Date   
Re: Heil Headset / Mic Settings

Gerry VE6LB
 


The Heil website gives you thee settings.

Gerry VE6LB

On 2019-11-03 19:26, k4cvl wrote:

I plan to use a Heil PROSET with the HC-5 element. I’d appreciate any head start on the EQ and other settings to apply to my MP model.  Thanks in advance.

-Mike, K4CVL


-- 
73, Gerry VE6LB
ve6lb@...
ve6lb.ve6hams.com

Odg: [hamlogger] LOTW files export

gabor.s57wj@gmail.com
 

Hello, 
I had the same problem yesterday. 
By the LoTW file export I can't find my callsign and I cannot export the file. 

73! Gabor, S57WJ 

Sent from Huawei mobile device. 


-------- Izvirno sporočilo --------
Zadeva: [hamlogger] LOTW files export
Od: sp5ewx
Za: hamlogger@groups.io
Kp:

Hello 
I'm using win 10 ..after 16 Oct I cant export files for LOTW ..Logger cant see my call sign on the operator list.Before 16th Oct everything was OK .Everything seems to be OK , ie "Send QSO to LOTW is checked .,the field of operator is correct .When I transfered this part of log into computer with Win7, problem dissapeared .I tried to change operator callsign for another one , system also  coudnt see the change.It happened after 16Oct QSOs...Any idea ??
Mike sp5ewx

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Vince, are you saying I need to do all that BS stuff (no pun intended) with the FT-101s, and not worry about sending actual antenna switching commands with set frequency commands from Logger32?  73

On November 4, 2019 at 10:58 AM Vince Shirley <vince.g0orc@...> wrote:

Bob,

What Darren has suggested is correct...

Vince

On Mon, 4 Nov 2019 at 13:31, Darren Collins (G0TSM) < daz@...> wrote:
When the FTDX5000 came out Bob corrected the same issue ( I think)
Logger32 needs to send the band command first and then the mode and frequency.

Sending the BS command will put the rig on the right band and the band stack registers select the antenna, ipo, att, etc. This should be immediately followed by the mode and freq. I think that’s right.

Sorry I’m away from the shack this week so can’t check at home, but I did have a glance through the pdf for the 101’s CAT commands, and it appears to be similar.

73 Darren G0TSM





On 4 Nov 2019, at 13:05, Bob < k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau < n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob < k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob < k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" < cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

 


 

Re: CAT Control of FTDX101 via Logger 32

Vince Shirley
 

Bob,

What Darren has suggested is correct...

Vince

On Mon, 4 Nov 2019 at 13:31, Darren Collins (G0TSM) <daz@...> wrote:
When the FTDX5000 came out Bob corrected the same issue ( I think)
Logger32 needs to send the band command first and then the mode and frequency.

Sending the BS command will put the rig on the right band and the band stack registers select the antenna, ipo, att, etc. This should be immediately followed by the mode and freq. I think that’s right.

Sorry I’m away from the shack this week so can’t check at home, but I did have a glance through the pdf for the 101’s CAT commands, and it appears to be similar.

73 Darren G0TSM





On 4 Nov 2019, at 13:05, Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

Re: LOTW files export

sp5ewx
 

Nobody encountered same problem???

sp5ewx

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Phil, Darren, I have mailed you a download link for the limited Guy Fawkes edition of Logger32. Minimal testing here ( sans TSF), but I see this when clicking on a DXSpot to change VFO-A (or whatever the correct terminology is). SeventyThree(s).


On November 4, 2019 at 8:47 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

All Greek to me Bob, and thanks to the others for pitching in with their thoughts and tech help.  If it makes any difference the default fall back antenna may be best being made Antenna 1 - for the multiband HF beam most of us use. If the radio coupled to an external device, such as a linear amp which stays turned off a lot of the time, generally the relay on the linear drops back to allow Antenna 1 connection on the linear to remain connected straight through with the power to the linear switched off.  Antenna 3 is selectable on the 101 series as a receive antenna only via the menu, although few of us have that luxury, so not as important to my mind as having 3 antenna connections which one can transmit into on different bands. 

73 Phil  

 

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Pete, bite your tongue. 

73(s) de K4CY/G4ECD.

