|
locked
sticky
How to use the Co-Channel Canceller in SDR# 2 messages
*Some basic background* The plugin locks to the dominant carrier and cancels all the correlated frequency bands around it. If the signal is distorted (which results in bad correlations), it tries to f
*Some basic background* The plugin locks to the dominant carrier and cancels all the correlated frequency bands around it. If the signal is distorted (which results in bad correlations), it tries to fix it using some fancy statistics. *How to use the plugin*
By prog
·
|
|
moderated
sticky
SDR# Updates 24 messages
#announcements
So, instead of having a new topic for every SDR# update, let's try to have a read-only stream with just the bare minimum of information and avoid too much noise. Rev 1760 : Added Peak Hold in the spec
So, instead of having a new topic for every SDR# update, let's try to have a read-only stream with just the bare minimum of information and avoid too much noise. Rev 1760 : Added Peak Hold in the spectrum display. This can be enabled/disabled/reset using a right click on the spectrum. The color of the Peak Hold can be set using spectrumAnalyzer.peakColor. Download link: https://airspy.com/download
By prog
·
|
|
Russian translation of the SDR# User Guide by Дмитрий Мезин (Dmitry Mezin, UA4004SWL)
For our Russian friends: https://airspy.com/download/
For our Russian friends: https://airspy.com/download/
|
By prog
·
|
|
Help needed Airspy HF+ Discovery Plug and Play drivers 8 messages
Greetings I have received eagerly awaited Airspy HF+ discovery today. I am using a Dell Latitude laptop with bags of oomph and have previously used it with an RTl dongle and the Airspy progreamme; als
Greetings I have received eagerly awaited Airspy HF+ discovery today. I am using a Dell Latitude laptop with bags of oomph and have previously used it with an RTl dongle and the Airspy progreamme; als
|
By paul newland
·
|
|
Airspy HF+ preselector 134 messages
#airspyhfplus
Hello guys, i'm looking to add the preselector inside my Airspy HF+. I know that a preselector it has been put inside the new Airspy Discovery. Where i can buy this unit? Anyone could help me? Tnx, Me
Hello guys, i'm looking to add the preselector inside my Airspy HF+. I know that a preselector it has been put inside the new Airspy Discovery. Where i can buy this unit? Anyone could help me? Tnx, Me
|
By valerio spagnolo
·
|
|
1540 USA KXEL Received in Botswana 14110km Airspy HF+ Discovery 2 messages
My best distance yet for MWDX. The antenna is just an outdoor telescopic whip. https://youtu.be/PCqlKuvoNyU Peter Botswana
My best distance yet for MWDX. The antenna is just an outdoor telescopic whip. https://youtu.be/PCqlKuvoNyU Peter Botswana
|
By Peter 1956
·
|
|
Airspy R2 running on a Web Browser 7 messages
So, web browsers are now fast enough to run libairspy and some DSP and perform just fine. Demo courtesy of Luigi Cruz https://twitter.com/luigifcruz/status/1352147996096552960
So, web browsers are now fast enough to run libairspy and some DSP and perform just fine. Demo courtesy of Luigi Cruz https://twitter.com/luigifcruz/status/1352147996096552960
|
By prog
·
|
|
Plugin Development... 7 messages
I just wanted to let everyone know that going forward into the future I will cease to release new plugins for SDR#. As of tonight I will be removing all download links to my SDR# plugins. I originally
I just wanted to let everyone know that going forward into the future I will cease to release new plugins for SDR#. As of tonight I will be removing all download links to my SDR# plugins. I originally
|
By Edward MacDonald
·
|
|
High speed USB and Virtual Machines 13 messages
I have a Discovery and an HF+. I would like to run one of them in a Windows 10 Virtual Machine. However neither SDR#, HDSDR, or Device Manager can find the receiver. Is there a way to make this work?
I have a Discovery and an HF+. I would like to run one of them in a Windows 10 Virtual Machine. However neither SDR#, HDSDR, or Device Manager can find the receiver. Is there a way to make this work?
