] L32 and SDR Console

Rick Ellison
 

One thing that I did not mention is this same setup can also be used with SRDUno. You just need to enable the CAT port settings in the program and tell it what port to listen for the commands.

Not me doing any youtube videos. I have no camera setup here..

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Bob
Sent: Thursday, February 13, 2020 7:56 AM
To: hamlogger@groups.io
Subject: Re: 4RE: [hamlogger] L32 and SDR Console

 

Thanks for the detailed description Rick. Simplicity itself (even I could understand it). This is an open request to all subscribers - How about a  YouTube video describing how to do this. Time to debunk the folklore and voodoo surrounding Logger32 and Omnirig. Yes, Omnirig and Logger32 do play together, but is it really necessary? SeventyThree(s).

On February 13, 2020 at 2:14 AM Rick Ellison <rellison@...> wrote:

Hi Chuck..

Sorry for not responding sooner I had to set things back up so I could get the settings for you as I haven’t turned on my radio in about a month..

I’m using a 7300 and one virtual serial port.

 

1.       Open VSPE and create one virtual port in VSPE its called a connector. This is set to COM13.

2.       Load Logger32. In Logger32 I have the 7300 connected and Logger32 has full radio control over the radio

3.       Click on setup and then go to the radio setup window and select Slave Configuration. This is how my slave window is setup.

 

Note that I have COM13 the VSPE port set as the com port.

 

4.       Now open SDR Console and open up the options. In the options window you will want to click on Controllers and then CAT then port selection. Your Virtual port should be shown in the listing of ports available select it by placing a checkmark in the box. (If you want to make sure things are working correctly you can open the I/O Monitor and you should see the radio commands going by if they are connected.

 

After closing the options window the frequency in SDRC’s frequency display should show that of your radio in Logger32. This is a two-way connection. If you change the frequency in Logger32 the frequency should update in SDRC. If you change the frequency or mode in SDRC then Logger32 should update also.

Here is an image of my using SDRC within Logger32. I have an SDR-Play RSP1 connected to my computer that SDRC is getting its information from..

 

 

 

73 Rick N2AMG

 

From: hamlogger@groups.io [mailto:hamlogger@groups.io] On Behalf Of Chuck Miller
Sent: Tuesday, February 11, 2020 4:35 PM
To: hamlogger@groups.io
Subject: [hamlogger] L32 and SDR Console

 

How do I get L32 and SDR Console to talk to my FT-1000mp Mk V Field?
Logger32 does not work with Omnirig, but SDR Console seems to require it. SDR Console says use TS-2000 protocol, but logger32 does not have a selection for the TS-2000. Tried using VSPE, but no joy.

73, Chuck
N0NC

 

 


 

Re: When callsign is in EW

Andy None
 

Thanks a lot, Bob
Do not forgot to add <ESC> to DVK.
Also would be nice to have ability of multiple pressing keys to send let say twice (or more times) my call.

Andy SP9KR your follower.

On Thursday, February 13, 2020, 3:44:39 p.m. GMT+1, Bob <k4cy@...> wrote:


On the UDP BandMap, click CONFIG | LOGGING OPTIONS and UNcheck the LOG ADDITIONAL INFO FROM LOGBOOK ENTRY WINDOWS. SeventyThree(s).
On February 13, 2020 at 9:20 AM "Andy None via Groups.Io" <va3pl@...> wrote:

When some call sign is in Entry Window with populated name and QTH fields and I work someone else on FT8 and auto-log that QSO name and QTH from other QSO is being wrongly copied to new QSO.

Seventy Three

Andy SP9KR


 

Re: When callsign is in EW

Bob
 

On the UDP BandMap, click CONFIG | LOGGING OPTIONS and UNcheck the LOG ADDITIONAL INFO FROM LOGBOOK ENTRY WINDOWS. SeventyThree(s).

On February 13, 2020 at 9:20 AM "Andy None via Groups.Io" <va3pl@...> wrote:

When some call sign is in Entry Window with populated name and QTH fields and I work someone else on FT8 and auto-log that QSO name and QTH from other QSO is being wrongly copied to new QSO.

Seventy Three

Andy SP9KR


 

When callsign is in EW

Andy None
 

When some call sign is in Entry Window with populated name and QTH fields and I work someone else on FT8 and auto-log that QSO name and QTH from other QSO is being wrongly copied to new QSO.

Seventy Three

Andy SP9KR