On November 4, 2019 at 8:57 AM n5kd <n5kd@...> wrote:

Bob, I know you have always said OmniRig would be added over your dead body (I’m paraphrasing).

Please, Maybe you would consider a little softening of this stance at some time.

Thanks.

73’ Pete, N5KD / G4DVP.

Sent from my mobile

On Nov 4, 2019, at 08:11, Bob < k4cy@...> wrote:

Dave, could it be that you can set the radio to operate cross band, when doing this the antenna selected when transmitting may be different to the one for receiving. Do I really want to get in the middle of this? SeventyThree(s).
On November 4, 2019 at 8:05 AM Bob < k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau < n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob < k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob < k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" < cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

n5kd
 

Bob, I know you have always said OmniRig would be added over your dead body (I’m paraphrasing).

Please, Maybe you would consider a little softening of this stance at some time.

Thanks.

73’ Pete, N5KD / G4DVP.

Sent from my mobile

On Nov 4, 2019, at 08:11, Bob <k4cy@...> wrote:

Dave, could it be that you can set the radio to operate cross band, when doing this the antenna selected when transmitting may be different to the one for receiving. Do I really want to get in the middle of this? SeventyThree(s).
On November 4, 2019 at 8:05 AM Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Philip (G4OBK) Catterall
 

All Greek to me Bob, and thanks to the others for pitching in with their thoughts and tech help.  If it makes any difference the default fall back antenna may be best being made Antenna 1 - for the multiband HF beam most of us use. If the radio coupled to an external device, such as a linear amp which stays turned off a lot of the time, generally the relay on the linear drops back to allow Antenna 1 connection on the linear to remain connected straight through with the power to the linear switched off.  Antenna 3 is selectable on the 101 series as a receive antenna only via the menu, although few of us have that luxury, so not as important to my mind as having 3 antenna connections which one can transmit into on different bands. 

73 Phil  

Re: CAT Control of FTDX101 via Logger 32

Darren Collins (G0TSM)
 

When the FTDX5000 came out Bob corrected the same issue ( I think)
Logger32 needs to send the band command first and then the mode and frequency.

Sending the BS command will put the rig on the right band and the band stack registers select the antenna, ipo, att, etc. This should be immediately followed by the mode and freq. I think that’s right.

Sorry I’m away from the shack this week so can’t check at home, but I did have a glance through the pdf for the 101’s CAT commands, and it appears to be similar.

73 Darren G0TSM





On 4 Nov 2019, at 13:05, Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Philip (G4OBK) Catterall
 

Happy to oblige Bob - thank you very much - I am away tomorrow but back by the evening time your a star, thank you. 

BREXIT DITCHED AND STOPPED (for 3 more months - possibly forever). 

73 Phil

Re: CAT Control of FTDX101 via Logger 32

Dave Colliau
 

That would be interesting. I dont actually have a 101 I have a 5k but I will look at the cat commands for both rigs and see what I can see just for fun. I think the only way the 5k knows what antenna to use is from memory settings.
Dave N8DC

On November 4, 2019 at 8:11 AM Bob <k4cy@...> wrote:

Dave, could it be that you can set the radio to operate cross band, when doing this the antenna selected when transmitting may be different to the one for receiving. Do I really want to get in the middle of this? SeventyThree(s).
On November 4, 2019 at 8:05 AM Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Dave Colliau
 

Your asking me ? you wrote the program Ha Ha..  Seriously I have no idea Bob. How would Logger 32 know what antenna is hooked to what output on the rig or how to decipher it from the setup ?
Have fun
Dave N8DC 

On November 4, 2019 at 8:05 AM Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Dave, could it be that you can set the radio to operate cross band, when doing this the antenna selected when transmitting may be different to the one for receiving. Do I really want to get in the middle of this? SeventyThree(s).

On November 4, 2019 at 8:05 AM Bob <k4cy@...> wrote:

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).
On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Dave, I see that, but how does Logger32 know when to use P1=0 or P1=1? SeventyThree(s).

