Date   

Re: Can you try my server?

Roberto Zinelli
 

#40 meter band is open this evening is you are able to connect to my server.
#
#k2sdr.dyndns.org
#
#Jeff

Hey Jeff, your SpyServer work very fine. For test i tuned on 7074 USB, routed the output on WSJT with virtualcable and decoded some signal... Fantastic!

Where is locate your server?


73 de IW4ENS
Roberto

 

On Sun, Oct 8, 2017 at 11:49 PM, Jeff Kelly <jkelly@...> wrote:
40 meter band is open this evening is you are able to connect to my server.

k2sdr.dyndns.org

Jeff



On 10/7/2017 3:28 AM, pd0rtl via Groups.Io wrote:
not even AM, SSB also max 4.9khz, looks a hickup in the config max BW seting
i tried stock 1590, and my upgraded version.
bcouse i also listen,cough,to DRM a BW of 10khz is needed un SSB

wile in SDR# 1577 i can tune in SSB max 19khz and in AM 39 KHZ BW!


On 5-10-2017 16:28, Meduzi Jellyfish wrote:
AM seems to be limited to 9.765 KHz.

WCBS on 880 KHz in New York seems to be using 20K bandwidth so it's a
shame that it's too narrow to sound its best.










Re: De-emphasis in NFM WFM

Julian
 



Filter wise:
JPEG Left is NFM - Filter Audio not applied, no HPF LPF at edges.
JPEG Right is WFM - Filter Audio makes no difference.

I am not sure whether de-emphasis is represented by WFM audio spectrum which drops at 15k? Or is it simply a default WFM HPF (which cannot be changed)? De-emphasis only applies to modulated (stronger) signal or the noise floor is also affected by it?

I would like to know whether de-emphasis is applied (as in a hardware receiver) in order to see whether the 2200Hz and 1200Hz demodulated signals are at the same amplitude.


Re: New Firmware for Airspy R2?

prog
 

So the streaming and the IQ conversion are all fine. You should check if your system has enough processing power left for the WX app.


Re: New Firmware for Airspy R2?

Ruben Navarro Huedo (EA5BZ)
 

Yes..average is 10.005


Re: De-emphasis in NFM WFM

prog
 

There's a difference between the deemphasis and the bandwidth limits set by the HPF's and LPFs. If you need the raw demodulated signal without any filtering, uncheck the "Filter Audio" box.


Re: New Firmware for Airspy R2?

prog
 

Did you run the diagnostic tools as described in the quick start?


De-emphasis in NFM WFM

Julian
 

Hi, I would like to know whether SDR Sharp applies de-emphasis to the FM signals received. I have seen few other posts re this matter on the group, but there were some ambiguities there. I could see that in WFM mode, the audio spectrum in SDR# drops and gets cut at 15k, but in NFM is untouched. I am trying to study the amplitude of 1200 and 2200 Hz demodulated FM signals, used in packet radio, at various deviation values ( https://www.febo.com/packet/layer-one/transmit.html ).


Re: airspy HF + availability to public #airspyhfplus

prog
 

On Mon, Oct 9, 2017 at 10:19 am, Leif Asbrink wrote:
The drawback should be that with twice the analog
bandwidth, the peak signal level would be 6 dB
higher but the analog noise floor would be the same
so a 6 dB better IP3 would be required for for
the same performance in terms of freedom from
false signals caused by intermodulation.
That's exactly why the design is the way it is now.


Re: New Firmware for Airspy R2?

PMM
 

Could be running into usb issues / usb noise causing dropped samples not all usb made equal I run mine off a port 4 hub as can supply cleaner power but have run into issues like that in past with my bladerf on usb3 one port better than the other different chipset. 

Some usb can be quite noisy can also be quite a difference between back of PC motherboard ports verse panel mount.

I highly suggest trying out different ports to see if any work better.

On 9 Oct 2017 18:48, "Ruben Navarro Huedo (EA5BZ)" <runahue@...> wrote:
All is ok at 2.5 MSPS and not at 10MSPS (using decimation)


Re: New Firmware for Airspy R2?

Ruben Navarro Huedo (EA5BZ)
 

All is ok at 2.5 MSPS and not at 10MSPS (using decimation)


Re: New Firmware for Airspy R2?

