Re: UV light box


Darkrooms, Department of Art <darkroommanager@...>
 

The "fast" unit is very warm indeed. A 30min cyanotype exposure produces
a pretty warm print.

Best,
Jennifer M. Gioffre
Teaching Support Specialist

Architecture Art and Planning
Cornell University
120 Tjaden Hall
Ithaca, NY 14853

o: 607-255-4207
f: 607-255-3462
Jmg393@cornell.edu
Darkroommanager@cornell.edu
AAPstore@cornell.edu

On 3/6/14 10:41 AM, "andy schmitt" <aschmitt@aandy.org> wrote:

WOW...The heat generated by the "slow" unit must be much less than the
other one. Not a bad tradeoff for a 10% increase in exposure time.
I probably need to build another box for Peters Valley school of Craft's
Photo Department and that would save me some $$$...always a nice thing
for an NPO..
Thanks

Regards

Andy Schmitt PPA

Head of The New & Improved Photography Dept,
Peters Valley School of Craft
http://www.petersvalley.org/html/Photography.cfm



-----Original Message-----
From: Alt-photo-process-list
[mailto:alt-photo-process-list-bounces@lists.altphotolist.org] On Behalf
Of Darkrooms, Department of Art
Sent: Thursday, March 06, 2014 9:28 AM
To: alt-photo-process-list@lists.altphotolist.org
Subject: Re: [Alt-photo] UV light box

Here at the university we have two exposure units. Both use the same bulb
T12 40BL GE bulbs, 48" length. In our "fast unit" the bulbs are 1 inch
apart and about 3" from the surface of the print. The "slow" unit has
bulbs that are 6" apart and about 8" from the surface of the print. I
find that both have even illumination throughout, but the slow unit has
exposure length about 10% longer.

I hope that this is helpful! Good luck and happy printing.

Best,
Jennifer M. Gioffre
Teaching Support Specialist

Architecture Art and Planning
Cornell University
120 Tjaden Hall
Ithaca, NY 14853

o: 607-255-4207
f: 607-255-3462
Jmg393@cornell.edu
Darkroommanager@cornell.edu
AAPstore@cornell.edu




On 3/6/14 7:45 AM, "Jorj Bauer" <jorj@jorj.org> wrote:

I think you'll be fine.

I built a 24" square exposure box from 10x GE 22" blacklight enclosures
(it was what was readily available, so I ran with it). The prints sit
about 6" above the bulbs (I flip over my vacuum frame, so it's
upside-down during exposures).

The bulbs are spaced evenly across the box, which means they're a
little over 2" apart. But I wired it so that there are two power
switches, one for bulbs 1,3,5,7,9 and one for 2,4,6,8,10 (so that I can
turn off half the bank if I want to - I didn't know if this would be
overkill in terms of UV source or not).

I ran some tests using half of the bulbs - so, spaced a little over 4"
apart - and saw no problems. I've always used all of the lights since,
though. My average exposure time is around 6 minutes for most kinds of
prints.

The lights are GE model 10186, 15w blacklight T8s.

Hope that helps,
-- Jorj


On Mar 5, 2014, at 10:42 PM, Bob Cornelis <bob@colorfolio.com> wrote:

Thanks, Marek!

I¹m getting the impression my hope of putting the bulbs 4² apart is
very misguided and that they need to actually be quite close to each
other.

Regards
Bob


--------------------------------------
Color Folio
www.colorfolio.com

Become a fan of Color Folio on Facebook

http://www.facebook.com/ColorFolio

2550 Lewis Dr.
Sebastopol, CA 95472
707.824.8910
888.212.7060 toll free






On Mar 5, 2014, at 7:29 PM, Marek Matusz <marekmatusz@hotmail.com>
wrote:

Ok mine home build unit has the tubes 3" from the print this is the
distance from the edge of the tube. Distance between the tubes again
edge to edge of tubes is 0.5"

Sent from my iPhone

On Mar 5, 2014, at 6:41 PM, "Laura V" <laura@lavatop.com> wrote:

Hi Bob,
I was asking here about lighting a couple of months ago and got
this link from Kees Brandenburg showing his lightbox (maybe he's too
busy moving the list to see this thread) :)
http://polychrome.nl/techlog/simple-and-cheap-uv-unit

As you can see, the bulbs look pretty close together. I ended up
having a similar unit built (which took almost 3 months - I just
picked it up so haven't tried it yet!) I had the electrical part
done at a place specializing in fluorescent lighting and asked them
to put the bulbs as close together as was safe to do so. It's in the
trunk of my car down the street at the moment and it's snowing, so
I'll get back to you as to the exact distance. Mine has 10 bulbs and
the width is smaller than the 24" (60cm) length, so that is a lot
closer than 4 inches apart.

Perhaps someone else can fill us in whether they need to be that
close together, or maybe it's just a matter of the more bulbs the
quicker the exposure.

Best Regards,
Laura

On 3/4/14 9:43 PM, Bob Cornelis wrote:
I am planning on building a UV light box and have a question about
the layout of the bulbs. Upon the recommendation of a friend who
does alt process work I plan on buying these tubes:

http://www.1000bulbs.com/product/2220/F-20T12BL.html

My questions are how far apart should I mount these and how many
do I need to provide good coverage to expose up to 20x24² (though
I¹m not sure I¹d ever go over 16x20). I plan on having them about
4² above the surface of the prints.

Thanks
Bob

----------------------
707.824.8910
http://www.bobcornelis.com
http://bobcornelis.wordpress.com




_______________________________________________
Alt-photo-process-list | altphotolist.org
_______________________________________________
Alt-photo-process-list | altphotolist.org
_______________________________________________
Alt-photo-process-list | altphotolist.org
_______________________________________________
Alt-photo-process-list | altphotolist.org
_______________________________________________
Alt-photo-process-list | altphotolist.org
_______________________________________________
Alt-photo-process-list | altphotolist.org

_______________________________________________
Alt-photo-process-list | altphotolist.org

Join altphotolist@groups.io to automatically receive all group messages.