Date   

moderated Re: Audio Forwarding to Annuncicom

Stefan Giessler
 

Hi,

I guess your Avtex Console is sending a RTP stream (?). 
The Annuncicom Standard firmware supports only RAW UDP, but not RTP.
I recommend to change to the firmware on your Annuncicom, e.g. to IP-Intercom firmware, this supports G.711 8kHz even in RTP.
You can download the IP-Intercom firmware for free from the Barix homepage.
Guess that can solve the issue.

Best greetings
stefan


moderated Audio Forwarding to Annuncicom

ebihlajama@...
 

We have an IP based Avtec console system that sends audio to recorders/etc using industry standard audio forwarding via uLaw 8bit G711 streaming.  It's configured to send the stream via UDP to the Annuncicom's IP addrress on port 60030.  DSCP is set for voice at B8 and all metadata is shut off.

In the Annuncicom, I have it configured for receive only listening on UDP RX port 60030.  All other IP and port settings are at 0.0.0.0 and 0, and all TX and IO settings are disabled.

I'm hearing the audio stream on the Annuncicom  but it has a very strong 'buzz' to it.  If I send the stream to the IP and port of my recorder there's no 'buzzing' sound at all, just clear audio.

Any suggestions on what might be happening here?  It's sounds almost like there's a gap between packets, like what you'd hear on Voip when your ptimes don't match.  I've already tried the default port 3030, same result.

Thanks in advance!


moderated Re: SNMP OID values

Stefan Giessler
 

Hi Christal,
 
this is a BOSCH product, probably it is better to contact the Bosch Product Support.
 
Best greetings
Stefan


moderated Re: SNMP OID values

Jothi Christal (BT/SEM-SPO)
 

Dear Stefan,

 

Thank you very much for your quick response.

 

It is needed for Bosch PRS-1AIP1 Firmware V2.06

 

Best regards / أطيب التحيات

Christal Jothi


Sales Project Office - Middle East (BT/SEM-SPO)
Robert Bosch Middle East FZE | Dubai Airport Free Zone | West Wing 5A Office 701 | P.O. Box 54307 | Dubai, U.A.E. | U.A.E
Tel. +971 4 2123 -353 | Mobile +971 50 7083056 | Fax +971 4 2123 -388 | Christal.Jothi@...

From: annuncicom@groups.io <annuncicom@groups.io> On Behalf Of Stefan Giessler via groups.io
Sent: Tuesday, November 24, 2020 5:49 PM
To: annuncicom@groups.io
Subject: Re: [annuncicom forum] SNMP OID values

 

Hello Christal,

for which firmware you are asking ?
And you are asking for Annuncicom1000 or PRS-1AIP1 ?

Best regards
Stefan


moderated Re: SNMP OID values

Stefan Giessler
 

Hello Christal,

for which firmware you are asking ?
And you are asking for Annuncicom1000 or PRS-1AIP1 ?

Best regards
Stefan


moderated SNMP OID values

Jothi Christal (BT/SEM-SPO)
 

Dear 
Can you please help me to find SNMP OID values for power failure of Annucicom 1000


moderated new Any to All firmware v2.03 published

Stefan Giessler
 

Hello,

we are happy to inform about a new Any 2 All firmware version 2.03 we have published on the Barix homepage.
The new version has few minor improvements, all details you can find in the according release notes.

https://www.barix.com/fileadmin/data/releasenotes/Any_to_All_PA_App/release_notes_v0203.pdf

Best regards
Barix Support 


moderated Re: Annucicom with SIP

Barix Support Ticket
 

Hi Stefan,

yes, we offer a SIP Client firmware which allows to intregrate the Barix Audio devices into a SIP PBX
or to work in P2P mode via SIP. It supports incoming and outgoing calls, relay and many other feature.

The SIP Client fimrware you can download from here :

To download it you have to register and to login on the Barix homepage. 

Best regards
Barix Support

---- an Thu, 5 Dec 2019 13:50:15 +0100 "Stefan Giessler"<stefan@... hat geschrieben ----
Hi,

can I integrate the Annuncicom100 on our SIP server and use it with SIP ?

Greetings
Stefan






moderated Annucicom with SIP

Stefan Giessler
 

Hi,

can I integrate the Annuncicom100 on our SIP server and use it with SIP ?

Greetings
Stefan

1 - 9 of 9