PMM
 

Not had issues with weather Sat's, certainly use decimation but also ensure things like agc are off and anything that would have knock on effect to signal e.g. noise blanking as you will end up passing that on to wxtoimg also probably the audio filter off so it not potentially effect your tick tock lol 

On 9 Oct 2017 18:27, "Ruben Navarro Huedo (EA5BZ)" <runahue@...> wrote:
I don't understand the cause, but I have problems with 10MSPS and WXTOIMG.... i must use 2.5.
Using 10MSPS i have synchronization problems, not using 2.5.


Re: New Firmware for Airspy R2?

Ruben Navarro Huedo (EA5BZ)
 

Ignacio: How do i activate data packing under SDRSHARP?


Re: New Firmware for Airspy R2?

Ruben Navarro Huedo (EA5BZ)
 

Hello Ignacio.

Yes...i was using 10MSPS with 32 decimation, and i don't have audio problems but i have sync problems with WXTOIMG (I don't know the cause).

Ignacio: He estado usando mucho tiempo 10MSPS con 32 de decimation, pero por un motivo que desconozco tengo problemas de sincronia entre SDRSHARP y WXTOIMG.
WXTOIMG no consigue mantener las imagenes "rectas" y esto no ocurre a 2.5 MSPS.


Re: New Firmware for Airspy R2?

EB4APL
 

Hi Ruben,

I always use 10 MSPS with the same programs without any problem and my PC is a mere I5. I think that your USB is losing some data at 10 MSPS hence the sync problem. Are you using data packaging? It does not work very well in my computer.

73 de Ignacio, EB4APL


El 09/10/2017 a las 19:27, Ruben Navarro Huedo (EA5BZ) escribió:
I don't understand the cause, but I have problems with 10MSPS and WXTOIMG.... i must use 2.5.
Using 10MSPS i have synchronization problems, not using 2.5.

_


Re: New Firmware for Airspy R2?

EB4APL
 

Hi,

The author will know better, but I think that you can use decimation to lower the effective sample rate instead of this experimental mode.

73 de Ignacio, EB4APL


El 09/10/2017 a las 18:55, Ruben Navarro Huedo (EA5BZ) escribió:
Hello:
I have the problem with 2.5MSPS described under Quick Start Guide.: http://airspy.com/quickstart/
>> In some PCs, the experimental 2.5MSPS mode is vulnerable to USB noise. This will be improved with further firmware updates.

Will we have a new firmware solving it?

Thank's a lot.


Re: New Firmware for Airspy R2?

Ruben Navarro Huedo (EA5BZ)
 

I don't understand the cause, but I have problems with 10MSPS and WXTOIMG.... i must use 2.5.
Using 10MSPS i have synchronization problems, not using 2.5.


Re: airspy HF + availability to public #airspyhfplus

Leif Asbrink
 

Hi Yussef,

prog" <info@sdrsharp.com> wrote:

The 6 dB gain reduction might bring the analog noise below the
ADC noise in which case dynamic range would suffer.
This can never happen by design. Many AGC loops are involved
to ensure optimal SNR and available dynamic range. The real
concern is the DR of the analog chain.

The output is 768 KSPS IQ with 660 kHz alias-free.
The DDC and the analog filters can be configured to
output more bandwidth at the cost of much less usable
dynamic range.
I do not understand this statement. As a general statement
it is incorrect and it would be interesting to know
something about why the Airspy HF+ has thais peculiar
behaviour.

If you would double the sampling rate to 1536 kHz for
an alias-free range of perhaps 1260 kHz, dynamic range
as measured with a strong and a weak signal separated
by 25 kHz or 100 kHz should not change. Both signals
would be within the analog passband in both cases
which implicates that all AGC loops will have the
same state in both cases with only the single strong
signal affecting the AGC.

The same with an IM3 test where both signals as well
as the IM3 products are within the analog passband.

The drawback should be that with twice the analog
bandwidth, the peak signal level would be 6 dB
higher but the analog noise floor would be the same
so a 6 dB better IP3 would be required for for
the same performance in terms of freedom from
false signals caused by intermodulation.


73

Leif


Re: SpyServer RTL's Direct Sampling? #RTL #spyserver

matteo cantarella
 

Well, knowing that it is possible is at least a start! =) 

Congrats, SDR# package is an excellent piece of software, absolutely love it and the constant support/update effort you're putting in it!


Re: SpyServer RTL's Direct Sampling? #RTL #spyserver

prog
 

Possible, but not planned. No time to code/test it.


Re: New Firmware for Airspy R2?

prog
 

Nothing planned yet. Use the recommended sample rate with the decimation.

17281 - 17300 of 41307