|
By Pete Ferrand
·
|
|
Spyserver windows version 12 messages
Good day to all, I had set up a older laptop with W10 and the latest version of Spyserver. Easy to set up and works quite well locally. I pulled up the spyserver network map and to my surprise the gre
Good day to all, I had set up a older laptop with W10 and the latest version of Spyserver. Easy to set up and works quite well locally. I pulled up the spyserver network map and to my surprise the gre
|
By Glenn Blum
·
|
|
Help me debug my CAT Control 4 messages
Hi all, I am using 2 com0com Port pairs. COM3/4 and COM5/6 to CAT control two SDR# slices from two instances of Faros 1.4. I ran into an issue with SDR# multi slice and CAT Control. When I start one a
Hi all, I am using 2 com0com Port pairs. COM3/4 and COM5/6 to CAT control two SDR# slices from two instances of Faros 1.4. I ran into an issue with SDR# multi slice and CAT Control. When I start one a
|
By
Roland
·
|
|
630m DX by Airspy 9 messages
Last night, I've received VK5FQ-Australia on 630m band using Airspy HF+Discovery and 14MHz Delta Loop Antenna. The distance is about 7,966km from my home. Mode is FST4W-300Sec(Mode5) decordig software
Last night, I've received VK5FQ-Australia on 630m band using Airspy HF+Discovery and 14MHz Delta Loop Antenna. The distance is about 7,966km from my home. Mode is FST4W-300Sec(Mode5) decordig software
|
By Hidehiko Komachi - JA9MAT
·
|
|
Using external 1PPS to trigger data capture on Airspy R2 2 messages
#airspyr2
Hi folks, I've been looking at if it is possible to use an external signal (e.g. 1PPS) to trigger data capture on an airspy R2. This question has been asked before, but there isn't a definitive answer
Hi folks, I've been looking at if it is possible to use an external signal (e.g. 1PPS) to trigger data capture on an airspy R2. This question has been asked before, but there isn't a definitive answer
|
By Randall Wayth
·
|
|
Simple way to couple signals out of your homebrew loop to you SDR
In this video, as in several of the last videos we talk about loop antennas. But this time we take a look at a super simple way to couple any loop to your SDR. In this case we are using the HF Discove
In this video, as in several of the last videos we talk about loop antennas. But this time we take a look at a super simple way to couple any loop to your SDR. In this case we are using the HF Discove
|
By Paul Cianciolo
·
|
|
Headless SDR Audio-only SDR 2 messages
I'm an AirSpy HF+ owner, and a sw engineer. My google searches have lead me nowhere. I'm looking for a headless SDR to stream audio, over VoIP, probably. I'm a long-time C# guy, so that is the preferr
I'm an AirSpy HF+ owner, and a sw engineer. My google searches have lead me nowhere. I'm looking for a headless SDR to stream audio, over VoIP, probably. I'm a long-time C# guy, so that is the preferr
|
By Gerry Hull
·
|
|
Decoding digital modes, 14 messages
#airspydiscovery
Happy New Year folks! I am wondering if anyone has successfully used MultiPSK or similar software to decode the digital modes on HF? If so, what did you use, was it hard to configure and does it work
Happy New Year folks! I am wondering if anyone has successfully used MultiPSK or similar software to decode the digital modes on HF? If so, what did you use, was it hard to configure and does it work
|
By Jim Widgren
·
|
|
Visual FFT gain when using Spyserver 5 messages
Hi! I'm using an Airspy R2 with latest version of Spyserver (2.0.1700) on a Raspberry Pi4 (on local WLAN) and SDR# (1784) on a laptop and noticed a 30dB increase of the noise floor when turning off th
Hi! I'm using an Airspy R2 with latest version of Spyserver (2.0.1700) on a Raspberry Pi4 (on local WLAN) and SDR# (1784) on a laptop and noticed a 30dB increase of the noise floor when turning off th
|
By G Davidson
·
|
|
Any benevolent developer to help me with 4 messages
#airspyr2
#firmware
#request
Hello! Can someone please help me creating a firmware for Airspy R2 that has CLK4-6 enabled with 10 MHz output? GPS 10 MHz reference in Regards Simon
Hello! Can someone please help me creating a firmware for Airspy R2 that has CLK4-6 enabled with 10 MHz output? GPS 10 MHz reference in Regards Simon
|
By simontoyra@...
·
|
|
How to disable the screen reader in the Community Package 5 messages
Received this week Discovery+ and installed the community package fron Rodrigo. One thing which irritates me is the voice over if you swith menus. Could not find how to turn it off. Maybe I overread i
Received this week Discovery+ and installed the community package fron Rodrigo. One thing which irritates me is the voice over if you swith menus. Could not find how to turn it off. Maybe I overread i
|
By Ronald
·
|
|
Discovery High speed USB and Virtual Machines 7 messages
Somehow my original email got changed from Sandbox to Virtual Machines. In Windows 10 a virtual machine is one thing, a sandbox is another. I'm talking about the sandbox provided with Windows 10 pro.
Somehow my original email got changed from Sandbox to Virtual Machines. In Windows 10 a virtual machine is one thing, a sandbox is another. I'm talking about the sandbox provided with Windows 10 pro.
|
By Pete Ferrand
·
|