Now you know why no DXCC information is being logged. Logger32 doesn't know where you are. Click SETUP | UPDATES | COUNTRY DATABASE EXCEPTIONS FROM CLUB LOG | LOOK FOR UPDATES NOW. When updates have finished downloading/installing, try entering DK4WD id the Logbook Entry Window again. Does Logger32 know you are in Germany now? SeventyThree(s).

On January 2, 2020 at 11:17 AM Matthias Bellmann <Dk4wd@...> wrote:

instead of dl eu14 it shows "** ?? ??"

Am 02.01.2020 um 17:05 schrieb Bob:

... and if you type DK4WD in the Logbook Entry Window, what Country does Logger32 say that is? 73.

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias

 

 

On January 2, 2020 at 2:48 PM Svein Henriksen <la3pu@...> wrote:

Hi all,

 

In UDP Bandmap Configuration there is an option to set up e-mail / SMS message.

However, I do not seem to be able to find where to set the telephone number to send SMS to.

I cannot find it in the help file and have looked in all the settings....I think.

Any assistance would be appreciated.

 

73 de LA3PU

On January 2, 2020 at 2:48 PM Svein Henriksen <la3pu@...> wrote:

Hi all,

 

In UDP Bandmap Configuration there is an option to set up e-mail / SMS message.

However, I do not seem to be able to find where to set the telephone number to send SMS to.

I cannot find it in the help file and have looked in all the settings....I think.

Any assistance would be appreciated.

 

73 de LA3PU

On January 2, 2020 at 2:48 PM Svein Henriksen <la3pu@...> wrote:

Hi all,

 

In UDP Bandmap Configuration there is an option to set up e-mail / SMS message.

However, I do not seem to be able to find where to set the telephone number to send SMS to.

I cannot find it in the help file and have looked in all the settings....I think.

Any assistance would be appreciated.

 

73 de LA3PU

On January 2, 2020 at 12:38 PM Andy VA3PL <va3pl@...> wrote:

When working split transmitting frequency is recorded.

Is there somewhere setting that receiving frequency will be recorded.

Andy SP9KR

On January 2, 2020 at 12:38 PM Andy VA3PL <va3pl@...> wrote:

When working split transmitting frequency is recorded.

Is there somewhere setting that receiving frequency will be recorded.

Andy SP9KR

On January 2, 2020 at 11:17 AM Matthias Bellmann <Dk4wd@...> wrote:

instead of dl eu14 it shows "** ?? ??"

Am 02.01.2020 um 17:05 schrieb Bob:

... and if you type DK4WD in the Logbook Entry Window, what Country does Logger32 say that is? 73.

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias

 

... and if you type DK4WD in the Logbook Entry Window, what Country does Logger32 say that is? 73.

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias

On January 2, 2020 at 11:02 AM Kenneth Hansen <khansen@...> wrote:

Germany only

On Thu, Jan 2, 2020 at 11:01 AM Bob < k4cy@...> wrote:

... and if you type DK4WD in the Logbook Entry Window, what Country does Logger32 say that is? 73.

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias

 

 

 

--

Kenneth Hansen

Owner

ScanAm Technical Services, LLC

On January 2, 2020 at 10:59 AM Kenneth Hansen <khansen@...> wrote:

Just tried to import the same file on a Win7 laptop running Logger32 as Administrator, same error message

On Thu, Jan 2, 2020 at 10:27 AM Bob < k4cy@...> wrote:

Ken, Running as Administrator an running a program (in this case Logger32) are two different things. You must run Logger32 as an Administrator ... like this: Right click on the Logger32.exe icon, click properties. Select the compatibility tab and set the option to run Logger32 as an administrator.

The Jan2020 file is an ADIF formatted file? Are there security settings on your laptop that are preventing you from opening Jan2020.adif, or writing to the logbook? SeventyThree(s).

On January 2, 2020 at 10:10 AM Kenneth Hansen < khansen@...> wrote:

Yes I’m running as Administrator

I just named the export fine Jan2020

On Thu, Jan 2, 2020 at 10:01 AM Bob < k4cy@...> wrote:

Ken, you are running Logger32 on the laptop with Admin Privileges. Right? What is the file name you are trying to open/import on the laptop? SeventyThree(s).

On January 2, 2020 at 9:29 AM Kenneth Hansen < khansen@...> wrote:

Happy New Year

I am trying to update my logbook on my laptop running Win10

I used Export Log on the desktop running Win7

Logger32 version on both computers are 3.50.403

Importing the logbook on the laptop gives me Run-time error 52.  Bad file name or number.

Clicking on OK closes Logger32.

Any help will be Appreciated

de KB2SSE- Ken

--

Kenneth Hansen

Owner

ScanAm Technical Services, LLC

 

 

 

 

--

Kenneth Hansen

Owner

ScanAm Technical Services, LLC

 

 

 

 

--

Kenneth Hansen

Owner

ScanAm Technical Services, LLC

On January 2, 2020 at 10:41 AM Matthias Bellmann < Dk4wd@...> wrote:

I enter my qso in the (normal ?) way into the nput window. Usually cw,

but sometimes ft8 and ssb. by pressing the enter key the just logged

qsdo is transferred into logbool page, but dxcc column contains "not

accepted". When a former qso with the station is alread logged the dxcc

is displayed correctly.

Am 02.01.2020 um 16:05 schrieb Bob:

So, how are you entering the QSO in the logbook, What mode are you operating? SeventyThree(s).

On January 2, 2020 at 9:51 AM Matthias Bellmann < Dk4wd@...> wrote:

When qsoing a new statioin the dxcc column in the logbook page remains

empty. This column is filled only after using updates menue. This is

pretty inconvenient, because the worked/confirmed window also remains

empty. So when i qso a new station i can not check whether the

appropriate country is already in my log.

I remember that in former versions of logger32 there has been a

dxcc-table. Is it still available or must i carry out the above

mentioned update?

By the way: Happy new year to all of you

73 Matthias