On November 4, 2019 at 7:57 AM Dave Colliau <n8dc-8@...> wrote:

p1=0 p2=1 that would be main band antenna 1
Dave N8DC
On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Dave Colliau
 

p1=0 p2=1 that would be main band antenna 1
Dave N8DC

On November 4, 2019 at 7:54 AM Bob <k4cy@...> wrote:

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)
On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

 

Re: CAT Control of FTDX101 via Logger 32

Bob
 

I see this in the Yaesu destructions:



What is main/sub band? What do I use for the P1 value? SeventyThree(s)

On November 4, 2019 at 7:21 AM Bob <k4cy@...> wrote:

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).
On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

 

Re: CAT Control of FTDX101 via Logger 32

Bob
 

Phil, looking at the code, I see antenna switching CAT is coded for Icom and the  FT-2000, FT-9000 and FT-5000. But not the FT-991 (I have no idea if it has that capability. If it does, no one has whined yet). In Logger32 the FT-101D and FT-101MP is actually the FT-991 code (it's all smoke and mirrors). So it follows that there 'ain't any antenna commands being sent to either the 101D or 101MP. So, what are the appropriate CAT commands? I'll add them (and probably add the FT-101MP radio type while I'm in there mucking around). Then I'll send you a test version just in time for Guy Fawkes ... SeventyThree(s).

On November 4, 2019 at 3:51 AM "Philip (G4OBK) Catterall" <cq@...> wrote:

HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

 

Re: CAT Control of FTDX101 via Logger 32

Vince Shirley
 

Phil,

I noticed this from day 1 with my 101D.

I believe it to be a problem with the radio CAT set as Logger32 does not send antenna information with its request as it can not know which antenna is for which band.

I guess its up to Yaesu to sort it out.

Vince G0ORC



On Mon, 4 Nov 2019 at 08:51, Philip (G4OBK) Catterall <cq@...> wrote:
HI Bob / All

I've just moved over from using the Yaesu FTDX5000 to the FTDX101MP. I configured the CAT for the FTDX101MP within Logger 32 via RS232 using the same microHam Keyer virtual COM port for the CAT connections as I used on the FTDX5000. In Setup Radio 1 I chose Radio FT-101D Com 7, 9600 baud, Datbits 8, Stop bits 1, Parity None. DTR & RTS High, polling interval 100 ms, use narrow CW filter.  The FT-991 radio if selected will also work. The CAT works - however: 

Whilst the CAT works as it should in terms of clicking on a DX spot from the Logger DX Spots window which puts the FT-101 on to the correct frequency and mode, the antenna does not switch to the correct one for the specific band as it did on the FTDX5000. The antenna remains fixed and does not switch.  i.e. There are 3 antenna inputs on the FT-101 for different bands.  If I manually change bands on the FT-101 with the band switches on the radio the antenna changes to the appropriate one for that band as it should, but it doesn't switch as it should using CAT via Logger 32, yet it did with the FTDX5000 setup! 

Could it be that there are differences between the software in Logger 32 that controls the CAT settings relating to antenna switching between the FTDX5000 and the FT-101D? Maybe some code is missing? 

73 and thanks de Phil G4OBK 

Re: ADIF Editing

Bob
 

Dave, that's why you have the option to simply accept the recommended changes automatically or be prompted to manually OK each one. FWIW, I would resubmit (one by one) the anomalies to Club Log. While they do have a 560M QSO database, they can only be as accurate as we help them be. Every anomaly we point out, and they correct, makes it that much better for everyone that follows. A scan of the card that shows the call/country/date compared to the Club Log prognostication should do the trick. Again, FWIW, it has been my experience that they are both mercuric and precise in their support. SeventyThree(s).

On November 4, 2019 at 5:49 AM Dave Hobro <david@...> wrote:

Hi Ken, Gary
I have emailed Michael, G7VJR twice, and raised a ticket about this issue but not a single reply to date (approx 2 years ago).  I have got an on-line DXCC application on the ARRL website, this is correctly identifying all of the ClubLog "errors" as deleted countries.  My LoTW, on-line DXCC and Logger32 DXCC totals agree with each other regarding deleted countries - it is the ARRL that run the DXCC countries list so at least LoTW and an on-line DXCC should be correct. As the QSL card was originated by the DX station, I am quite happy to go with the information on the card rather than risk the integrity of my logbook by importing a third party file which may imbalance the totals.  I may be the exception to the rule over this but for me ClubLog is a non-starter.

73's
Dave, G4IDF